• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.220-230
• /
• 1993

Photoelastic isochromatic fringes related to the difference of principal stresses have some bandwidth whose light intensities are not constant and asymmetrical in experimental images. Hence, it is difficult to measure fringe order accurately at a data point by visual observation. In this study, a method of fringe sharpening, which can extract shapened lines from both full-and half-order fringes by digital image processing, is developed. To test the method, various simple photelastic fringe patterns are simulated and their images are processed to yield sharpened lines. The method is then applied to general problems such as images of a circular disk compressed by diametrically concentrated loads and a circular cylinder sybject to internal pressure. The procedure is proved to be capable of extracting sharpened lines accurately from photoelastic isochromatic fringes.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.1
• /
• pp.1-8
• /
• 2005

This paper presents the experimental results measured by photoelastic 4-step phase shifting method for the isochromatic fringe distribution in a TV glass panel. In the conventional photoelastic method, the isochromatic fringe orders are measured manually point by point. The 4-step phase shifting method uses four images obtained from a circular polariscope by rotating the analyzer to $0^{\circ},\;45^{\circ},\;90^{\circ}$, and $135^{\circ}$. In order to use the 4-step phase shifting method, the elements of a polariscope should be aligned to isoclinic direction at a point and/or along a line where isochromatic fringe distribution is measured. Experimental results obtained from the 4-step phase shifting method are compared with those measured by the Senarmont compensation method. Both results are well agreed. Then, isochromatic fringe distributions in the TV glass panel that is heat-treated before and after are compared. Maximum and minimum isochromatic fringe orders in the TV glass panel with before- and after-heat treatment are changed approximately two times.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.3 s.192
• /
• pp.31-39
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.127-133
• /
• 2001

Photoelastic isochromatic fringes related to the difference of principal stresses have some bandwidth whose light intensities are not constant and unsymmetrical in experimental image. Hence it is difficult to measure fringe order accurately at a data point by visual observation. In this study, the method of fringe sharpening, which can extract sharpened lines from both full-and half-order fringes by digital image processing, is developed. To test the method, various simple photoelastic fringe patterns are simulated and their image are processed to yield sharpened lines. The method is than applied to general problem such as image of a circular disk compressed by concentrated loads and a cylinder subjected to internal pressure. The procedure is proved to be capable of extracting sharpened lines accurately from photoelastic isochromatic fringes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.11
• /
• pp.1776-1785
• /
• 2004

In this research, the relationships between static bimaterial constant and dynamic oscillation index are studied. It was certified that static bimaterial constant has the same form equation as the dynamic oscillation index. Bimaterial constant and oscillation index are increased with the increment of Young's modulus ratio and approached to the some value. Isochromatic fringe patterns are slanted to the left side with increment of bimaterial constants and oscillation index. Though patterns of stress components in above the crack surface are similar to each other, their magnitudes are different a little. In the ahead of crack tip, there are big differences in the isochromatic fringe patterns and their magnitudes. The influence of bimaterial with Young's modulus ratio is bigger in the propagation crack than in the stationary crack.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.3
• /
• pp.200-206
• /
• 1999

This paper describes the stress analysis of a curved beam by using photoelasticity. In order to measure accurate isochromatic fringe orders at certain locations. fringes are doubled and sharpened by digital image processing. After fringe multiplication and sharpening. fringe orders can be read as a quarter order interval (N=0, 1/4, 2/4, 3/4,...). The results obtained from photoelastic experiment are compared with those calculated by using theory. Two results are agreed well even though there are some scatter bands with maximum 8 percent for the results of photoelastic measurements and theoretical calculation. Difference may be occurred due to the slight misalignment of the direction to which axial load is applied in photoelastic experiment. It is confirmed that accurate measurement of stress distribution can be possible by using the techniques of fringe multiplication and sharpening in photoelasticity.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.172-179
• /
• 2001

The effects of the interface and two holes located near the crack path in the hybrid specimen on the dynamic crack propagation behavior have been investigated using dynamic photoelasticity with the aid of Cranz-Shardin type high speed camera system. The dynamic stress field around the dynamically propagating interface crack tip in the three point bending specimens under a dynamic load applied by a hammer dropped from 0.6m high without initial velocity are recorded. The complex stress intensity factors for the dynamically propagating interface crack are extracted by using a overdeterministic least square method. Theoretical dynamic interface isochromatic fringe loops generated by using the numerically determined complex stress intensity factors are compared with the experimental results. Furthermore, the influence of the hole to the dynamic interface crack velocities has been investigated experimentally.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.146-151
• /
• 2001

The effects of slant interface in the hybrid specimen on the dynamic crack propagation behavior have been investigated using dynamic photoelasticity. The dynamic photoelasticity with the aid of Cranz-Shardin type high speed camera system is utilized to record the dynamic stress field around the dynamically propagating inclined interface crack tip in the three point bending specimens. The dynamic load is applied by a hammer dropped from 0.08m high without initial velocity. The dynamic crack propagation velocities and dynamic stresses field around the interface crack tips are investigated. Theoretical dynamic isochromatic fringe loops are compared with the experimental reults. It is interesting to note that the crack propagating velocity becomes comparable to the Rayleigh wave speed of the soft material of a specimen when slant angle decreases.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2577-2584
• /
• 1994

A method of digital image processing thechnique, which can multiply and sharpen isochromatic fringes in photoelasticity on both occasions, is developed. To test the method, photoelastic fringe patterns of a disk compressed by two diametrically opposite cocentrated loads are simulated and these patterns are processed to yield sharpened lines. The method is then aplied to measurement of residual stresses in glass bar. The procedure is proved to be capable of extraction sharpened lines accurately from photoelastic multiplied fringes, and yields good experimental results consistently and precisely.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1387-1394
• /
• 2014

In a photoelastic experiment, it is necessary to know the material stress fringe constant of the photoelastic specimen to determine the stresses from the measured isochromatic fringe orders. The material stress fringe constant can be obtained using a simple tension specimen and/or a circular disk under diametric compression. In these methods, there is generally a need to apply numerous loads to the specimen in response to the relationship of the fringe order. Then, the least squares method is used to obtain the material constant. In this paper, the fringe orders that appear on a four-point bending specimen are used to determine the fringe constant. This method requires four photoelastic fringes obtained from a circular polariscope by rotating the analyzer to 0, ${\pi}/4$, ${\pi}/2$, and $3{\pi}/4$ radians. Using the four-point bending specimen to determine the material stress fringe constant has an advantage because measurements can be made at different locations by applying a constant load. The stress fringe constant measured with this method is within the range suggested by the manufacturer of the photoelastic material.