• Journal of Korea Foundry Society
• /
• v.17 no.3
• /
• pp.237-244
• /
• 1997

This study has been carried out to investigate into the influence of solidification conditions mold on the structure and mechanical properties of Al-5wt%Mg alloy by metallic mold casting. The percentage of equiaxed grain of Al-5wt%Mg alloy castings increased both when pouring temperature decreased and when the low part or bottom of metallic mold was cooled. The hardness was checked and showed that hardness of outside in the castings was higher than that inside, and that it is the highest at the pouring temperature of $680^{\circ}C$. The castings had the highest U.T.S. and elongation when the bottom of metallic mold was cooled. At the same pouring temperature, the structure of castings was changed as the position of cooling parts of metallic mold was varied. When the castings were solidified through cooling of the bottom of the metallic mold, the morphology of Fe intermetallic compound has tendency to change to a Chinese script and the U.T.S. and elongation of Al-5wt.%Mg alloy castings was increased.

• Journal of Korea Foundry Society
• /
• v.13 no.2
• /
• pp.155-162
• /
• 1993

This study has been focused on the influence of the metallic mold cooling effects on the solidification structures and the mechanical properties for Al-10%Si alloy castings by the variation of pouring temperatures, metallic mold temperatures and Cooling part of metallic mold. The dendrite arm spacing of Al-10%Si alloy was decreased with increasing cooling rate. In case of bottom cooling of metallic mold, DAS was appeared to be $20-22{\mu}m$ and in the middle cooling, it was increased to $36-40{\mu}m$. The DAS decreased proportionally $with(cooling\;rate)^{-3/2}$ at pouring temperatures $680^{\circ}C$ and $(cooling\;rate)^{-1/2}$ at pouring temperature $760^{\circ}C$, but it was proportionally increased to $(local\;solidification\;time)^{1/2-1/3}$ at pouring temperature $680^{\circ}C$ and $760^{\circ}C$. The maximum tensile strength of Al-10%Si alloy casting was obtained in case of bottom cooling of mold at pouring temperature $680^{\circ}C$ and metallic mold temperature $320^{\circ}C$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.142-151
• /
• 2013

This study develops an automation system for metallic mold design that is applicable in forging non-axial symmetric parts. The metallic mold design program is used to design the metallic mold using two-dimensional axial symmetric metallic molds and to predict the stress concentration using finite element analyses. Then, the program redesigns the metallic mold using variables such as the optimal split diameter, maximum allowable inner pressure, fit tolerance, and stress distribution, which are calculated using the metallic mold design program. When the involute spur gear is forged, stress concentration occurs on the tooth root bounded at the symmetric surface. The SCM4 material is suitable for metallic molds because the stress is less than the yield strength of the insert and it acts on the tooth root regardless of the inner pressure. The metallic mold for forging non-axial symmetric parts can be designed through adjusting the magnitude of the contact pressure. The program developed in this study can be applied to metallic mold designs in involute spur gears of forging, which is an ordinary non-axial symmetric part.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.9
• /
• pp.1470-1479
• /
• 1997

In this study, the plastic fan with high efficiency and low noise was designed and the capacity of the wind and the wind pressure were analysed and verified by CAE. After designing the metallic mold using the metallic mold design data, and the the metallic mold design was reformed by analysing the process of the material stream and injection filling by CAE. Also the metallic mold cutting data were formed using the metallic mold design data. These cutting data was used to produce the fan electrode by a machining center and then this electrode were used to manufacture the metallic mold by cutting the fan cavity by an electrical spark machine. The purpose of this study is to find out the sub-optimal condition on the productivity and improvement in quality of the plastic fan by integrating a series of this process with a computer.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.450-461
• /
• 1993

AC4C alloy casts in the metallic mold, zircon sand mold, silica sand mold and shell mold with the pouring temperatures of 680, 710 and $740^{\circ}C$ have been investigated. The tensile strength, elongation and hardness of AC4C alloy castings have been influenced by the kind of molds used. The mechanical properties in zircon sand mold castings were greater than those in other sand mold castings, but were inferior to the properties in metallic mold castings. Eutectic Si particle size and DAS were increased in the order of metallic mold, ziron sand mold, silica sand mold and shell mold. Also, they were increased with the increase of pouring temperatures. DAS, eutectic Si particle size and grain size decreased with the increase of mechanical properties as the cooling rate increased. The eutectic Si particle size and DAS of AC4C alloy castings after T6 treatment were decreased in as-cast. The variation of eutectic Si particle size has been effected on the tensile strength, elongation and fractured surface.

• Korean Journal of Materials Research
• /
• v.31 no.6
• /
• pp.331-338
• /
• 2021

Ti-Al-Si target and Cr-Si target are sputtered alternately to develop a multi-layered nitride coating on a steel mold to improve die-casting lifetime. Prior to the multi-layer deposition, a CrN layer is developed as a buffer layer on the mold to suppress the diffusion of reactive elements and enhance the cohesive strength of the multi-layer deposition. Approximately 50 nm CrSiN and TiAlSiN layers are deposited layer by layer, and form about three ㎛-thickness of multi-layered coating. From the observation of the uncoated and coated steel molds after the acceleration experiment of liquid metal injection casting, the uncoated mold is severely eroded by the adhesion of molten metallic glass. On the other hand, the multi-layer coating on the mold prevents element diffusion from the metallic glass and mold erosion during the experiment. The multi-layer structure of the coating transforms the nano-composite structured coating during the acceleration test. Since the nano-composite structure disrupts element diffusion to molten metallic glass, despite microstructure changes, the coating is not eroded by the 1,050 ℃ molten metallic glass.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2541-2543
• /
• 1998

This paper describes the fabrication process to fabricate metallic structure of high aspect ratio using LlGA-like process. SU-8 is used as an electroplating mold. SU-8 is an epoxy-based photoresist, designed for ultrathick PR structure with single layer coating [1,2]. We can get more than $100{\mu}m$ thick layer by single coating with conventional spin coater, and applying multiple coating can make thicker layers. In the experiments, we used different kinds of SU-8, having different viscosity. To optimize the conditions for mold fabrication process, experiments are performed varying spinning time and speed, soft-bake, develop and PEB (Post Expose Bake) condition. With the optimized condition, minimum line and space of $3{\mu}m$ pattern with a thickness of $40{\mu}m$ and $4{\mu}m$ pattern with a thickness of $130{\mu}m$ were obtained. Using the patterned PR as a plating mold, metallic structure was fabricated by electroplating. We have fabricated a electroplated nickel comb actuator using SU-8 as plating mold. The thickness of PR mold is $45{\mu}m$ and that of plated nickel is$40{\mu}m$. Minimum line of the mold is $5{\mu}m$. Patterned metallic layer or polymer layer, which has selectivity with the structural plated metallic layer, can be used as sacrificial layer for fabrication of free-standing structure.

• Journal of Sensor Science and Technology
• /
• v.32 no.4
• /
• pp.252-256
• /
• 2023

A one-step method for nanoscale patterning of silver ionic ink on a substrate is developed using a microscale, elastic mold deformation. This method yields unique micro/nanoscale metallic structures that differ from those produced using the original molds. The linewidth of these metallic structures is significantly reduced (approximately 10 times) through the sidewall deformation of the original mold cavity on a thin liquid film, as verified by finite element analysis. The process facilitates the fabrication of various, isolated and complex micro/nanoscale metallic structures with negligible residual layers at low cost and high throughput. These structures can be utilized for various applications, including optoelectronics, wearable sensors, and metaverse-related devices. Our approach offers a promising tool for manipulation and fabrication of micro/nanoscale structures of various functional materials.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.437-438
• /
• 2012

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.8 no.2
• /
• pp.94-99
• /
• 2008

The replica of silicone mold which can produce the test samples and the market-displayable products without making expensive metallic patterns is advantageous because it incurs less cost than the ordinary method that manufactures the products from the metallic patterns. However, the production of the products using silicone mold should require a technician with professional knowledge about the metallic patterns every time. Thus we tried to judge whether a forming analysis software for iron molding can be applied to silicon molding in this paper. In other words, this paper suggests a method to use a computer simulator from the designing step of the silicone mold, which is the most important part in making replica using simple silicone molds to the step of pouring the cast. The paper shows that if the know-how of a professional worker is provided in advance, an amateur worker can easily produce silicone molds of the best quality, the defective rate of the products will be decreased, and the replica will have a more complete status. By doing so, we suggested a possibility for reducing the delivery time at the production sites and for improving the product quality.