• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.27-36
• /
• 2014

This paper presents an adaptive wide-area damping controller (WADC) based on generalized predictive control (GPC) and model identification for damping the inter-area low frequency oscillations in large-scale inter-connected power system. A recursive least-squares algorithm (RLSA) with a varying forgetting factor is applied to identify online the reduced-order linearlized model which contains dominant inter-area low frequency oscillations. Based on this linearlized model, the generalized predictive control scheme considering control output constraints is employed to obtain the optimal control signal in each sampling interval. Case studies are undertaken on a two-area four-machine power system and the New England 10-machine 39-bus power system, respectively. Simulation results show that the proposed adaptive WADC not only can damp the inter-area oscillations effectively under a wide range of operation conditions and different disturbances, but also has better robustness against to the time delay existing in the remote signals. The comparison studies with the conventional lead-lag WADC are also provided.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.7
• /
• pp.1255-1262
• /
• 2009

The present study explained the phenomenon that low frequency oscillation is synchronized with discrete data obtained from a wide area system, and a sync search method. When a disturbance occurs in an power system, various controllers operate in order to maintain synchronization. If the system's damping is poor, low frequency oscillations continue for a long time and the oscillations are synchronized with one another at specific frequency. The present study estimated dominant modes, magnitude and phase of signals by applying parameter estimation methods to discrete signals obtained from an power system, and performed sync search among wide area signals by comparing the estimated data. Sync search was performed by selecting those with the same frequency and damping constant from dominant oscillation modes included in a large number of signals, and comparing their magnitude and phase. In addition, we defined sync indexes in order to indicate the degree of sync between areas in a wide area system. Furthermore, we proposed a wide area sync search method by normalizing mode magnitude in discrete data obtained from critical generator of the wide area. By applying the sync search method and sync indexes proposed in this study to two area systems, we demonstrated that sync scanning can be performed for discrete signals obtained from power systems.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.6
• /
• pp.1105-1112
• /
• 2022

Field data monitoring systems such as renewable energy generation and smart farm integrated control are developing from PC and server to mobile first, and various wireless communication and application services have emerged with the development of IoT technology. Low-power wide-area networks are services optimized for low-power, low-capacity, and low-speed data transmission, and data collected in the field is transmitted to designated storage servers or cloud-based data platforms, enabling data monitoring. In this paper, we implement an IoT repeater that collects field data with a single device and transmits it to a wireless carrier cloud data flat using a low-power wide-area network, and a monitoring app using it. Using this, the system configuration is simpler, the cost of deployment and operation is lower, and effective data accumulation is possible.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.75-76
• /
• 2016

This paper proposes a power factor correction circuit with a high efficiency over a wide load range characteristics for a communication power supply. And the characteristic verification is applied to produce a design of prototype. Power factor correction circuit can reduce conduction losses by applying Bridgeless Boost Converter for efficiency. Over a wide load range to maintain the efficient, the control method of a PWM controller is divided by two sections according to the load area. In the low-load region, it was reduced switching losses by applying the critical conduction mode control method. On the other hand, in the heavy-load area, the hysteresis current control method is used to maintain the high efficiency over a wide load range by limiting the peak noise of the inductor.

• Journal of KIISE
• /
• v.44 no.7
• /
• pp.733-741
• /
• 2017

LPWAN(Low Power Wide Area Network) technology is M2M (Machine to Machine) networking technology for the Internet of Things. The technology is designed to support low-power, long-distance and low-speed communications that are typical of LoRaWAN(Long Range Wide Area Network). To exchange inter-object information using a LoRaWAN, the link performances for various environments must be known. however, active performance analysis research that is based on an empirical environment is nonexistent. Therefore, this paper empirically evaluates the performance of the LoRa (Long Range) link, a physical communication technology of the LoRaWAN for various variables that may affect the link quality in indoor and outdoor environments. To achieve this, a physical performance monitoring system was designed and implemented. A communication experiment environment was subsequently constructed based on the indoor and outdoor conditions. The SNR(Signal to Noise Ratio), RSSI(Received Signal Strength Indication), and the PDR(Packet Delivery Ratio) were evaluated.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.2
• /
• pp.239-250
• /
• 2022

LoRa is a physical layer technology designed to secure highly reliable long-range communication with introducing loco parentis tree network and chirp spreading spectrum. Since since a leaf can send message to more than one parents simultaneously with a single transmission in a region, packet delivery ratio increases logarithmically as the number of gateways increases. The delivery ratio, however, dramatically collapses even under loco parentis tree topology due to the limitations of ALOHA-like primitive MAC, . The proposed method is intended to exploit SDMA approach to reuse frequency in an area. With the view, TxPower of each sender for each message in a concurrent transmission is elaborately controlled to survive the collision at different gateway. Thus, the gain from the capture effect improves the capacity of resource-hungry Low Power and Wide Area Networks.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.1-10
• /
• 2018

Wide-area monitoring of tree-related high impedance fault (THIF) efficiently contributes to increase reliability of large-scaled network, since the failure to early location of them may results in critical lines tripping and consequently large blackouts. In the first place, this wide-area monitoring of THIF requires managing the placement of sensors across large power grid network according to THIF detection objective. For this purpose, current paper presents a framework in which sensors are distributed according to a predetermined risk map. The proposed risk map determines the possibility of THIF occurrence on every branch in a power network, based on electrical conductivity of trees and their positions to power lines which extracted from spectral data. The obtained possibility value can be considered as a weight coefficient assigned to each branch in sensor placement problem. The next step after sensors deployment is to on-line monitor based on moving data window. In this on-line process, the received data window is evaluated for obtaining a correlation between low frequency and high frequency components of signal. If obtained correlation follows a specified pattern, received signal is considered as a THIF. Thereafter, if several faulted section candidates are found by deployed sensors, the most likely location is chosen from the list of candidates based on predetermined THIF risk map.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.533-534
• /
• 2008

This paper presents a multi-phase ring VCO for low-cost, low-power GPS receiver. In the RF band used in GPS, L1 band is now in commercial-use and L2,L5 are predicting to be commercial-use soon. Thus Wide band PLL and Cost-effective IC solutions are required for future multi-band GPS receiver that received three types band at once. A new PLL architecture for multi-band GPS application is proposed. Ring VCO is even smaller than LC-VCO and a good alternative for low-cost solution. Proposed multi-phase ring VCO offers wide frequency range covering L1, L2, and L5 band, 20% reduction of area, 23% reduction of PLL power and can generate I/Q without extra I/Q generator.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.5
• /
• pp.141-148
• /
• 2009

Wireless Sensor Networks (WSN) can be applied to various industry fields and environment analysis fields with the progress of various sensor technologies. Also WSN help automatically monitoring of sensor nodes installed at wide area. Especially, the tiny sensor nodes recently developed for the environment analysis require much more electronic power. The reasons are the measurable fields are departmentalized and the more detailed measuring fields are created by the development of various materials and applications. Furthermore, the sensor nodes operated by small batteries for the fields require low cost and low power consumption in wireless networks technology. The power efficiency is the most important factor for the WSN life time. Because the sensor nodes are installed at wide area and hard to recover. This paper proposes the WSN algorithm is applied sensor node that has low power consumption and efficiency measurement.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2017.06a
• /
• pp.143-144
• /
• 2017

다양한 응용 매체의 유비쿼터스(ubiquitous) 연결을 위한 사물 인터넷 (Internet-of-Thing; IoT) 시스템은 저전력 광역 통신 (Low Power Wide Area; LPWA) 기술을 기반으로 한다. 저전력 광역 통신 시스템의 충족조건인 전송 거리 확대와 낮은 전력 사용은 시스템 전력 운용 관점에서는 상호 충돌하는 조건이다. 이를 위해 신호대역폭을 줄여 수신기 감도 (receiver sensitivity) 를 개선하는 초협대역 (Ultra Narrow Band; UNB) 기술이 주목받고 있다. 여기서는 이러한 저전력 광역 통신을 위한 초협대역 변조 기술의 신호 대 잡음 비(Signal-to-Noise Ratio; SNR)에 대해 분석한다.