• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.173-178
• /
• 2005

Recently plastic parts are molded for the purpose of mass production in multi-cavity system. Therefore, designer is usually designing mold that has geometrically balanced runner lay-out for filling balance at each cavity. Although, mold is manufactured with geometrically balanced runner lay-out, there are actually filling imbalances in the cavities. These filling imbalances phenomenon are caused by complicated interaction between melt and mold. In this study, based on previous studies for filling imbalances in cold-runner mold, filling imbalances in hot-runner mold were investigated by CAE and injection molding experiments. ABS and PMMA as amorphous polymer, PA as crystalline polymer were used to compare the filling imbalances. There were different results of CAE and experiment. The filling imbalances decreased as injection rate increased without regard to kind of resins and were lower than the one of cold-runner.

• Design & Manufacturing
• /
• v.9 no.1
• /
• pp.23-26
• /
• 2015

For mass production of plastics, injection molds have multi-cavities. However, filling imbalance between cavity to cavity always has occurred in multi-cavities mold, and this has caused low quality of plastics part. In this study, the closed-loop-control system which can control temperature of hot manifold and nozzle in hot runner mold for filling balance has been suggested, and a series of experiment about difference of filling time and weight in cavity-to-cavity was conducted. As a result of using closed-loop-control system, a remarkable improvement in reducing filling imbalance was confirmed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.598-601
• /
• 2005

Plastic parts are molded for the purpose of mass production in multi-cavity system. Therefore, designer is usually designing molds that has geometrically balanced runner lay-out for filling balance at each cavities. Although, mold is manufactured with geometrically balanced runner lay-out, there are actually filling imbalances in cavities. These filling imbalances phenomenon are caused by complicated interaction between melt and mold. In this study, based on previous studies for filling imbalances in cold-runner mold, filling imbalances in hot-runner mold were investigated by CAE and injection molding experiments. ABS, PMMA as amorphous polymer and PA, PP as crystalline polymer were used to compare the filling imbalances. The filling imbalances decreased as injection rate increased without regard to kind of resins and were lower than the one of cold-runner.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.381-388
• /
• 2003

The paper presents our study of development for multi-cavity preform mold system which consists of hot runner system and valve gate. For this purpose, stretching blow molding process and preform injection process were simulated by Polyflow and Moldflow. Based on various results of the preform injection process analysis, process planning was established. The sectional thickness distribution of preform was optimized. Preform injection mold system was designed by these technical analysis data. Finally, 24-cavity preform mold system was successfully developed.

• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.25-29
• /
• 2008

Almost all injection molds have multi-cavity runner system for mass production, which are designed with geometrically balanced runner system in order to accomplish filling balance between cavity to cavity during processing. However, even though geometrically balanced runner is used, filling imbalance have been observed. Filling imbalance could be decreased by modifying processing conditions such as injections rate, mold temperature, injection pressure, melt temperature that are related to shear, viscosity. In this study, a series of experiment was conducted to investigate filling imbalance variation when modifying runner layout and ploymer and to determine which processing condition influences as the primary cause of filling imbalance in geometrically balanced runner system. The filling imbalance was desreased up to result range of $3{\leq}DFI{\leq}8(%)$ by using a new runner system for balanced filling.

• Design & Manufacturing
• /
• v.1 no.1
• /
• pp.13-16
• /
• 2007

Almost all injection molds have multi-cavity runner system for mass production, which are designed with geometrically balanced runner system in order to accomplish filling balance between cavity to cavity during processing. However, even though geometrically balanced runner is used, filling imbalance have been observed. Filling imbalance could be decreased by modifying processing conditions such as injections rate, mold temperature, injection pressure, melt temperature that are related to shear, viscosity. In this study, a series of experiment was conducted to investigate filling imbalance variation when modifying runner layout and polymer and to determine which processing condition influences as the primary cause of filling imbalance in geometrically balanced runner system.

• Design & Manufacturing
• /
• v.2 no.3
• /
• pp.1-5
• /
• 2008

Plastic parts are molded for the purpose of mass production in injection molding. Therefore designer is usually designing molds that has geometrically balanced hot runner lay-out for filling balance at cavities. Although, mold is manufactured with geometrically balanced runner lay-out, there are actually filling imbalances in cavities. These filling imbalances phenomenon are caused by complicated interaction between melt and mold. In this paper, filling imbalances for internal gear based on injection molding in hot-runner mold were investigated by CAE and injection molding experiences.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1552-1557
• /
• 2010

The cylindrical gear in power window motor assembly is important to doors of automobile. This study is performed for the purpose of getting a manufacturing technique instead of large quantities import and six-cavity mold production. This multi-cavity cylindrical gear is produced under five procedures. The first, mold design of mass-production, the second, making a CAE model for mass-production, the third, manufacturing of sample mold, the fourth, trying-out and measuring of 3 dimensional design, the fifth, acquisition of data analysis and mold modification. Among them, analysis of mass-production using CAE, designing and manufacturing of multi-cavity are successfully performed. In the results, it is concluded that the mold for one gate and eight-cavity based on hot-runner is suitable for making a cylindrical gear.