• Journal of the Korean Society of Systems Engineering
• /
• v.5 no.2
• /
• pp.49-56
• /
• 2009

KC-100(KAI Civil Aircraft, Small Series) aircraft is 4 seats general aviation aircraft with single piston engine which is developing under FAA part 23 category by Korea Aerospace Industries(KAI) and will be a shadow program for civil aircraft safety infrastructure improvement. This aircraft will be the first civil aircraft developed in Korea meeting the Korean regulatory KAS Part 23 requirements. Type certification for KC-100 aircraft was applied at the second half of this year. The type certificate is expected to be issued after 3 years of design, prototype manufacturing, ground and flight tests. In this paper the system engineering process for civil aircraft was first reviewed. Next, the differences and similarities in the system development between military and civil aircraft were systematically examined using experiences for KAI military aircraft development program.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.530-536
• /
• 2010

In-flight icing is a critical technical issue for aircraft safety and, in particular, ice accretions on aircraft surfaces can drastically impair aerodynamic performances and control authority. In order to investigate icing effects on the aerodynamic characteristics of KC-100 aircraft, a state-of-the-art CFD code, FENSAP-ICE, was used. A main wing section and full configuration of KC-100 aircraft were considered for the icing analysis. Also, shapes of iced area were calculated for the design of anti-/de-icing devices. The iced areas around leading edge of main wing and horizontal tail wing were observed maximum 7.07% and 11.2% of the chord length of wing section, respectively. In case of wind shield, 16.7% of its area turned out to be covered by ice. The lift of KC-100 aircraft were decreased to 64.3%, while the drag was increased to 55.2%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.191-195
• /
• 2011

The airframe ground vibration tests were conducted on the KC-100 aircraft according to the regulation requirement, KAS 23.629(a)(2) and the modal characteristics for the target modes were measured. To make FE model tuning, a design sensitivity approach with engineering judgment was implemented using MSC/Nastran and Attune, a genetic algorithm based parameter optimization software. Based on the comparison between initial prediction and test results, design variables such as beam cross-sectional properties and spring stiffnesses were devised. As the results, the correlation of the FE model to the GVT results was made appropriately, meeting the goal of matching the target frequencies within 5%.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.79-87
• /
• 2023

To design a control law of an aircraft, an accurate aircraft dynamic model is required. To obtain an aerodynamic database (DB) to build a dynamic model, a large number of wind tunnel tests are typically required. However, when flight test data of target aircraft exist such as in the process of unmanned conversion of a manned aircraft, an aircraft dynamic model can be obtained through a parameter estimation method and a DB tuning procedure. This paper describes a nonlinear model construction process and a verification method for KC-100 OPV aircraft. Flight data compatibility analysis was performed to determine suitability of the estimation method application. Linear model estimation was performed using the maximum likelihood estimation method. Results of aerodynamic DB tuning process and verification applying the FFS standard to the nonlinear model constructed are presented.

• Aerospace Engineering and Technology
• /
• v.11 no.1
• /
• pp.7-18
• /
• 2012

Full-scale static test was introduced for the KC-100 aircraft which is domestic civil aircraft to be certified for the first time. Test requirement, test frame, and important test stystems such as loading system, counterbalance system, restraint system and jacking system are explained in detail. Especially, the way to satisfy compliance for the installation of test article and loading system is introduced by using check sheets for the installations. 15 Full-scale and 7 local test conditions were successfully completed and the test data was obtained.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.464-467
• /
• 2010

Ice accretion on aircraft surface in icing condition induces external shape changes that may result in a hazard factor for aircraft safety. In case of aircraft main wing with high lift equipment, ice accretion is observed around leading edge and flap. During the design phase, location of ice accretion and associated aerodynamic characteristics must be investigated. In this study, icing effects on aerodynamic characteristics of the main wing section of KC-100 aircraft are investigated using an Eulerian-based FENSAP-ICE code in various icing conditions.

• Journal of the Korean Society of Systems Engineering
• /
• v.6 no.1
• /
• pp.1-13
• /
• 2010

KC-100 is a 4 seats, single piston engine, civil aircraft whose type certificate is applied for KAS 23 (FAR 23) for the first time in Korea. Its system safety assessment and analysis have been conducted to meet the minimum safety requirement in KAS 23 and to verify the safety of equipment, system, and installation in accordance with the requirement of ${\S}$23.1309 and the guidelines in FAA AC 23.1309-1D and SAE ARP 4761. This safety assessment begins with the FHA (Functional Hazard Assessment) at aircraft and system level in preliminary design phase, and all of the safety assessment and analysis reports including the preliminary version of SSA (System Safety Assessment) have been prepared during detail design phase. The revised version of these safety reports will be approved by Airworthiness Authority through the ground and flight test phases. In this paper, the safety assessment requirement in ${\S}$23.1309, safety assessment guideline in AC 23.1309-1D, and safety assessment and analysis methods in ARP 4761 will be explained based on the application example for KC-100 development. The experience and knowledge of this system safety assessment for civil aircraft can be applied to commuter aircraft of FAR 23 class or large transport airplane of FAR 25 class.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.4
• /
• pp.51-57
• /
• 2011

The spin-up and the spring-back are most severe load cases in the aircraft landing gear design. These load cases are caused by reciprocal action of complex physical phenomenon such as the friction between a tire and ground, inertia of the rotation of a tire and the flexibility of a landing gear structure. Generally, the empirical formula or the theoretical formula is used to calculate the spin-up and spring-back load in the early stage of the development program of the aircraft landing gear. After the materialization of the design of a landing gear, spin-up and spring-back load are acquired by the free drop test. In this study, the spin-up and the spring-back load of the rubber shock absorber type KC-100 nose landing gear are calculated by the explicit finite element analysis. Through this analysis, more accurate and realistic spin-up and spring back loads could be applied to the early phase of the development of the aircraft landing gear.

• Journal of Aerospace System Engineering
• /
• v.14 no.5
• /
• pp.49-57
• /
• 2020

The KC-100 has completed civil type certification with the Ministry of Land, Infrastructure, and Transport, and is currently under development as an unmanned aerial vehicle as part of the Ministry of Land, Infrastructure, and Transport. The Certification Technology of small Unmanned Airplane system (CTsUA system), which is an unmanned KC-100, is being developed to enable the installation of heavy-duty mission equipment and long-time flight missions. This study investigated the process and results of analyzing various parameters such as aircraft weight, airspeed, flight altitude, required horsepower, and fuel consumption at each stage to construct a mission profile based on the operational concept of the CTsUA system. To maintain a maximum take-off weight of 3,600 lbs (1,633 kg), the analysis determined that the weight of the application equipment for the unmanned system should be kept below 80 lbs (36 kg).

• Journal of Aerospace System Engineering
• /
• v.7 no.2
• /
• pp.15-22
• /
• 2013

The conformity of propulsion system need to be evaluated thorough the flight test because it is an important part of the airplane to ensure the flight safety. In the small airplane development, the flight test according to KAS(Korean Airworthiness Standards) Part 23 is one of the ways to verify compliance in terms of satisfactory aircraft/engine/propeller integration. This thesis introduces means of verifying the compliance and test requirement of KAS Part 23 for the conformity of the propulsion system in small airplane. It also describes procedures and methods of propulsion system flight test through KC-100 airplane project.