• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.2
• /
• pp.7-12
• /
• 2010

Due to the extremely short interaction time (< $10\times10^{-12}$sec) between laser pulse and material, which enables the minimization of heat affection, ultrafast laser micro-machining has rapidly widened its applications. In this paper, the characteristics of ultrafast laser micro-machining have been reviewed and experimentally demonstrated in laser drilling of silicon wafer and in laser cutting of rigid PCB.

• Korean Security Journal
• /
• no.3
• /
• pp.385-405
• /
• 2000

In the Present thesis, at temps were to study with the study on the terror with laser weapons. Chapter I which sets out purpose, scope and method. Chapter II concerns the general definition of laser weapons. Chapter III explain at length overview about development of laser weapons. Chapter IV suggest the terror with laser weapons and the counterplan against it. It is followed by concluding observation made in chapter V. To we operated security systems effectively, these need to be regulated according to a security measures organizations, laser facilities and equipments, laser plan and protective force, laser operations and so forth.

• Laser Solutions
• /
• v.4 no.3
• /
• pp.40-44
• /
• 2001

Microbump formation during CO$_2$ laser texturing of glass substrates is examined in this paper. Experimental results show that different bump shapes (dome-shaped, with a central dimple, and with a peripheral rim) are generated depending on the laser fluence. A theoretical model for the process is suggested based on thermoelastic behavior but limited only to the dome-shaped bump. The dimensions (maximum height and base area) of the bump shows a logarithmic dependence on laser fluence as expected from the theory. Numerical computation reveals that the effect of thermal diffusion is not negligible for relatively long laser pulses.

• Journal of Korean Physical Therapy Science
• /
• v.7 no.2
• /
• pp.533-543
• /
• 2000

This study was designed to evaluate the analgesic effect of low power GaAsAl laser on the pain threshold of mechanical stimulation using different treatment points, acupuncture point (zusanli) and non-acupuncture points(back). Furthermore, we investigated the analgesic effect of low power GaAsAl laser using the different duration and intensity of laser in mechanical stimulation induced pain behavior. The results were summarized as follows: 1. The threshold of mechanical stimulation was significantly increased by GaAsAl laser stimulation into zusanli point after 15 and 30 min after laser stimulation(P<05). However, the laser stimulation into non-acupoint did not affect the pain threshold of mechanical stimulation. with dose dependent manner. 2. In order to investigate the analgesic effects of BV depending upon different intensities of laser stimulation, the experimental animals were divided into three groups: 3 mW treated group, 6 mW treated group and 10 mW treated group. The low power GaAsAl laser stimulation was applied into zusanli acupoint for 30 min with different intensity of laser stimulation. Six and ten mW of laser stimulation significantly increased the pain threshold of mechanical stimulation at 15 min after laser stimulation as compared to that of control group(P<.05). Moreover, the analgesic effect of 10 mW laser stimulation was maintained for 30 min after laser stimulation (P<.05). 3. Finally, we tested the analgesic effect of 10 mW laser stimulation using different duration such as 10 min, 30 min or 1 hr after application of mechanical stimulation. In 30 min treatment group, the pain threshold of mechanical stimulation was increased at 15min and 30min after laser stimulation(P<.05). However, laser stimulation for 60 min dramatically increased the pain threshold of mechanical stimulation at 0 min after laser stimulation and the analgesic effect of laser stimulation was observed until 1 hr after laser stimulation. In conclusion, these data apparently demonstrate that low power GaAsAl laser has analgesic effect on mechanical induced pain model in rats. In addition, the treated point, intensity and duration of laser stimulation should be concerned before clinical application for pain management purpose.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.136-141
• /
• 2015

Laser surface polishing is a polishing method for improving surface roughness using an integrated laser beam. Using a laser for surface polishing can improve the surface condition without physical contact or chemical action. Laser polishing has mainly been used to polish the surface of diamond or optical articles, such as lenses and glasses. Recently, diverse studies on laser polishing for metals have been conducted. The analytic study of laser surface polishing has been conducted with experimental trials for comparison, so that the proper conditions for laser polishing can be recommended. In this study, laser surface polishing was simulated in order to predict the heat-affected zone on the die steel depending on the power of the pulsed laser. The simulated results were verified by comparing them to those of the experimental trials. Through this study, therefore, the application of FEM to the selection of appropriate laser conditions could be possible.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.644-650
• /
• 2012

This paper show the 2kW fiber laser cutting properties of SS400. The study was comparison of traditional 4kW $CO_2$ Laser cutting and 2kW Fiber laser cutting characteristics for the application of Industrial 2D Laser Cutting Machine. The laser used in this investigation was an IPG YLU-2000 multi-mode Ytterbium Fiber machine with a maximum power of 2000W and a wave length of 1070 nm. The laser was used in its Continuous Wave (CW) mode with an approximately top hat beam intensity distribution. Fiber laser high quality cuts at a large range of speeds (ranging from 2000 to 3800 mm/min) which has been obtained for the 2.3mm Sheet of SS400. 2kW power Fiber laser cut was able to max. 20mm sheets of SS400 (speed range from 650 to 850 mm/min). Fiber laser cutting used in conventional hole nozzle could cut 12mm SS400 but used in special dual cutting nozzle could cut 20mm SS400.

• Laser Solutions
• /
• v.16 no.4
• /
• pp.17-23
• /
• 2013

The research for the development of roll-to-roll printing process is actively underway on behalf of the existing semiconductor process. The roll-to-roll printing system can make the electronic devices to low-cost mass production. This study is performed for developing the manufacturing technology of the printing roll used in the printing process of electronic devices. The indirect laser engraving technology is used to create printable roll and the printable roll is made out of the chrome coated roll after coating copper and polymer on the surface of steel roll, ablating the polymer on the surface of roll and etching the roll. The 3 dimensional laser scanner and roll rotating systems are constructed and the system control program is developed. We have used the fiber laser of 100 W grade, the 3 dimensional laser scanner and the 3 axes moving stage system with a rotating axis. We have found the optimal conditions by performing the laser patterning experiments and can make the minimum line width of $24{\mu}m$ by using the developed 3 dimensional laser scanner system.

• Journal of the Korean Society of Combustion
• /
• v.1 no.1
• /
• pp.75-82
• /
• 1996

Laser induced incandescence, LII, recently developed technique for measuring soot concentration in flames, can overcome most of limitations of conventional laser extinction measurement. In this study, experiments were performed to investigate the effect of laser intensity, detection wavelength, and also laser beam quality on both LII signal at a particular position and peak-to-centerline LII signal ratio. The results of LII signal with increasing laser intensity shows its near-independence of laser intensity once threshold level of laser intensity has been reached. However, this near-independence depends on laser beam quality and the incident optical setup. The peak-to-centerline LII signal ratio slowly but continuously increases with laser power. This fact is due to the dependence of LII signal on particle mean diameter. LII signal is attenuated during it passes through the flame containing soot particles. The attenuation rate is inversely proportional to detection wavelength. In this study, LII signal at 680 nm band is 10% greater than the signal at 400 nm band.

• Laser Solutions
• /
• v.17 no.4
• /
• pp.1-6
• /
• 2014

Femtosecond laser induced shock generation in water and vitreous humor of enucleated porcine eyeball was investigated. When focusing the femtosecond laser into the liquid mediums, the acoustic waves with a frequency of about 15.6kHz could be observed by using wide-band microphone. The amplitude of the acoustic signals from water has attained a maximum under a laser power of about 5mW. Further increment of the power results in a decrement of the acoustic signals due to nonlinear optical process including filamentation of laser beam. We have further investigated the effect of femtosecond laser induced acoustic waves by applying the laser pulse into enucleated porcine eyeball. The comparative studies on both healthy and diseased eyeballs led us propose that the femtosecond laser pulses could be utilized as a novel tools for treatment of partially detached retina layers from their choroid structures.

• Laser Solutions
• /
• v.8 no.1
• /
• pp.27-37
• /
• 2005

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two poles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets.