• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.622-624
• /
• 2008

This investigation studies the effects of material properties and corresponding propagation wave types on optimal configurations of sound absorbing porous materials in maximizing the absorption performance by topology optimization. The acoustic behavior of porous materials is characterized by their material properties which determine motions of the frame and the air. When the frame has a motion, two types of compressional wave propagate in the porous material. Because each wave in the material make different influence on the absorption performance, it is important to understand the relative contribution of each wave to the sound absorption. The relative contribution of the propagating waves in a porous material is determined by the material properties, therefore, an optimal configuration of a porous material to maximize the absorption performance is apparently affected by the material properties. In fact, virtually different optimal configurations were obtained for absorption coefficient maximization when the topology optimization method developed by the authors was applied to porous materials having different material properties. In this investigation, some preliminary results to explain the findings are presented. Although several factors should be considered, the present investigation is focused on the effects of the material properties and corresponding propagation waves on the optimized configurations.

• Journal of Korean Society for Quality Management
• /
• v.45 no.3
• /
• pp.521-532
• /
• 2017

Purpose: The purpose of this study is to structure affective factors related to the tactile sense in order to improve tactile sensibility satisfaction of interior material. In this paper, we propose the design direction of interior material by analyzing the association between material properties and affective factors for automotive interior material. Methods: The relationship between sensibility adjectives and feelings related to tactile sensation were derived through factor analysis after touching prepared samples that were made by changing the material properties of automotive interior material. The association between affective factors and interior material properties were analyzed through ANOVA. Results: Seven kinds of visual and tactile affective factors were derived from the correlation between feeling of material and sensibility adjectives measured by 215 subjects. It is found that there is a quadratic relationship rather than a linear relationship through association analysis between affective factors and the material properties such as roughness, friction coefficient, and hardness. Conclusion: This study suggests the direction of the interior material design which can improve the sensibility satisfaction of the automobile customers by identifying the tactile factors related to the material properties of automotive interior material.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.3
• /
• pp.1-10
• /
• 2022

In this paper, the spatial randomness and probability characteristics of material properties are inversely estimated by using a set of the stochastic fields for the material properties of geotechnical structures. By using the probability distribution and probability characteristics of these estimated material properties, topology optimization is performed on structure shape, and the results are compared with the existing deterministic topology optimization results. A set of stochastic fields for material properties is generated, and the spatial randomness of material properties in each field is simulated. The probability distribution and probability characteristics of actual material properties are estimated using the partial values of material properties in each stochastic field. The probability characteristics of the estimated actual material properties are compared with those of the stochastic field set. Also, response variability of the ground structure having a modulus of elasticity with randomness is compared with response variability of the ground structure having a modulus of elasticity without randomness. Therefore, the quantified stochastic topology optimization result can be obtained with considering the spatial randomness of actual material properties.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.6
• /
• pp.962-971
• /
• 2004

This paper has dealt with thermo-physical properties of microencapsulated phase change material slurry as a latent heat storage material having a low melting point. The measured results of the thermo-physical properties of the test microencapsulated phase change material slurry, those are, density, specific heat, thermal conductivity and viscosity, were discussed for the temperature region of solid and liquid phases of the dispersion material (paraffin). The measurements of these properties of microencapsulated phase change material slurry have been carried out by using a specific-gravity meter, a water calorimeter, a differential scanning calorimeter(DSC), a transient hot wire method and rotating type viscometer, respectively. It was clarified that the additional properties law could be applied to the estimation of the density and specific heat of microencapsulated phase change material slurry and also the Euckens equation could be applied to the estimation of the thermal conductivity of this slurry.

• Structural Engineering and Mechanics
• /
• v.22 no.5
• /
• pp.631-645
• /
• 2006

Buckling capacity of compression members may change due to inadvertent changes in the member section dimensions or material properties. This may be the result of repair, modification of section properties or degradation of the material properties. In some occasions, enhancement of buckling capacity of compression members may be achieved through splicing of plates or utilization of composite materials. It is very important for a designer to predict the buckling resistance of the compression member and the important parameters that affect its buckling strength once changes in section and/or material properties took place. This paper presents an analytical approach for determining the buckling capacity of a compression member whose geometric and/or material properties has been altered resulting in a multi-step non-uniform section. This analytical solution accommodates the changes and modifications to the material and/or section properties of the compression member due to the factors mentioned. The analytical solution provides adequate information and a methodology that is useful during the design stage as well as the repair stage of compression members. Three case studies are presented to show that the proposed analytical solution is an efficient method for predicting the buckling strength of compression members that their section and/or material properties have been altered due to splicing, coping, notching, ducting and corrosion.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.29-34
• /
• 1993

Although bonding material content of the high strength flowing concrete is very important in engineering properties, in rich mix concrete increasing the bonding material content may not follow more good properties. This study is to investigate the influence of the bonding material content affecting on the engineering properties of high strength flowing concrete, and this paper is to analyze the properties of fresh concrete. The results reveal that concrete of less bonding material content has about the same good consistency as concrete of more bonding material content, and that the evaluation methods of workability have to change in high strength flowing concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1993.10a
• /
• pp.35-38
• /
• 1993

Although bonding material content of the high strength flowing concrete is very important in engineering properties, in rich mix concrete increasing the bonding material content may not follow more good properties. This study is to investigate the influence of the bonding material content affecting on the engineering properties of high strength flowing concrete, and this paper is to analyze the properties of hardened concrete. The results reveal that the strength of concrete having loss bonding material content is higher than that of concrete having more bonding material content, and that in proportion to increasing of concrete strength brittleness factors decrease, and that the static modulus of elasticity in this study is less than that in specification.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.23-26
• /
• 2002

In ceramic systems using LTCC, many components including embedded passives and TRL's are used for composition of 3-dimensional circuit. So the exact analysis on this components must be performed. As for the TRL's, material properties including electrical conductivity of metal, loss factor and effective dielectric constant of dielectric material and geometrical factors like roughness of surface, vias, dimension of TRL structure have a large effect on the characteristics of transmission lines. Such properties of materials have different values in each system with ideal ones presented in text book. In this research, the effective material properties in each system are examined and the effect of material properties and geometrical factors on the characteristics of TRL's are analyzed and quantified by simulation and measurement.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.701-709
• /
• 2002

Aluminium foam material is highly porous material, which has the complicated cellular structure defined by randomly distributed pores in metallic matrix. This structure gives the characteristic properties which cannot be achieved by any other conventional processes. As the properties of aluminium foam material significantly depend on its porosity, a desired profile of properties can be tailored by changing the foam density. But various defects lead to undesirable effects on the mechanical properties. Mechanical properties are dependent on cell sizes and aspect ratios. Therefore, this paper presents the effects of various processing parameters of various parameters on the mechanical properties. For the sake of this, combined stirring was used to fabricate aluminum foam materials by the parameters. Compression and bending tests were performed to investigate the effects of cell sizes and aspect ratios on the mechanical properties.

• Composites Research
• /
• v.23 no.3
• /
• pp.37-42
• /
• 2010

The fiber material properties, elastic constant and strength, are the most important factors among the various material properties for the design of composite pressure vessel, because of it's dominant influence on the performance of composite pressure vessel. That is, the deformation and burst pressure of pressure vessel highly affected by the fiber material properties. Therefore, the establishment of test method for exact fiber material properties is a priority item to design a composite pressure vessel. However, the fiber material properties in filament wound pressure vessel is very sensitive on various processing variables (equipment, operator and environmental condition etc..) and size effect, so that it isn't possible to measure exact fiber material properties from existing test methods. The hydro-burst test with full scale pressure vessel is a best method to obtain fiber material properties, but it requires a enormous cost. Thus, this paper suggests a newly developed test method, hoop ring test, that is capable of pressure testing with ring specimens extracted from real composite pressure vessel. The fiber material properties from hoop ring test method showed good agreement with the results of hydro-burst test with full scale composite pressure vessels.