• Computers and Concrete
• /
• 제23권1호
• /
• pp.37-47
• /
• 2019

In view of the increasing utility of concrete as a construction material, the major challenge is to improve the quality of construction. Nowadays the common problem faced by many of the concrete plants is the shortage of river sand as fine aggregate material. This led to the utilization of locally available materials from quarries as fine aggregate. With the percentage of fines present in Crushed Rock Fines (CRF)or crushed sand is more compared to river sand, it shows a better performance in terms of fresh properties. The present study deals with the formulation of SCC mix design based on the chosen plastic viscosity of the mix and the measured plastic viscosity of cement pastes incorporating supplementary cementitious materials with CRF and river sand as a fine aggregate. Four different combinations including two binary and one ternary mix are adopted for the current study. Influence of plastic viscosity of the mix on the fresh and hardened properties are investigated for SCC mixes with varying water to cement ratios. It is observed that for an increasing plastic viscosity of the mix, slump flow, T500 and J-ring spread increased but V-funnel and L-box decreased. Compressive, split tensile and flexural strengths decreased with the increase in plastic viscosity.

• Computers and Concrete
• /
• 제20권4호
• /
• pp.461-468
• /
• 2017

With the increasing demand in the production of concrete, there is a need for adopting a feasible, economical and sustainable technique to fulfill practical requirements. Self-Compacting Concrete (SCC) is one such technique which addresses the concrete industry in providing eco-friendly and cost effective concrete. The objective of the present study is to develop a mix design for SCC with Crushed Rock Fines (CRF) as fine aggregate based on the plastic viscosity of the mix and validate the same for its fresh and hardened properties. Effect of plastic viscosity on the fresh and hardened properties of SCC is also addressed in the present study. SCC mixes are made with binary and ternary blends of Fly Ash (FA) and Ground Granulated Blast Slag (GGBS) with varying percentages as a partial replacement to Ordinary Portland Cement (OPC). The proposed mix design is validated successfully with the experimental investigations. The results obtained, indicated that the fresh properties are best achieved for SCC mix with ternary blend followed by binary blend with GGBS, Fly Ash and mix with pure OPC. It is also observed that the replacement of sand with 100% CRF resulted in a workable and cohesive mix.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.457-462
• /
• 1999

The purpose of this study is to design the requirements for the materials of stabilizing slurry and to determine the optimum slruuy mix design used in the underground wall of Inchon LNG #213 and 214 tank. After the materials and mix conditions of stabilizing slurry investigated and tested, we propose materials and optimum mix design according to testing items including funnel viscosity, we propose materials and optimum mix design according to testing items including funnel viscosity, fluid loss, cake thickness and specific gravity. As this results, we select optimum mix design that the upper limit ratio of bentonite is 2.0%, polymer is 0.1% considering the funnel viscosity and dispersion agent is 0.05% considering the fluid loss. Also we select all materials which are composed of GTC4 as bentonite, KSTP as polymer and Bentocryl as dispersion agent. All test results are satisfied our specifications for stabilizing slurry.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.35-36
• /
• 2016

Recently, with the increasing demand of high performance of concrete, the mix design of concrete mixture has became low water-to-binder ratio with high binder content. To compensate these trend of mix design, high range water reducer, or superplascizier has been invented to achieve high flowable concrete. Although this superplasticizer provides favorable workability based on its dispersing action on the components of concrete mixture, it has an limitation of decreasing viscosity of the mixture, and thus it is difficult to secure sufficient workability for high performance concrete mixtures with high binder content. To improve the workability of concrete with high viscosity, recently, low-viscosity type superplasticizer was introduced, and in this research, a fundamental properties of low-viscosity type superplasticizer is evaluated.

• KCI Concrete Journal
• /
• 제14권4호
• /
• pp.151-159
• /
• 2002

This study investigates experimentally the optimum mix proportion and design factors of the stabilizing liquid used for excavation of the massive and deep slurry wall in LNG in-ground tank before pouring concrete. Considering those site conditions, the stabilizing liquid used for excavation of slurry wall has to be satisfied with some requirements including specific gravity, fluid loss, cake thickness, funnel viscosity and sand content in order to construct the safe and qualified slurry wall. For this purpose, we select materials including bentonite, polymer and dispersion agent. After performing many tests for materials and mix design process, we propose the optimum mix proportion that the upper limit ratio of bentonite is $2.0\%$, polymer is $0.1\%$ considering the funnel viscosity and dispersion agent is $0.05\%$considering the fluid loss of the stabilizing liquid. Also, we select all materials which are consisted of GTC4 as bentonite, KSTP as polymer and Bentocryl 86 as dispersion agent. Based on the results of this study, the optimum mix proportion of the stabilizing liquid is applicable to excavate the deep and massive slurry wall in LNG in-ground tank successfully.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.29-36
• /
• 2002

High fluid concrete unlike OPC concrete is made with various material, and the phase of fresh concrete is considerably different. In order to understand fluidity phase and mix properties of high fluid concrete, concrete is required to access as suspension structure which consists of aggregate and paste. The focus of this paper is to analyze the test results and quantify the effect of mix proportions of molar and fineness modulus of ,and on the properties of fresh mortar. The effect of water-binder ratio, sand-binder ration, content; of ggbs (by mass of total cementitious materials), and various contents of water reducing agent on the yield stress and plastic viscosity of the mix is studied. Based on the experimental results, the following conclusion; can be drawn: (1) The mixing time needed (or high fluid mortar was approximately two times more than that of ordinary portland mortar. (2) The fluidity phase of mortar could be explained by yield stress of mix and the fluidity of mortar. (3) As the content of ggbs increased, yield stress of mortar was decreased and plastic viscosity of it was increased. (4) For the high fluid mortar, it was appeared that sand-binder ratio should be below 1.5.

• 한국도로학회논문집
• /
• 제12권4호
• /
• pp.111-120
• /
• 2010

본 연구는 준고온 공법을 이용한 재생 아스팔트 콘크리트의 강도특성을 평가하기 위해 이루어졌다. 굵은 골재 최대치수 13mm의 화강암과 침입도 60-80인 신규 바인더 60-80을 재생 혼합물을 제조하는데 사용하였다. 배합설계는 RAP(굵은 입자 : 잔입자=6 : 4) 첨가비율 20%와 30%를 사용하였고 GPC, 침입도, 절대점도, 동점도를 준고온 첨가제(Evotherm와 Sasobit)의 첨가 함량을 결정하기 위하여 측정하였다. LD(low-density poly ethylene)를 본 연구에서 준고온 재생 아스팔트 혼합물의 개질제로 사용하였다. 본 연구에서는 8개의 준고온 재생 혼합물(2 RAP함량 ${\times}$ 2 준고온 첨가제 ${\times}$ 2 개질제)뿐만 아니라 2개의 일반 재생 혼합물, 1개의 가열혼합 일반혼합물(control)까지 총 11개의 혼합물을 제조하였다. 변형강도 시험, 간접인장강도 시험, 수분민감성 시험, wheel tracking을 통한 소성변형 시험을 준고온 재생혼합물의 기본 특성을 평가하기 위하여 수행하였다.

• 한국도로학회논문집
• /
• 제16권2호
• /
• pp.19-24
• /
• 2014

PURPOSES : The study objective was to evaluate rheology and physical properties of SBS-modified warm-mix asphalt (WMA) binders in comparison with hot-mix asphalt (HMA) binders. METHODS : Four different SBS polymers were used to prepare polymer-modified asphalt (PMA) binders, and three different warm-mix additives (WAD) were used to prepare a total of 12 WMA PMA binders. The kinematic viscosity was measured at 115, $135^{\circ}C$. The PG was determined using DSR and BBR. The pass/fail (P/F) temperatures for high and low PG grading were evaluated for HMA PMA and WMA PMA binders. RESULTS : PG 76-22 binders could be prepared by modifying the base binder (PG 64-22) using 4.5 wt% of SBS. The kinematic viscosity (KV) of SBS PMA was increased by 3 times higher than that of base asphalt. The SBS PMA with WAD showed 10% lower KV than that of the normal SBS PMA at $115^{\circ}C$ The high P/F temperatures showed almost no difference between HMA PMA and WMA PMA binders. The high P/F temperature showed very high correlations with KV ($R^2$ > 0.97). The result of SBS modification caused increase of low P/F temperature by $2.7^{\circ}C$ on average. CONCLUSIONS : Since the PMA with WAD showed 10% lower KV than normal (HMA) PMA at $115^{\circ}C$, reducing PMA mixture temperature down to a WMA level was possible in this study. The higher KV binders showed the higher P/F temperature. There was almost no change in high P/F temperature due to the use of WAD. The SBS PMA, showing an increased low P/F temperature, might show somewhat poorer performance at low-temperature, even though the lower PG grade was staying at the same level, i.e., $-22^{\circ}C$.

• 한국건축시공학회지
• /
• 제2권4호
• /
• pp.145-152
• /
• 2002

High fluid concrete unlike OPC concrete is made with various material, and the phase of fresh concrete is considerably different. In order to understand fluidity phase and mix properties of high fluid concrete, concrete is required to access as suspension structure which consists of aggregate and paste. The focus of this paper is to analyze the test results and quantify the effect of mix proportions of mortar and fineness modulus of sand on the properties of fresh mortar. The effect of water-binder ratio. sand-binder ration. contents of ggbs (by mass of total cementitious materials). and various contents of water reducing agent on the yield stress and plastic viscosity of the mix is studied. Based on the experimental results, the fellowing conclusions can be drawn: (1) The mixing time needed for high fluid mortar was approximately two times more than that of ordinary portland mortar. (2) The fluidity phase of mortar could be explained by yield stress of mix and the fluidity of mortar. (3) As the content of ggbs increased, yield stress of mortar was decreased and plastic viscosity of it was increased. (4) For the high fluid mortar, it was appeared that sand-binder ratio should be below 1.5.

• 한국건축시공학회지
• /
• 제18권3호
• /
• pp.235-242
• /
• 2018

본 연구에서는 SCC의 높은 민감성으로 인한 품질관리에 어려움을 극복하고자 굵은 골재의 부피, 잔골재의 종류, 단위수량, 공기량, 증점제 사용량 변화 등과 같은 다양한 배합요인이 SCC 특성에 미치는 영향을 분석하여 SCC의 초기물성을 정량적으로 판단할 수 있는 기초자료를 제공하고자 하였다. 실험결과, 항복응력은 굵은 골재 용적율이 증가할수록 낮아졌고 증점제 사용량이 증가할수록 증가하는 것으로 나타났다. 그러나 단위수량, 잔골재 종류 변화, 공기량 증감에 따른 항복응력값의 변화는 없는 것으로 나타났다. 배합요인에 따른 소성 점도는 항복응력과 비슷한 경향을 나타냈다. 또한 항복응력과 슬럼프 플로, $T_{50}$, V-lot와의 상관성 분석결과, 상관관계가 없었고 소성 점도와 $T_{50}$, V-lot와의 상관성은 매우 밀접한 관계가 있는 것으로 나타났는데, 특히, $T_{50}$ 및 V-lot 시간이 줄어들수록 소성 점도도 낮아지는 것을 알 수 있었다.