• 대한교통학회지
• /
• 제34권6호
• /
• pp.499-509
• /
• 2016

보행교통류의 통행은 다른 교통수단과 비교하여 더 미시적인 움직임을 보인다. 정해진 차선의 구분 없이 통행하므로 2차원적인 움직임을 보일 수 있으며, 자유로운 방향전환 능력을 통해 이동할 수 있다. 이러한 이유로 보행교통류의 편의성을 평가하는 방법에 있어서도 보행교통류의 미시적인 특성이 반영되어야 한다고 할 수 있다. 만일 보행자만의 행태를 반영하여 편의성을 평가할 수 있다면 보행교통류의 통행 특성을 더 원활히 파악할 수 있을 것이다. 이에 본 연구에서는 보행교통류의 특성을 반영하여 편의성을 판단할 수 있는 지표들을 시뮬레이션을 통해 제시하였다. 본 연구에서는 경로이탈도, 속도의 변화 크기, 그리고 충돌 횟수라는 세 편의성 지표를 통해 보행교통류의 편의성을 평가할 수 있음을 보였다. 각각의 지표들은 보행교통류의 고유한 통행 특성을 해석할 수 있으면서도, 교통류율의 변화에 따라 서로 다른 함수 형태를 보였다. 결과적으로 기존의 교통유율이나 속도와 더불어서 LOS를 판단할 수 있는 보조 지표로 활용될 수 있음을 알 수 있었다.

• 대한교통학회지
• /
• 제19권5호
• /
• pp.7-18
• /
• 2001

본 연구는 도시물류 문제를 미시적 및 거시적 관점으로 정의하고, 국내외 문헌의 현황 및 한계점을 밝히고, 향후 연구방향을 제시하며, 정책 대안을 평가하는 모형을 개념적으로 제시하는 것을 목적으로 하였다. 문헌의 한계점을 바탕으로 하여 추후 연구 방향으로서는 도시내 물류활동 주체인 화주, 제품공급업자 등을 고려하는 미시적 관점의 연구가 강화되어야 한다는 점과 다양한 정책 대안들을 보다 효과적으로 평가할 수 있는 개념적 평가 모형 정립의 필요성 그리고 물류활동 주체와 도시 교통 문제를 함께 평가할 수 있는 통합 모형의 구축을 제의하였다. 도시물류 개선 대안을 평가하기 위한 모형을 개념적으로 제시하는 데 있어서 거시적 관점과 미시적 관점의 상관관계를 정리하고, 미시적 관점에서 관련 주체별 평가 요소를 도출하고 이를 바탕으로 평가 모형을 구체화하였다. 특히, 최근 시도된 시뮬레이션 기법을 이용한 화물차량경로 예측 방법을 제시하고, 모형을 통하여 도시물류 개선을 위한 정책 대안이 각 물류활동의 주체에게 미치는 영향을 미시적 및 거시적 관점에서 평가할 수 있음을 밝혔다. 또한 향후 본 연구에서 제시된 모형들을 보다 구체화하는 노력이 필요할 뿐 아니라 재고관리 시스템을 통한 수요예측 기법 등의 기초 연구가 계속되어야 함을 강조하였다.

• Geomechanics and Engineering
• /
• 제34권5호
• /
• pp.577-595
• /
• 2023

A dynamic triaxial discrete element numerical model of lightweight soil was established using the discrete element method to study the microscopic mechanism of expanded polystyrene (EPS) particles in the soil under cyclic loading. The microscopic parameters of the discrete element model of the lightweight soil were calibrated depending on the dynamic triaxial test hysteresis curves. Based on the calibration results, the effects of the EPS particles volume ratio and amplitude on the contact force, displacement field, and velocity field of the lightweight soil under different accumulated strains were studied. The results showed that the hysteresis curves of lightweight soil exhibit nonlinearity, hysteresis, and strain accumulation. The strain accumulated in remolded soil is mainly tensile strain, and that in lightweight soil is mainly compressive strain. As the volume ratio of EPS particles increased, the contact force first increased and then decreased, and the displacement and velocity of the particles increased accordingly. With an increase in amplitude, the dynamic stress of the particle system increased, and the accumulation rate of the dynamic strain of the samples also increased. At 5% compressive strain, the contact force of the particles changed significantly and the number of particles deflected in the direction of velocity also increased considerably. These results indicated that the cemented structure of the lightweight soil began to fail at a compressive strain of 5%. Thus, a compressive strain of 5% is more reasonable than the dynamic strength failure standard of lightweight soil.

• 대한기계학회논문집B
• /
• 제34권6호
• /
• pp.569-577
• /
• 2010

다상 유체 시스템에 적용할 수 있는 다중스케일 입자 시뮬레이션 기법을 개발하였다. 거시 모델과 미시모델이 만나는 경계영역에서 세가지로 구별되는 기능을 수행하도록 하였다. 먼저, 기상과 액상을 분리하여 연결하기 위해 벽을 설정하였다. 또 경계영역을 근처에서 경계의 위치를 측정하고 이것에 벽의 각도와 위치가 연동하여 접촉각 값을 미시모델에서 거시모델로 전달하게 하였다. 마지막으로, 입자의 삽입과 제거를 통해 경계영역의 질량과 온도를 거시적 조건에 맞추도록 하였다. 이 알고리즘들을 적용한 완전습윤과 부분습윤시스템들은 좋은 결합 결과를 보였다.

• 소성∙가공
• /
• 제12권1호
• /
• pp.60-65
• /
• 2003

HIP diffusion bonding of Ni-based superalloys, cast Mar-M247 (MM247) and Udimet 720 (U720) powder, was experimentally and numerically studied. Subsolvus HIP treatment was optimized by investigating the variations of high temperature tensile properties of HIP-bonded specimens with powder size, HIP'ing time, etc. While the tensile strength at high temperatures showed no detectable changes, the tensile elongation and reduction in area were slightly increased as the powder size decreased from -140 mesh to -270 mesh. While as-HIP'ed U720 showed a high tensile strength comparable to that of lorded U720 alloy, the HIP diffusion-bonded specimen showed a strength lower than the forged U720 alloy and the cast MM247 alloy The increase of HIP'ing tune from 2 hours to 3 hours resulted in a rapid risc of tensile strength and elongation due to the disappearence of microvoids in the cast MM247. FEM simulation for HIP process was conducted by applying the McMeeking micromechanical model, which uses power-law creep model as constitutive equations. ABAQUS user subroutine CREEP with an implemented microscopic model was used for the simulation. Numerical simulation was shown to be essential for the near-net shape manufacturing as well as the HIP process optimization.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.340-340
• /
• 2016

We have prepared alumina (Al2O3) doped zinc oxide (AZO) films by DC magnetron sputtering (MS) technique and obtained higher self surface texturing at a high target angle (f). We have characterized the films and applied it as a front electrode of a single junction amorphous silicon solar cell. At a lower f the deposited films show higher values of optical gap (Eg), charge carriers mobility & concentration, crystallite grain size and wider wavelength range of transmission. At higher target angle the sheet resistance, surface roughness, haze factor etc for the films increase. For f=72.5o the haze factor for diffused transmission becomes 6.46% at 540 nm wavelength. At f=72.5o the material shows a reduction in crystallinity and evolution of a hemispherical-type sub-micron surface textures. A Monte Carlo method (MCM) of simulation of the AZO film deposition shows that such an enhanced self-surface texturing of the films at higher f is possible.

• 한국환경과학회지
• /
• 제25권12호
• /
• pp.1597-1611
• /
• 2016

A numerical assessment using mesoscale-CFD (computational fluid dynamics) coupled A2C (atmosphere to CFD) model was carried out to analyze the variation of microscopic air flow pattern due to the construction of the Chilgok barrage in the Nakdong River. Scenarios with air flow patterns were classified into pre- and post-construction. The increased width of the river due to the construction of the Chilgok barrage induced obvious changes in moisture and the thermal environment around the river. However, air temperature variation was restricted within an area along the windward side in the numerical assessment. The impact of barrage construction on air temperature tends to be stronger during the nighttime than the daytime. It also stronger during the winter than the summer. In the simulation, the convergence of mesoscale wind is more pronounced after barrage construction than before. This is caused by the change of heat flux pattern induced by the widening of the river. Although this work is a case study with restricted atmospheric stability conditions that has several limitations in the numerical simulations, the impacts of the land-use changes brought about by the construction of the barrage in the river acceptable.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.67-70
• /
• 2004

An investigation was performed to study the impact damage of the laminated composite plates caused by a low- velocity foreign object with multi-scale modeling based on the concepts of Direct Numerical Simulation (DNS)[4]. In the micro-scale part, we discretize the composite plates through separate modeling of fiber and matrix for the local microscopic analysis. A micro-scalemodel was developed for predicting the initiation of the damage and the extent of the final damage as a function of material properties, laminate configuration and the impactor's mass, etc. Anda macro-scale model was developed for description of global dynamic behavior. The connection betweenmicroscopic and macroscopic is implemented by the tied interface constraints of LS-DYNA contact card. A transient dynamic finite element analysis was adopted for calculating the contact force history and the stresses and strains inside the composites during impact resulting from a point-nose impactor. The low-velocity impact events such as contact force, deformation, etc. are simulated in the macroscopic sense and the impact damages, fiber-breakage, matrix cracking and delamination etc. are examined in the microscopic sense.

• Structural Engineering and Mechanics
• /
• 제74권3호
• /
• pp.407-423
• /
• 2020

The pre-peak cyclic shear mechanism of two-order asperity degradation of rock joints in the direct shear tests with static constant normal loads (CNL) are investigated using experimental and numerical methods. The laboratory testing rock specimens contains the idealized and regular two-order triangular-shaped asperities, which represent the specific geometrical conditions of natural and irregular waviness and unevenness of rock joint surfaces, in the pre-peak cyclic shear tests. Three different shear failure patterns of two-order triangular-shaped rock joints can be found in the experiments at constant horizontal shear velocity and various static constant normal loads in the direct and pre-peak cyclic shear tests. The discrete element method is adopted to simulate the pre-peak shear failure behaviors of rock joints with two-order triangular-shaped asperities. The rock joint interfaces are simulated using a modified smooth joint model, where microscopic scale slip surfaces are applied at contacts between discrete particles in the upper and lower rock blocks. Comparing the discrete numerical results with the experimental results, the microscopic bond particle model parameters are calibrated. Effects of cyclic shear loading amplitude, static constant normal loads and initial waviness asperity angles on the pre-peak cyclic shear failure behaviors of triangular-shaped rock joints are also numerically investigated.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1388-1392
• /
• 2018

Metal thin films are used widely to solve the vibration problem. However, damping mechanism is still not clear, which limits the further improvement of the damping properties for film and the development of multi-functional damping coating. In this paper, Damping microscopic mechanism of porous metal films was investigated at both macroscopically and microscopically mixed levels. Molecular dynamics simulation method was used to model and simulate the loading-unloading numerical experiment on the micro-pore and vacancy model to get the stress-strain curve and the microstructure diagram of different defects. And damping factor was calculated by the stress-strain curve. The results show that dislocations and new vacancies appear in the micro-pores when metal film is stretched. The energetic consumption from the motion of dislocation is the main reason for the damping properties of materials. Micro-mechanism of damping properties is discussed with the results of in-situ experiment.