• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.132-138
• /
• 2014

The use of AGVs(Automated Guided Vehicles) are increasing in many factories. The most widely used AGV system is that magnetic tapes are attached on the factory floor to make guided path and an AGV equipped with a magnetic sensor follows the path by sensing magnetic flux. In this AGV system, usually a magnetic sensor is attached on the front end of an AGV to detect the guided path and the sensor generates analog voltages proportional to the magnetic flux. The problem is that the AGV in use has rather big tracking errors because the accurate orientation of the AGV can not be detected by using only one magnetic sensor. In this paper, we propose a method to minimize the path tracking errors. In our method, one additional sensor is attached on the rear end of the AGV to estimate the orientation of the AGV and to control more accurately the AGV according to the estimated orientation of the AGV. We performed several experiments and the results successfully show the feasibility of the proposed method.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.1151-1158
• /
• 2011

Proximity magnetic sensor is able to detect the object target accurately in close range and it has been widely used in the underwater guided weapon system because there is no countermeasures from the target. In order to increase the damage of target by shock wave due to explosion of the underwater guided weapon system, the maximum detection range of the proximity magnetic sensor needs to be increased. In this paper, we describe the techniques of the optimum transmitting and receiving coils design using the Finite Element Method for the output power enhancement of the transmitter and the sensitivity improvement of the receiver. Finally, the proposed design techniques of the transmitter and the receiver were verified using a experimental setup and a prototype.

• Journal of the Korean Magnetics Society
• /
• v.23 no.5
• /
• pp.159-165
• /
• 2013

A active magnetic sensor has been widely used in the underwater guided weapon system because it is able to detect a target accurately in close range, but the target doesn't have any good countermeasure to overcome the threat from the active magnetic sensor. Recently, in order to increase the damage area of target by shock wave with explosion of the underwater weapon system and to detect small target, the maximum target detection range of the active magnetic sensor needs to be increased. One method for improving maximum target detection range is to improve output power from transmitter through demagnetization factor minimization of a transmitting core. Thus, in this paper, we describe the study results on the transmitter core shape design to enhance output power of the active magnetic sensor.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.428-428
• /
• 2000

A robust intelligent algorithm for AGV navigation control is presented here based on both magnetic and gyro sensors to track a reference trajectory. Since the proposed system uses an intermittent array of short magnetic tape strips, it lends itself to a very easy installation and maintenance compared to other types of positioning references such as electric wire, magnets, RF and laser beacons. The neural network is to predict the lateral deviation of the AGV in the intervals where no magnetic tape references are available. Further, the use of intelligent control ensures a robust and flexible control performance. Computer simulation of AGV control demonstrates its adequate tracking performances even where the sensor information is not available. Real experiments using Samsung AGV are also on the way for real verification

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.608-613
• /
• 2002

In this paper we developed the MPC sensor for steering control and steering control of the AGVDS(Autonomous Guided Vehicle Driving System) for Durability test. Among durability tests, the accelerated durability test has been widely used to evaluate the durability of vehicle structure and chassis parts in a short period of time on the designed road that has severe surface conditions. However it increased the drivers fatigue mainly caused by the severe driving conditions. The driver's difficulty to maintain the constant speed and control the steering wheel reduces the reliability of test results. In addition to the general detecting sensor for steering control was restricted by surrounding condition. So we need to develop steering control sensor was robust in the bad driving condition. In this paper we developed steering control sensor using magnetic induction which is robust in the bad driving condition and implemented the AGVDS.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.2
• /
• pp.140-144
• /
• 2003

A navigation sensor system for outdoor AGV(Automatic Guided Vehicle) using AMR(Anisotropic Magnetoresitive) sensors is described. We derive a formula of the position of AMR sensor using the measured magnetic field intensity due to permanent magnet with constant distance. The system consists of sensor board. sensor control board and position processing board. The sensor board measures magnetic field intensity, the sensor control board controls the measurement of six sensors sequentially, and the position processing board computes the accurate position of the permanent magnet using Least Square Method. We arranged six sensors at intervals of 30cm and measured the position of the permanent magnet moving at intervals of 30cm. Experimental results showed that we can get standard deviation of 2mm and error of &\pm&4.5mm at a height of 20cm from the permanent magnet.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1915-1923
• /
• 2011

For automated guidance control of a magnetically guided-all wheel steered vehicle, it is necessary to have information about position and orientation of the vehicle, and deviations from the reference path in real time. The magnet reference system considered here consists of three magnetic sensors mounted on the vehicle and magnetic markers, which are non-equidistantly buried in the road. This paper presents an observer to estimate such position and orientation at the center of gravity of the vehicle. This algorithm is based on the simple kinematic model of vehicle and uses the data of wheel velocity, steering angle, and the discrete measurements of marker positions. Since this algorithm requires the exact values of initial states, we have also proposed an algorithm of determining the initial position and orientation from the 16 successive magnet pole data, which are given by the magnetic measurement system(MMS). The proposed algorithm is capable of continuing to estimate for the case that the magnetic sensor fail to measure up to three successive magnets. It is shown through experimental data that the proposed algorithm works well within permissible error range.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2008.04a
• /
• pp.205-208
• /
• 2008

This paper propose a advanced technique for exciting and receiving the guided torsional wave to detect flaws in pipe systems. There are some difficulties in selecting and exciting of modes by using the nickel strip attached on pipe systems, such as qualification of residual magnetic field and multi-exciting of the unwanted modes etc. In order to there difficulties we propose the new sensor, so called Crossed-coils sensor. We will prove that it is possible to select the modes to be excited and to find a optimal excitation condition for torsional mode by using the proposed sensor.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.856-862
• /
• 2008

This paper propose a advanced technique for exciting and receiving the guided torsional wave to detect flaws in pipe systems. There are some difficulties in selecting and exciting of modes by using the nickel strip attached on pipe systems, such as qualification of residual magnetic field and multi-exciting of the unwanted modes etc. In order to there difficulties we propose the new sensor, so called Crossed-coils sensor. We will prove that it is possible to select the modes to be excited and to find a optimal excitation condition for torsional mode by using the proposed sensor.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.2
• /
• pp.79-84
• /
• 2021

The most important device of the AGV is the guide sensor, and the typical function of this sensor is high accuracy and extraction of the road. If the accuracy of the guide sensor is low or the sensor device is extracted the wrong track, this causes the problems such as the AGV collision, track-out, the load falling due to AGV swing. In order to improve these problems, this study is proposed a signal processing method of the guide sensor based on multi-maskings and the center of gravity method, and evaluated its performance. As a result, the proposed method showed that the mean error of absolute value is 2.32[mm] and it showed performance improvement of 27[%] than the center of gravity method of existence. Therefore, when the proposed signal processing method is applied, It is thought that the posture control and driving stability of the AGV will be improved.