• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.3
• /
• pp.101-104
• /
• 2004

It was realized that MC-XRD is useful for phase analyzing of inclusions in crystals because it can focus the X-Ray beam to the small particles sized dozens of $\mu\textrm{m}$ with high S/N ratio. By using this MC-XRD, needle-like inclusions which are seen generally in corundum crystals known as rutile was found to be the iron titanium oxide and iron oxide which has the chemical composition of $Fe_2TiO_4,\; Fe_2TiO_5,\; Fe_2O_3$respectively

• Advances in materials Research
• /
• v.4 no.3
• /
• pp.133-144
• /
• 2015

The aim of this investigation is to prepare geopolymer resin by alkali activation of ceramic waste (AACW) with different sodium hydroxide (NaOH) and liquid sodium silicate (LSS) concentrations. In order to prepare geopolymer cement, AACW was replaced by 10 and 30 % by weight (wt.,) of concrete waste (CoW) as well as 10 and 30 wt., % ground granulated blast-furnace slag (GGBFS). The results showed that, the compressive strength of AACW increases with the increase of activator content up to 15:15 wt., % NaOH: LSS. All AACW hardened specimens activated by 3:3 (MC6), 6:6 (MC12), 12:12 (MC24) and 15:15 wt., % (MC30) NaOH: LSS destroyed when cured in water for 24h. The MC18 mix showed higher resistivity to water curing. The results also showed that, the replacement of AACW containing 9:9 wt., % NaOH: LSS (MC18) by 10 (MCCo10) and 30 (MCCo30) wt., % CoWdecreased the compressive strength at all ages of curing. In contrast, the MCCo10 mix showed the lower chemically combined water content compared to MC18 mix. The MCCo30 mix showed the higher chemically combined water content compared to MC18 and MCCo10 mixes. The compressive strength and chemically combined water of all AACWmixes containing GGBFS (MCS10 and MCS30) were higher than those of AACWwith no GGBFS (MC18). As the amount of GGBFS content increases the chemically combined water increases. The x-ray diffraction (XRD) proved that as the amount of CoWcontent increases, the degree of crystallinity increases. Conversely, the replacement of AACW by GGBFS leads to increase the amorphiticity character. The infrared spectroscopy (FTIR) confirms the higher reactivity of GGBFS compared to CoW as a result of successive hydration products formation, enhancing the compaction of microstructure as observed in scanning electron microscopy (SEM).

• 한국전기화학회:학술대회논문집
• /
• 2002.11a
• /
• pp.45-56
• /
• 2002

• Korean Journal of Materials Research
• /
• v.13 no.1
• /
• pp.24-30
• /
• 2003

The Raney Ni catalyst was fabricated by mechanochemically process(MC process) in the Al-Ni system. Intermetallic compound obtained by mechanical alloying was leached in an alkaline solution. The characteristics of the mechanically alloyed powder and Raney Ni catalyst were analyzed by XRD, ICP-AES and EXAFS. In Al-50wt.%Ni, the metastable intermetallic compound phase close to AlNi phase was obtained by mechanical alloying unlike Al-Ni equilibrium phase diagram. The metastable intermetallic compound was transformed into $Al_3$$Ni_2$phase via the annealing at $750^{\circ}C$. The microstructure of Raney Ni fabricated by MC process was mainly bcc Ni including fcc Ni.

• Computers and Concrete
• /
• v.13 no.6
• /
• pp.695-707
• /
• 2014

This study investigated the chloride binding isotherms of various cement types, especially the contributions of C-S-H and AFm hydrates to the chloride binding isotherms were determined. Ordinary Portland cement (OPC), Modified cement (MC), Rapid-hardening Portland cement (RHC) and Low-heat Portland cement (LHC) were used. The total chloride contents and free chloride contents were analyzed by ASTM. The contents of C-S-H, AFm hydrates and Friedel's salt were determined by X-ray diffraction Rietveld (XRD Rietveld) analysis. The results showed that OPC had the highest chloride binding capacity, and, LHC had the lowest binding capacity of chloride ions. MC and RHC had very similar capacities to bind chloride ions. Experimental equations which distinguish the chemically bound chloride and physically bound chloride were formulated to determine amounts of the bound chloride basing on chloride binding capacity of hydrates.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.2
• /
• pp.69-75
• /
• 2008

Electrochemical behaviors of surface modified and MC3T3-E1 cell cultured Ti-30Ta alloys have been investigated using various electrochemical methods. The Ti alloys containing Ta were melted by using a vacuum furnace and then homogenized for 6 hrs at $1000^{\circ}C$. MC3T3-E1 cell culture was performed with MC3T3-E1 mouse osteoblasts for 2 days. The microstructures and corrosion resistance were measured using FE-SEM, XRD, EIS and potentiodynamic test in artificial saliva solution at $36.5{\pm}1^{\circ}C$. Ti-Ta alloy showed the martensite structure of ${\alpha}+{\beta}$ phase and micro-structure was changed from lamellar structure to needle-like structure as Ta content increased. Corrosion resistance increased as Ta content increased. Corrosion resistance of cell cultured Ti-Ta alloy increased predominantly in compared with non cell cultured Ti- Ta alloy due to inhibition of the dissolution of metal ion by covered cell. $R_p$ value of MC3T3-E1 cell cultured Ti-40 Ta alloy showed $1.60{\times}10^6{\Omega}cm^2$ which was higher than those of other Ti alloy. Polarization resistance of cell-cultured Ti-Ta alloy increased in compared with non-cell cultured Ti alloy.

• Journal of Powder Materials
• /
• v.3 no.3
• /
• pp.181-187
• /
• 1996

Cobalt and VC powders were ball milled with M2 grade high speed steel powders under various ball to powder ratios. The powders milled under higher ball to powder ratio become finer, more irregular and have a broader size distribution, and thus possess a lower compressibility and a better sinterability regarding densification. Increasing the ball to powder ratio lowered the sintering temperature to obtain the density level necessary to isolate all the pores. Lowering the sintering temperature is very critical to maintain fine microstructure since grain and carbide coarsening are accelerated by higher sintering temperature due to more liquid phase formation. The powders obtained by ball milling at 20 to 1 ratio has the lowest compressibility but has the best sinterability, almost compatible to unmilled pure M2 powders. A sintered body over 97% theoretical density with fine microstructures having average grain size of ~10 microns was obtained from the powder by sintering at 1260 $^{\circ}C$ for 1 hour in vacuum. XRD results indicate that two types of carbides are mainly present in the sintered structure, MC and $M_{6}C$ type. The MC type carbides are more or less round shaped and mainly located at the grain boundaries whereas the $M_{6}C$ type are angular shaped and mainly located inside the grains.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.615-621
• /
• 1999

The new process in order to fabricate of Ni catalyst with high activity by the mechanochemical(MC) method which was combined the mechanical alloying(MA) and the chemical treatment process. The microstructure and characterization of mechanically alloyed Ni-5-wt% Al powder and Ni catalyst gained by alkali leaching were investigated byt he various analysis such as XRD, SEM-EDS, HRTEM and laser particle analyzer. The steady state powder with 1~2$\mu\textrm{m}$ mean particle size was obtained after 30hr milling with the PCA of 2 wt% stearic acid under the condition of grinding stainless steel ball to powder ratio of 60:1 and rotating speed fo 300rpm. According to result of HRTEM diffraction pattern, MA powder of the steady state was nanocrystalline $Al_3$$Ni_2$ intermetallic compound. Ni catalyst was obtained after KOH leaching of the steady state powder was about 20nm nanocrystalline which contained about 8 wt % Al.

• Journal of Powder Materials
• /
• v.4 no.3
• /
• pp.222-229
• /
• 1997

A P/M high speed steel of ASP 30 grade was austenitized, gas quenched and tempered at various conditional. The mechanical properties such as hardness, bend strength and fracture toughness were evaluated after heat treatment. The microstructure and the type and volume fraction of carbides were analyzed by an optical microscope, image analyzer and XRD. The primary carbides after the heat treatment were MC and $M_6C$ type. The volume of the total carbide varied from 10 to 15% depending on the austenitizing and tempering temperature. The tempering temperature for maximum hardness was at around 52$0^{\circ}C$. But the maximum bend strength was obtained at about 55$0^{\circ}C$. The fracture toughness was largely affected by the presence of retained austenite after gas quenching and secondary hardening during tempering.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.6
• /
• pp.547-554
• /
• 2010

In this study, new manganese oxide (i.e., black-birnessite) particles with nanostructures were prepared and its physico-chemical properties and oxidative-transformation efficiency on 1,4-naphthoquinine(1,4-NPQ) in the presence of reactive mediator was investigated. The results were also compared with that of the manganese oxide (i.e., brown-birnessite) particles synthesized by classical McKenzie method. Analysis of XRD and SEM data show that the particles are a single phase corresponding to a birnessite-based manganese oxide with cotton ball-like shapes containing nanofibers. In batch experiments, removals of 1,4-NPQ by the black-birnessite follows pseudo-first-order kinetics and the rate constant values obtained are greater about 2.3 times than that of the brown-birnessite in spite of its lower surface area (41.0 vs 19.80 $m^2/g$). The results can be explained by the higher crystallinity and nano structured features of the back-birnessite particles, which give higher reactivity for the removals of the quinone compound. HPLC analysis of the reaction products confirmed that the balck-birnessites removed 1,4-NPQ through cross-coupling reaction in the presence of catechol as a reactive mediator.