• The Journal of the Korean dental association
• /
• v.49 no.11
• /
• pp.670-678
• /
• 2011

Various sorts of dental devices for the dental treatment have been introduced and adopted during past several years. Dental Laser, among all devices, seems to be possible for applying to over the whole treatments and widely employed. Furthermore, this article is to introduce that Dental Laser is intended to care patients secured with the effectual treatment against Conventional procedures based upon its studies. The advantages of Dental Laser treatment-along with LLLT (Low Level Laser Therapy) effect, biostimulation effect, and minimal invasive technique - make the patients reduce their fear of the operation, lighten the inconvenience of post operation, and shorten the treatment period. In particular, it is worth considering that the use of laser-assisted therapies is associated with a marked reduction in the use of analgesics and anti-inflammatory medications compared with conventional procedures. This article is to state advantages and differences of Dental Laser treatment compared with Conventional procedures, and to emphasize to become well-acquainted with the precautions for safety and effective Dental Laser treatment. In case of operating Dental Laser with lack of the instructions, it will cause the unpredicted fatal results; therefore this treatment requires special care in its operation. Henceforward, it is anticipated that infinite treatment protocols will be introduced by applying Dental Laser, and this is to address the utilization of Dental Laser.

• Laser Solutions
• /
• v.16 no.2
• /
• pp.1-6
• /
• 2013

Picosecond lasers are a very effective tool for micromachining metals, especially when high accuracy, high surface roughness and no heat affected zone are required. However, low productivity has been a limit to broadening the spectrum of their industrial applications. Recently it was reported that in the micromachining of copper with a 1064nm picosecond laser, there exist the optimal pulse energy and repetition rate to achieve the maximum volume ablation rate. In this paper, we used a 515nm picosecond laser, which is more efficient for micromachining copper in terms of laser energy absorption, to obtain its optimal pulse energy and repetition rate. Theoretical analysis based on the experimental data on copper ablation showed that using a 515nm picosecond laser instead of a 1064nm picosecond laser is more favorable in that the calculated threshold fluence is 75% lower and optical penetration depth is 50% deeper.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.2
• /
• pp.34-39
• /
• 2010

In order to achieve and maintain dimensional accuracy in laser micro-machining, dominant parameters such as laser power and laser focus position need to be monitored and controlled real time. Also, in order to selectively machine multi-layered materials, the material being presently machined need to be recognized. This paper presents an auto-focusing (AF) module to keep laser focus on a large-area surface; a real-time laser power stabilizing module based on optical attenuation; and a laser-induced breakdown spectroscopy (LIBS) module. With these monitoring modules, position error in laser focus on a 4" silicon wafer was kept below $4{\mu}m$, initially $51{\mu}m$, and laser power stability of a UV laser source was improved from 1.6% to 0.3%. Also, the material transition from polyimide to copper in machining of FCCL (flexible copper clad laminate) was successfully observed.

• Current Optics and Photonics
• /
• v.4 no.3
• /
• pp.238-246
• /
• 2020

The heat distribution in crystals in a 2-㎛ acousto-optic Q-switched Tm:LuAG laser pumped by pulsed-laser-diode (pulsed-LD) intermittent-pumping technology was analyzed using COMSOL software. The thermal lensing effect of the Tm:LuAG crystal can be mitigated by pulsed-LD intermittent-pumping techniques. An experimental setup using this kind of approach achieved maximum output energy of 8.31 mJ, minimum pulse width of 101.9 ns, and highest peak power of 81.55 kW, reached at a Q-switched repetition rate of 200 Hz. It offers significant improvement of performance of the output laser beam, compared to pulsed-LD double-ended pumping technology at the same repetition rate.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.80-85
• /
• 2009

An experimental study of energy absorption and x-ray emission from ultrashort laser pulse irradiation of in-situ produced solid clusters has been performed. Silver clusters produced by a 30 mJ, 300 ps laser pulse were irradiated up to an intensity of $3{\times}10^{17}\;W/cm^2$ by a 70 mJ, 45 fs compressed laser pulse from the same Ti:sapphire laser. Absorption of the laser light exceeding 70% was observed, resulting in an x-ray yield (>1 keV) of ${\sim}60{\mu}J$ pulse. This may constitute a much simpler means of intense x-ray generation using ultrashort laser pulses as compared to the irradiation of structured / pre-deposited cluster targets, and it offers higher x-ray conversion efficiency than that from gas clusters and planar solid targets.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.3
• /
• pp.96-100
• /
• 2004

The Nd： YAG laser is commonly used throughout many fields such as accurate material processing, IC marking, semiconductor annealing, medical operation devices, etc., due to the fact that it has good thermal and mechanical properties and is easy to maintain. In materials processing, it is essential to vary the laser power density for specific materials. The laser power density can be mainly controlled by the current pulse width and pulse repetition rate. It is important to control the laser energy in those fields using a pulsed laser. In this paper we propose the constant-frequency current resonant half-bridge converter and monitoring of capacitor charging voltage. This laser power supply is designed and fabricated to have less switching loss, compact size, isolation with primary and secondary transformers, and detection of capacitor charging voltage. Also, the output stabilization characteristics of this Nd： YAG laser system are investigated. The test results are described as a function of laser output energy and flashlamp arc discharging constant. At the energy storage capacitor charges constant voltage, the laser output power is 2.3％ error range in 600[V].

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.327-332
• /
• 2020

Laser induced surface activation (LISA) technology requires refined selection of process variables to fabricate conductive microcircuits on a general polymer material. Among the process variables, laser mode is one of the crucial factors to make a reliable conductor pattern. Here we compare the continuous wave (CW) laser mode with the pulse wave (PW) laser mode through determination of the surface roughness and circuit accuracy. In the CW laser mode, the surface roughness is pronounced during the implementation of the conductive circuit, which results in uneven plating. In the PW laser mode, the surface is relatively smooth and uniform, and the formed conductive circuit layer has few defects with excellent adhesion to the polymer material. As a result of a change of laser mode from CW to PW, the value of Ra of the polymer material decreases from 0.6 ㎛ to 0.2 ㎛; the value of Ra after the plating process decreases from 0.8 ㎛ to 0.4 ㎛, and a tight bonding force between the polymer source material and the conductive copper plating layer is achieved. In conclusion, this study shows that the PW laser process yields an excellent conductive circuit on a polymeric material.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2004.10a
• /
• pp.22-28
• /
• 2004

Pit and rim formation on the Acrylonitrile Butadiene Styrene(ABS) plastic surface was evaluated after it was irradiated by $CO_2$ and Nd:YAG laser beams. Our results show that thermal effect floor was well observed at the outer wall of pit with $CO_2$ laser irradiated while it was not the case with Nd:YAG laser irradiated. Also the volume and depth of pit formation increase proportionally with the energy intensities of two laser irradiations, but there are significant differences in the slope, width, and FWHM of the Pit formation with two types of laser irradiations. This result shows that $CO_2$ laser irradiation leads to better cooling contraction effect while Nd:YAG laser irradiation induces better recoil pressure effect during the interaction between ABS plastic and laser beam irradiation. The shape of the laser marking could vary significantly depending on the traveling path of molten plastic during injection molding of ABS plastic. Therefore, the selection of material and molding process can have a great impact on the performance of optical storage media.

• Journal of the Optical Society of Korea
• /
• v.17 no.4
• /
• pp.323-327
• /
• 2013

A laser ultrasonic inspection system has the advantage of nondestructive testing. It is a non-contact mode using a laser interferometer to measure the vertical displacement of the surface of a material caused by the propagation of ultrasonic signals with the remote ultrasonic generated by laser. After raising the ultrasonic signal with a broadband frequency range using a pulsed laser beam, the laser beam is focused to a small point to measure the ultrasonic signal because it provides an excellent measurement resolution. In this paper, foreign materials are measured by a non-destructive and non-contact method using the laser ultrasonic inspection system. Mixed foreign material on the corroded part is assumed and the laser ultrasonic experiment is conducted. An ultrasonic wave is generated by pulse laser from the back of the specimen and an ultrasonic signal is acquired from the same location of the front side using continuous wave laser and Confocal Fabry-Perot Interferometer (CFPI). The characteristic of the ultrasonic signal of existing foreign material is analyzed and the location and size of foreign material is measured.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.32 no.2
• /
• pp.51-55
• /
• 2021

There are several lasers available for office-based or suspension microlaryngoscopy laser procedures in the treatment of laryngeal diseases. Each has advantages and disadvantages given the depth of penetration per unit of power, absorption in water, spectral absorption characteristics, mode of delivery, safety, and cost. It is important to note that while the proper selection of indication of treatment based on a laser wavelength is critical, of equal importance is selecting the appropriate power setting, focal length (or spot size), and time of exposure. The photoangiolytic lasers precisely target hemoglobin within the microcirculation of the highly vascularized tissue and may have better hemostatic effects and preservation of surrounding normal tissue than the CO₂ laser. Although the choice of laser is purely theoretical and cannot be accurately concluded which parameters of laser (wattage and pulse width) were best to use, photoangiolytic laser surgery is safe and effective for specific laryngeal lesions. In this review, indications for photoangiolytic laser procedures for various laryngeal diseases, laser settings and surgical techniques for specific laryngeal lesions including sulcus vocalis, laryngeal dysplasia, and recurrent respiratory papillomatosis will be introduced. Pros and cons of in-office laser surgery using photoangiolytic laser and flexible CO₂ laser will also be addressed.