• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.767-772
• /
• 2018

Among various mechanisms for ER phenomena, the electrostatic polarization and conduction models were known as the most promising theoretical models. However, many inherited defects have limited their uses for the development of effective ER fluids. To resolve these problems, extended Maxwell-Wagner polarization model with Onsager theory was developed. It was observed that the extended model resolved the problems, suggesting that the extended model can be used for the development of effect ER fluids.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.480-485
• /
• 2020

The extended Maxwell-Wagner polarization model is employed to describe the ER behavior of the conducting particle ER suspensions, and solutions to the equation of motion are obtained by dynamic simulation. The simulation results show the nonlinear ER behavior (Δτ∝Eⁿ, n≈1.5) of the conducting particle ER suspensions. The response point, where shear stress reaches steady-state, is the point where stable break-up and rebuild of the chain-like structure of particles reaches. Also, it shows the minimum of shear stress, which corresponds the start-up of random particle configuration. The shear stress reaches plateau as particle volume fraction increases.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.3
• /
• pp.139-142
• /
• 2007

Organic field-effect transistor (FET) based on a copper Phthalocyanine (CuPc) material as an active layer and a $SiO_2$ as a gate insulator were fabricated and analyzed. We measured the typical FET characteristics of CuPc in air. The electrical characteristics of the CuPc FET device were analyzed by a Maxwell-Wagner model. The Maxwell-Wagner model employed in analyzing double-layer dielectric system was helpful to explain the C-V and I-V characteristics of the FET device. In order to further clarity the channel formation of the CuPc FET, optical second harmonic generation (SHG) measurement was also employed. Interestingly, SHG modulation was not observed for the CuPc FET. This result indicates that the accumulation of charge from bulk CuPc makes a significant contribution.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.613-619
• /
• 2022

The extended Maxwell-Wagner polarization model is employed to describe the ER(Electrorheological) behavior of bi-dispersed ER suspensions, and solutions to the equation of motion are obtained by dynamic simulation. Under the same particle volume fraction, it is found that the dynamic yield stresses of uniform size suspensions do not depend on the particle size. Compared with uniform size suspensions, the dynamic yield stress is reduced for ER fluids consisting of two kinds of particles with different sizes. Compared with the dynamic yield stress behavior, for ${\dot{\gamma}}^*$≧0.01 the shear stress shows different behaviors depending on the particle sizes and the raio of different size particles. The simulation results show the nonlinear ER behavior (∆_𝛕 ∝ Eⁿ, n ≈ 1.55) of the conducting particle ER suspensions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.70-71
• /
• 2007

Analyzing pentacene field effect transistors (FETs) with Au source and drain electrodes as Maxwell-Wagner effect elements, electron and hole injection from the Au electrodes into the FET channel were examined using current-voltage (I-V), capacitance-voltage (C-V) and optical second harmonic generation (SHG) measurements. Based on these results, a mechanism of the hole and electron injection into pentacene from the Au electrodes and subsequently recombination mechanism with light-emitting in the pentacene layer are discussed, with taking into account the presence of trapped charges.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.515-521
• /
• 2013

Magnetoelectric(ME) bulk composites with PZT-PNN-PZN/$Fe_2O_4$ were prepared by using a conventional ceramic methods and investigated on the ME voltage vs frequency of ac magnetic fields. We made the electric equivalent circuits by using the Maxwell-Wagner model and simulated the frequency dependence of ME voltage in low frequency region. ME devices were described by a series of two equivalent circuits of piezoelectric and magnetic, which have the relaxation time ${\tau}$ due to the interaction between ME device and load resistor. Equivalent circuit of piezoelectric material is independent of frequency. However ferrite magnetic materials have Debye absorption and dipolar dispersion, whose equivalent circuit is a function of frequency. Therefore we suggest the resistance in the equivalent circuit is proportion to $1+{\omega}^2{\tau}^2$ and the capacitance is in inverse proportion to $1+{\omega}^2{\tau}^2$ in the magnetic materials.

• Electrical & Electronic Materials
• /
• v.11 no.10
• /
• pp.24-31
• /
• 1998

Interfacial effect in polymetric composites have been studied extensively. This report deals mainly with the effects of interfacial space charge and interface structure. A model for the dynamic process of interfacial space charge accumulation is proposed. The new model might interpret some interface phenomena which is difficult to be explained in terms of traditional Maxwell-Wagner theory. An interface structure is also presented, by which the importance of surface treatment of glass Fiber for improving the properties of FRP could be well understood.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.73-76
• /
• 2007

Electro-Active paper (EAPap) is a new smart material that has a potential to be used in biomimetic actuator and sensor. It is made by cellulose that is abundant material in nature. EAPap is fascinating with its biodegradability, lightweight, large displacement, high mechanical strength and low actuation voltage. Actuating mechanism of EAPap is known to be the combined effects of ion migration and piezoelectricity. However, the electromechanical actuation mechanisms are not yet to be established. This paper presents the modeling of the actuation behavior of water infused cellulose samples and their composite dielectric constants calculated by Maxwell-Wagner theory. Electro-mechanical forces were calculated using Maxwell stress tensor method. Bending deflection was evaluated from simple beam model and compared with experimental observation, which result good correlation with each other.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1179-1183
• /
• 2007

Electro-Active paper(EAPap) is a new smart material that has a potential to be used in biomimetic actuator and sensor. It is made by cellulose that is abundant material in nature. EAPap is fascinating with its biodegradability, lightweight, large displacement, high mechanical strength and low actuation voltage. Actuating mechanism of EAPap is known to be the combined effects of ion migration and piezoelectricity. However, the electromechanical actuation mechanisms are not yet to be established. This paper presents the modeling of the actuation behavior of water infused cellulose samples and their composite dielectric constants calculated by Maxwell-Wagner theory. Electro-mechanical forces were calculated using Maxwell stress tensor method. Bending deflection was evaluated from simple beam model and compared with experimental observation, and which result in good correlation with each other.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.4
• /
• pp.151-155
• /
• 2008

Using pentacene field effect transistors (FETs) with Au source and drain electrodes, electron injection from the Au electrodes into the pentacene was investigated. The capacitance-voltage (C-V) and optical second harmonic generation (SHG) measurements were employed. Electron injection from the Au electrodes was suggested by the hysteresis behavior with the C-V characteristics and slowly decaying SHG signal under DC biasing, A mechanism of hole-injection assisted by trapped electrons is proposed. To confirm electron injection process, light-emitting behavior under the application of AC applied voltage was observed.