• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.817-822
• /
• 2011

We propose a novel ring structure based on the stadium-shaped ring resonator (SSRR) with dual photonic crystal microcavity (DPCM) for biosensor and analyzed the sensing characteristics. The Q-factor of the photonic crystal microcavity (PCM) can be significantly enhanced when the PCM or DPCM has the same resonance condition as the SSRR. The simulation results show that the Q-factor of the SRR with DPCM was increased by three times in comparison with single PCM structure. We also defined a mutual interference between two PCMs. Assuming a detectable spectral resolution of 10 picometers, a refractive index resolution of $3.03\times10-5$ can be measured on the SSRR-DPCM.

• Current Optics and Photonics
• /
• v.5 no.6
• /
• pp.730-737
• /
• 2021

Transmission spectra are measured from waveguide-coupled ring resonators fabricated with SiN_x on SiO₂. By using ring resonators with various radii and several index contrasts, the behavior of the quality factors is investigated. As the index contrast decreases, the dominant loss is from scattering for a large resonator, while that changes from scattering loss to bending loss for a small resonator. We verify that the quality factor can be drastically improved by reducing the index contrast in large ring resonators.

• Journal of Navigation and Port Research
• /
• v.28 no.4
• /
• pp.293-297
• /
• 2004

In this papers, an S-band oscillator of the low phase noise property using a miniaturized micro-strip hairpin shaped ring resonator is presented The substrate has a dielectric constant $\epsilon_\gamma$＝3.5, a thickness h＝0.508 mm, and loss tangent $tan\delta$＝0.002. A designed and fabricated oscillator shows low phase noise performance of 99. 71 dBc/Hz at 100 KHz offset frequency and of output power 19.584 dBm at center frequency 2.450 GHz. This circuit was fabricated with hybrid technique, but can be fully compatible with the MMIC due to its entirely planar structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.1014-1020
• /
• 2009

In this paper, a novel UWB(Ultra Wide-band) antenna with suppressed band of IEEE 802.11a($5.15{\sim}5.825\;GHz$) WLAN was designed and fabricated by using SRR(Split Ring Resonator) with band rejection property. MWS(Micro-wave Studio) of CST company was utilized in the design stage. The antenna was fabricated on a substrate, Rogers 4003, with the thickness of 0.8 mm and relative permittivity of 3.38. The measured result shows that the proposed antenna has a good return loss below -10 dB and group delay below 1nsec over UWB communication band($3.1{\sim}10.6\;GHz$) except WLAN band. It also shows the omni-directional radiation pattern.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.46-54
• /
• 2007

We have fabricated and characterized MMI (Multimode Interference) coupled ring resonator with the total internal reflection mirrors and the semiconductor optical amplifier for the integration of the WDM (Wavelength Division Multiplexing) system. The TIR (Total Internal Reflection) mirrors were fabricated by self-aligned process and had losses of about 0.71 dB per mirror. Coupling in and out of a resonator was achieved using the extremely small MMI couplers. The MMI length and width used in the experiment were $119{\mu}m$ and $9{\mu}m$, respectively. The resulting FSR (Free Spectral Range) and on-off ratio were approximately 1.333 nm (162 GHz) and 13 dB, respectively.

• Korean Journal of Optics and Photonics
• /
• v.18 no.3
• /
• pp.216-220
• /
• 2007

A widely tunable add/drop filter composed of double ring resonators is implemented with high-index-contrast polymer waveguide. To enhance the productivity, directional couplers are designed to have good fabrication tolerance. The refractive indices of the core and cladding in the 1550 nm wavelength are 1.51 and 1.378, respectively. Drop response in comparison with neighborhood peak gets enhanced by more than 2.9 dB at the wavelength where both rings resonate. This filter can be used to build widely tunable laser diode through hybrid-integration with reflective SOA.

• Current Optics and Photonics
• /
• v.2 no.6
• /
• pp.576-581
• /
• 2018

A new approach for identification of a microwave frequency using an integrated optical waveguide chip, combined with a phase modulator (PM) and two microring resonators (MRRs), is proposed, theoretically deduced, and verified. By wavelength tuning to set the PM under the condition of a double side band (DSB), the measurement range can be started from the dc component, and the measurement range and response slope can be adjusted by designing the radius and transmission coefficient of the MRR. Simulations reveal that the amplitude comparison function (ACF) has a monotonic relationship from dc to 32.5 GHz, with a response slope of 5.15 dB under conditions of DSB modulation, when the radius values, transmission coefficients, and the loss factors are designed respectively as $R_1=400{\mu}m$, $R_2=600{\mu}m$, $t_1=t_2=0.63$, and ${\gamma}_1={\gamma}_2=0.66$. Theoretical calculations and simulation results both indicate that this new approach has the potential to be used for measuring microwave frequencies, with the advantages of compact structure and superior reconfigurability.