• Journal of the Korean Institute of Rural Architecture
• /
• v.24 no.2
• /
• pp.45-52
• /
• 2022

Of the 17,106 domestic reservoirs(as of December 2020), 14,611 are older than 50 years, and these old reservoirs will gradually increase over time. The injection grouting method is most applied to the reinforcement method of the aging reservoir. However, the injection grouting method is not accurate in uniformity and reinforced area. An laboratory model test was conducted to evaluate the applicability of the deep mixing method, which compensated for these shortcomings, as a reservoir reinforcement method. As a result of calculating the hydraulic conductiveity for each method through the model test results, the injection grouting method was calculated as a hydraulic conductiveity value that was about 7.5 times larger than that of the deep mixing method. As a result of measuring the water level change in the laboratory model test, it was found that the water level change decreased in the injection method and deep mixing method compared to the non-reinforcement method. In addition, deep mixing method showed a water level change of about 15% based on 40 hours compared to the injection method, indicating that the water-reducing effect was superior to that of the injection method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.412-419
• /
• 2009

Large quantity of extra soils discharged from excavation site in Songdo area can be treated by hardening agents and utilized in surface stabilized layer overlying thick reclaimed soft soil deposit. Though surface layer stabilization method using cement or lime for very soft soils has been studied in recent years, but studies on moderately soft clayey silt has not been tried. The purpose of this research is to investigate optimum mixing condition for stabilizing Songdo marine soil with low plasiticity. The optimum mixing conditions of hardening agents with Songdo soil such as kind of agents, mixing ratio, initial water content and curing time are investigated by uniaxial compression test and laboratory vane test. The results indicate that strength increases with high mixing ratio and long curing time, while decreases drastically under certain water content before mixing. Finally, optimum mixing condition considering economic efficiency and workability with test results was proposed.

• Computers and Concrete
• /
• v.13 no.6
• /
• pp.781-798
• /
• 2014

Estimating the workability of self-compacting concrete (SCC) is very important both in laboratories and on construction site. A method using visual information during the mixing process was proposed in this paper to estimate the workability of SCC. First, fourteen specimens of concrete were produced by a single-shaft mixer. A digital camera was used to record all the mixing processes. Second, employing the digital image processing, the visual information from mixing process images was extracted. The concrete pushed by the rotating blades forms two boundaries in the images. The shape of the upper boundary and the vertical distance between the upper and lower boundaries were used as two visual features. Thirdly, slump flow test and V-funnel test were carried out to estimate the workability of each SCC. Finally, the vertical distance between the upper and lower boundaries andthe shape of the upper boundary were used as indicators to estimate the workability of SCC. The vertical distance between the upper and lower boundaries was related to the slump flow, the shape of the upper boundary was related to the V-funnel flow time. Based on these relationships, the workability of SCC could be estimated using the mixing process images. This estimating method was verified by three more experiments. The experimental results indicate that the proposed method could be used to automatically estimate SCC workability.

• Computers and Concrete
• /
• v.25 no.5
• /
• pp.433-445
• /
• 2020

A method is proposed in this paper to estimate the workability of self-compacting concrete (SCC) in different mixing conditions with different mixers and mixing volumes by recording the mixing process based on deep learning (DL). The SCC mixing videos were transformed into a series of image sequences to fit the DL model to predict the SF and VF values of SCC, with four groups in total and approximately thirty thousand image sequence samples. The workability of three groups SCC whose mixing conditions were learned by the DL model, was estimated. One additionally collected group of the SCC whose mixing condition was not learned, was also predicted. The results indicate that whether the SCC mixing condition is included in the training set and learned by the model, the trained model can estimate SCC with different workability effectively at the same time. Our goal to estimate SCC workability in different mixing conditions is achieved.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.861-863
• /
• 2003

The method of measurement for laboratory tests on noise emission from appliances and equipment used in water supply installations is specified in ISO 3822-1. This part of standard gives detailed descriptions for mounting and operating draw-off taps and mixing valves in such laboratory test. Draw-off taps and mixing valves are the most common kind of appliance used in water supply installations.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.2
• /
• pp.35-44
• /
• 2016

PET aggregates were produced by mixing heated PET flakes with frictional soils. Using these artificially-made PET aggregates, horizontal drain tests in the laboratory, pilot scale model tests were conducted for the evaluation of the drainage characteristics of PET aggregates. Laboratory horizontal drain tests were conducted under twenty different conditions varying mixing ratios and surcharged pressures. Moreover, by utilizing the aggregates with a mixing ratio producing the lowest variation in terms of permeability against applied load, large scale tests were performed. Reliability of the test results was evaluated from comparison with the results of the laboratory horizontal drain test.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.2
• /
• pp.1-12
• /
• 2016

In this study, laboratory mixture design test and field test were performed to evaluate applicability of eco-friendly binder material (CMD-SOIL) using desulfurized dust in deep cement mixing method (DCM). As a result of laboratory mixture design test, the uniaxial compressive strength of CMD-SOIL was up to 1.136 times bigger than slag cement by changing the water content, mixing rate, and W/B. Also, it had shown the strength up to 1.222 times bigger in shell content and up to 1.363 times in mixing of floating soil. As a result of field test, field strength/laboratory design criterion strength ratio (${\lambda}$) is shown 0.77. And this result was similar to earlier studies. From this result, CMD-SOIL can show the same efficiency compared with existing binder.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.5
• /
• pp.15-24
• /
• 2022

In order to improve dredged area, long time and high cost is needed because of bad engineering and physical conditions. And there is no suitable example of pipe mixing method at domestic site. Moreover, applicability and effectiveness of this method is uncertain and shows different results between site and laboratory test. In order to solve these problems, we determined proper grain size distribution and water content range using dredged soil and reformed material (standard sand & material controlling grain size distribution) in the laboratory test. As a result, we confirmed that coefficient of sediment consolidation is increased and there is an improvement about separation sedimentation. Undrained shear strength was derived by water content of reformed dredging soil through regression analysis of test results. We suggest the correlation equation for determining mixing ratio.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.793-808
• /
• 2009

This paper presents procedure and prediction method of internal and external stabilities when designing D.C.M, with main factors to be considered, such as chemical reaction of additive, physical properties of stabilized body and mixing strength. Results show that through case studies, a design unconfined compressive strength of stabilized body (hereafter referred to as 'compressive strength') directly depends on the quantity of cement, which is decided by laboratory test, and the compressive strength enormously affects internal and external stabilities. So laboratory mixing test to obtain the compressive strength for design allowable stress should be given careful considerations.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.3
• /
• pp.61-69
• /
• 2023

As global trade and maritime port environments change, the need to respond to larger and faster ships is increasing. Accordingly, new ports are being built around metropolitan cities such as Busan and Ulsan. In general, a compaction method using sand or gravel is applied to the construction of a new port. However, due to the lack of sand or gravel and the difficulty in securing economic feasibility due to the increase in unit price, the deep mixing method has recently been used. Therefore, in this study, CMD-SOIL using circulating resources was applied to the Ulsan area, and the applicability was determined by analyzing the laboratory mixing test and boring results at in-situ. As a result of the test, it was analyzed that it showed more than the design mixing strength, and it was possible to secure the similar performance as blast furnace slag cement. In addition, it was analyzed that the design standard strength can be sufficiently secured as a result of in-situ boring. Therefore, considering the field applicability in the Ulsan, it is judged that the use of CMD-SOIL is possible.