• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.46-54
• /
• 2000

In this paper, PIFA on PCS handset for SAR reduction is designed. According to the position of PIFA attached on the handset, side mounted PIFA and top mounted PIFA are suggested. Resonance characteristics with variety of design parameters are analyzed. And monopole antenna with $\lambda$/4 length is designed and compared with PIFAs in bandwidth and SAR. At 1.83 GHz center frequency, the bandwidth of side mounted PIFA and monopole antenna are 8.2% and 21.7%, respectively. The 1 g and 10 g peak average SARs of side mounted PIFA are 0.686 and 0.353 respectively, which are about 1/3 of SARs of monopole antenna, 1.759 and 0.978, respectively.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.135-140
• /
• 2008

In this paper, the spiral antenna with the center frequencies of 315MHz, 433MHz, and 447MHz for RKE system of a vehicle is designed on PCB. The antenna is microstrip line-fed, and applied PIFA concept near the feeding part to easily tune center frequency and input impedance. The PIFA-type spiral antenna with the size of $30mm{\times}20mm$ is designed on printed PCB by considering the effect of circuits and components on PCB, ECU case and vehicle body. Also chip inductor inserted dual-band spiral antenna of 315MHz and 447MHz is designed. We found that the antenna designed on PCB satisfied the antenna specifications through measurement and field test.

• ETRI Journal
• /
• v.28 no.2
• /
• pp.216-218
• /
• 2006

This letter presents the design for a low-profile planar inverted-F antenna (PIFA) that can be stuck to metallic objects to create a passive radio frequency identification (RFID) tag in the UHF band. The designed PIFA, which uses a dielectric substrate for the antenna, consists of a U-slot patch for size reduction, several shorting pins, and a coplanar waveguide feeding structure to easily integrate with an RFID chip. The impedance bandwidth and maximum gain of the tag antenna are about 0.3% at 914 MHz for a voltage standing wave ratio (VSWR) of less than 2 and 3.6 dBi, respectively. The maximum read range is about 4.5 m as long as the tag antenna is on a metallic object.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.985-997
• /
• 1999

In this paper, the detection of 1 g and 10 g averaged SAR on human head caused by PCS handheld phones is analyzed and discussed. Conventional monopole antenna and planar structured PIFA are used in the computational model to apply to the antennas mounted on handheld phone. These antennas are designed to operate in the near of frequency 1.8 GHz, human head model is sampled to have cell size 1.5 mm and sloped to front direction by 30$^{\circ}$. It is found that, when monopole antenna is applied, 1 g averaged SAR is 1.4 W/kg, 10 g averaged SAR is 0.7 W/kg, when PIFA is applied, for each case, SARs are 1.143 W/kg, 0.4866 W/kg. While the radiation pattern of the monopole antenna is symmetrical, that of planar structured antenna is asymmetrical and SAR caused by PIFA is less than SAR by the monopole antenna. The radiation efficiency of PIFA is 62.6%, which is higher than that of monopole, 53%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3608-3613
• /
• 2009

In this paper, we propose a mobile Radio Frequency Identification antenna for mobile hand set. The proposed antenna with directive radiation characteristics based on combination of electric-magnetic radiators can be installed in the mobile hand-set. The combination of PIFA antenna for electric radiator and loop antenna for magnetic radiator is presented and designed for료 m-RFID reader system. Target frequency band is 900-MHz band. and desired gain is 4dBi. The antenna is simulated using Ansoft HFSS software and shows expected results. The antenna is also manufactured using FR4-epoxy circuit board (h=1 mm, $\varepsilon_{\tau}=4.4$). There are good agreements between the simulated and measured VSWR curves and radiation characteristics.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.768-772
• /
• 2007

Integration of RF front end module(FEM) into the antenna has been investigated in USPCS band (1.88GHz-1.99GHz). The FEM consists of input filter, power amplifier, coupler, power detector, bias switch and duplexer. The antenna was designed in planar inverted F antenna(PIFA) structure to implement it inside the handset. In order to avoid strong coupling between the antenna and FEM, a shielding ground layer was placed between them. The antenna size is 19mm by 10mm by 6mm under which FEM whose size is 8mm by 5mm by 1.5m locates. The antenna impedance was selected to match to FEM having better efficiency rather than gain since FEM has enough gain whose system spec is minimum of 20dB. The antenna patterns are shown with and without FEM.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1107-1115
• /
• 2011

In this paper, a headset multiple-input multiple-output(MIMO) antenna for on-body application is proposed and the antenna performance with body effect and the impact on human body are investigated. The proposed MIMO antenna is composed of two planar inverted-F antennas(PIFA) above ground plane and an isolator located between the two antennas enhance the isolation characteristic. Simulation was carried to analyze the effect of human body on antenna performance when a human body is located in the near field of the antenna. According to the measurement result, the diversity performance of the proposed antenna can be considered good since ECC(Envelope Correlation Coefficient), which commonly indicates the performance of a MIMO antenna, remains below 0.1 over the ISM band. The measured SAR values for antennas 1 and 2 are 0.575 W/kg and 0.571 W/kg, respectively when 250 mW input power in engaged. These values satisfy the FCC guideline which states that the 1-g average SAR should be lower than 1.6 W/kg.

• Journal of KIISE:Information Networking
• /
• v.35 no.2
• /
• pp.120-129
• /
• 2008

The purpose of sensor network is gathering the information from sensor nodes. If there are selfish node that deliberately avoid packet forwarding to save their own energy, the sensor network has trouble to collect information smoothly. To solve this problem we suggest a mechanism which uses credit payment schema according to the amount of forwarding packets. Sensor nodes use credits to send their own message and they forward packets of other sensor nodes to get credits. To offer authenticity we combined the roles of sink node and server, also we used piggybacking not to send additional report message. The packet trace route is almost fixed because sensor node doesn't have mobility. In this case, it happens that some sensor nodes which don't receive forwarding packets therefore they can't get credit. So, we suggested the way to give more credits to these sensor nodes. Finally, we simulated the suggested mechanism to evaluate performance with ns2(network simulator). As a result, packet transmission rate was kept on a high rate and the number of arrival packets to sink node was increased. Also, we could verify that more sensor nodes live longer due to deceasing the energy consumption of sensor nodes.