• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.332-340
• /
• 2002

The light guide plate of the TFT-LCD reflects the light originated from the light source, and guides the light to the front side of LCD so that we can see images vividly. This paper is concerned with tile injection molding of the light guide plate for the reflective typed LCD related to IMT-2000. The finite element analysis has been carried out based on the pine stress theory to predict both the thermal stresses of the products in the post-filling stage and the in-plane deformation behavior of the products after ejection process. Based on the simulation results, the mold for the light guide plate of a 2inch sized LCD has been designed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.693-696
• /
• 2009

The ray-tracing technique was used to optimize the light guide plate for the purpose of improving the on-axis luminance on the edge-lit backlights. One-dimensional prisms and engraved V-shaped patterns were applied to the upper and the lower surfaces of the light guide plate, respectively. By optimizing the apex angles of these micro-structures, as well as the shape of the reverseprism film put over the light guide plate, highly-collimated light-output distribution could be obtained on the backlight, which may contribute to the development of mobile LCD's with low power consumption.

• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.341-348
• /
• 2002

For the light guide plate of the TFT-LCD, there have been increasing demands for higher brightness, thin and light-weight design, and lower power consumption. To meet these demands, a micro-prism-type frontlight that integrates a prismatic sheet and a light-guiding plate has been developed. In this paper, the influences of processing conditions on the brightness were studied lot the injection molding of the light guide plate. Based on the experiment with an actual mold, the design of experiments and the neural network theory were used lot choosing the optimal processing parameters to increase the brightness and the uniformity. The verification experiment also showed that the brightness and the uniformity were increased dramatically with the chosen processing conditions.

• Korean Journal of Optics and Photonics
• /
• v.31 no.4
• /
• pp.176-182
• /
• 2020

The possibility of replacing the condensing-prism film used in conventional backlight units with a light-guide plate engraved with a submicrometer-periodic diffraction grating was investigated. The optimal period for the diffraction grating was determined through simulation and experiment, and the transmission-mode efficiency of the diffraction grating was calculated in terms of the polar angle and azimuthal angle of the incident light. In addition, the effects of the two methods of optimizing the polar angle and the directional angle were compared by simulation, by suggesting the shape and configuration of the light-guide plate, so that more light could be extracted by diffraction. By using a ray-tracing program, the luminance angular distribution of the light-guide plate engraved with the diffraction grating was calculated and compared to the luminance angular distribution for each actual prototype.

• IEIE Transactions on Smart Processing and Computing
• /
• v.6 no.2
• /
• pp.124-128
• /
• 2017

A light guide improves the spatial resolution of a gamma ray imaging system by diffusing the scintillation light. Similarly, light diffusion film, which has been applied to flat-panel-display engineering, spreads the light from the light guide panel. In this study, we adopted light diffusion film for the light guide of a gamma ray imaging system, and evaluated its diffusion characteristics. We compared the light diffusion performance of the film to an ordinary acrylic plate. As a result, the diffusion film widely spreads scintillation light. As for the thickness of the light guide, we acquired more distinct images with three films overlapped than with an acrylic plate. We expect light diffusion film to be a promising candidate for light guides in gamma ray imaging systems.

• Transactions of Materials Processing
• /
• v.21 no.2
• /
• pp.126-130
• /
• 2012

Accurate optical texturing of light guide plate over the entire surface area is an important technical issue in LCD TV industry. Injection molding process has the potential to produce large light guide plates having highly efficient optical textures such as micro-prism array. This study is focused on the effect of the degree of replication of the micro texture of the 40" injection molded light guide plates on the overall optical performance of the display panel. Measured replication ratios of the micro-textures formed with three different types of injection molding process were considered in the modeling of prismatic micro segment array. Optical simulation was conducted and results were discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1609-1612
• /
• 2005

The effects of injection molding conditions on the uniformity and brightness of light guide plate(LGP) with micro-patterns were investigated in the present study. An injection molding system for stampers with mirco-pattern was designed and manufactured to perform experiment. Variations of injection molding speed, mold and melt temperature for LGP were considered in this work. Also, injection molding characteristics of LGP were investigated by numerical analysis using plastic injection molding commercial code. It was shown that injection molding conditions such as injection speed, melt temperature and mold temperature can have an effect on the uniformity and brightness of light guide plate.

• Journal of Information Display
• /
• v.5 no.1
• /
• pp.7-15
• /
• 2004

A highly simplified backlight unit mainly composed of diffractive grating in sub-micron order imprinted light-guide plate (LGP) is proposed for edge-lit backlight unit. Optical characteristics of the imprinted LGP are examined by RCWA and the performance is verified through Monte Carlo simulation. Results show that the diffraction efficiency, luminous flux and its uniformity over the area are significantly affected by the angle of incident ray. Consequently couples of design considerations are additionally proposed to enhance luminous flux. In terms of peak luminance and out-coupling luminous flux, the experimental results are agreed well with the performance simulation. Finally, compared with optical characteristics of conventional backlight unit, we could conclude that the proposed simplified backlight unit made of diffractive grating imprinted light-guide plate is a good substitute for the conventional backlight unit.

• Journal of the Optical Society of Korea
• /
• v.19 no.2
• /
• pp.159-164
• /
• 2015

In the injection-molded light guide plate the replication quality, i.e. the reproduction accuracy, of micro-patterns should be high and uniform over the entire surface area. However technical difficulty in meeting the necessary replication quality arises as the plate size becomes large for TV applications. We propose a simulation technique to optimize the distribution of micro-patterns on a 55-inch injection molded light guide plate considering non-ideal replication quality of micro-patterns. The luminance uniformity could be improved by more than 16% by optimizing the pattern distribution in spite of the same replication quality.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.291-292
• /
• 2008