• Korean Journal of Materials Research
• /
• v.17 no.12
• /
• pp.642-647
• /
• 2007

We investigated dry etching of acrylic (PMMA) in $O_2/N_2$ plasmas using a multi-layers electrode reactive ion etching (RIE) system. The multi-layers electrode RIE system had an electrode (or a chuck) consisted of 4 individual layers in a series. The diameter of the electrodes was 150 mm. The etch process parameters we studied were both applied RIE chuck power on the electrodes and % $O_2$ composition in the $N_2/O_2$ plasma mixtures. In details, the RIE chuck power was changed from 75 to 200 W.% $O_2$ in the plasmas was varied from 0 to 100% at the fixed total gas flow rates of 20 sccm. The etch results of acrylic in the multilayers electrode RIE system were characterized in terms of negatively induced dc bias on the electrode, etch rates and RMS surface roughness. Etch rate of acrylic was increased more than twice from about $0.2{\mu}m/min$ to over $0.4{\mu}m/min$ when RIE chuck power was changed from 75 to 200 W. 1 sigma uniformity of etch rate variation of acrylic on the 4 layers electrode was slightly increased from 2.3 to 3.2% when RIE chuck power was changed from 75 to 200 W at the fixed etch condition of 16 sccm $O_2/4\;sccm\;N_2$ gas flow and 100 mTorr chamber pressure. Surface morphology was also investigated using both a surface profilometry and scanning electron microscopy (SEM). The RMS roughness of etched acrylic surface was strongly affected by % $O_2$ composition in the $O_2/N_2$ plasmas. However, RIE chuck power changes hardly affected the roughness results in the range of 75-200 W. During etching experiment, Optical Emission Spectroscopy (OES) data was taken and we found both $N_2$ peak (354.27 nm) and $O_2$ peak (777.54 nm). The preliminarily overall results showed that the multi-layers electrode concept could be successfully utilized for high volume reactive ion etching of acrylic in the future.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.632-642
• /
• 1998

A method based on finite element discretization is developed for optimizing the polarization profile of PVDF film to create the modal transducer for specific modes. Using this concept, one can design the modal transducer in two-dimensional structure having arbitrary geometry and boundary conditions. As a practical means for implementing this polarization profile without repoling the PVDF film the polarization profile is approximated by optimizing electrode patterns, lamination angles, and poling directions of the multi-layered PVDF transducer. This corresponds to the approximation of a continuous function using discrete values. The electrode pattern of each PVDF layer is optimized by deciding the electrode of each finite element to be used or not. Genetic algorithm, suitable for discrete problems, is used as an optimization scheme. For the optimization of each layers lamination angle, the continuous lamination angle is encoded into discrete value using binary 5 bit string. For the experimental demonstration, a modal sensor for first and second modes of cantilevered composite plate is designed using two layers of PVDF films. The actuator is designed based on the criterion of minimizing the system energy in the control modes under a given initial condition. Experimental results show that the signals from residual modes are successfully reduced using the optimized multi-layered PVDF sensor. Using discrete LQG control law, the modal peaks of first and second modes are reduced in the amount of 12 dB and 4 dB, resepctively.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.27-31
• /
• 2017

AZO/Ag/AZO multi-layer films deposited on glass substrate by RF magnetron sputtering and thermal evaporator have a much better electrical properties than Al-doped ZnO thin films. The multi-layer structure consisted of three layers, AZO/Ag/AZO, the electrical and optical properties of AZO/Ag/AZO were changed mainly by thickness of Ag layers. The optimum thickness of Ag layers was determined to be $90{\AA}$ for high optical transmittance and good electrical conductivity. The Ag layers thickness $90{\AA}$ is an optical transmittance greater than 80% of visible light and the obtained multilayer thin film with the low resistivity of $8.05{\times}10-3{\Omega}cm$ and the low sheet resistance $5.331{\Omega}/sq$. Applying to TCO and Solar electrode will improve efficiency.

• Journal of IKEEE
• /
• v.22 no.1
• /
• pp.149-155
• /
• 2018

In this paper, we used ET(Electrical Tomography) for earth resistivity image reconstruction of vertical multi layer underground model. The earth resistivity is analyzed generally as the parallel multi-layer model, however possibly there happens vertical layer model. Here to find the best electrode array in case of vertical layer underground model, Wenner, Schlumberger, and Dipole-dipole electrode arrays, which are well known electrode arrays used in ET, have been tested. And Gauss-Newton algorithm is used in ET inversion. RMS error analysis shows that Wenner electrode array is best in imaging.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.1
• /
• pp.9-12
• /
• 2006

Al-doped ZnO(AZO)/Ag/AZO multi-layer films deposited on PET substrate by RF magnetron sputtering have a much better electrical properties than Al-doped ZnO single-layer films. The multi-layer structure consisted of three layers, AZO/Ag/AZO, the optimum thickness of Ag layers was determined to be $112{\AA}$ for high optical transmittance and good electrical conductivity. With about $1800{\AA}$ thick AZO films, the multi-layer showed a high optical transmittance in the visible range of the spectrum. The electrical and optical properties of AZO/Ag/AZO were changed mainly by thickness of Ag layers. A high quality transparent electrode, having a resistance as low as $6\;W/{\square}$ and a high optical transmittance of 87% at 550 nm, was obtained by controlling Ag deposition parameters.

• Korean Journal of Materials Research
• /
• v.13 no.8
• /
• pp.503-508
• /
• 2003

The purpose of this study is to investigate the effect of $V_2$$O_{5}$ addition on the Ag and Cu precipitation in the NiCuZn ferrite layers of 7.7${\times}$4.5${\times}$1.0 mm sized multi-layer chip inductors prepared by the screen printing method using 0∼0.5 wt% $V_2$$O_{5}$ -doped ferrite pastes. With increasing the $V_2$$O_{5}$ content and sintering temperature, Ag and Cu oxide coprecipitated more and more at the polished surface of ferrite layers during re-annealing at $840^{\circ}C$. It was thought that during the sintering process, V dissolved in the NiCuZn ferrite lattice and the Ag-Cu liquid phase of low melting point was formed in the ferrite layers due to the Cu segregation from the ferrite lattice and Ag diffusion from the internal electrode. During re-annealing at $840^{\circ}C$, the Ag-Cu liquid phase came out the polished surface of ferrite layers, and was decomposed into the isolated Ag particles and the Cu oxide phase during the cooling process.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.4
• /
• pp.181-184
• /
• 2017

Multilayer ceramics in which piezoelectric layers of $0.90Pb(Zr_{0.48}Ti_{0.52})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.05Pb(Zn_{1/3}Nb_{2/3})O_3$ (0.90PZT-0.05PMS-0.05PZN) stack alternately with silver electrode layers were prepared by an advanced low-temperature co-fired ceramic (LTCC) method. The electrical properties and bonding strength of the multilayers were associated with the interface morphologies between the piezoelectric and silver-electrode layers. Usually, the inner silver electrodes are fabricated by sintering silver paste in multi-layer stacks. To improve the interface bonding strength, piezoelectric powders of 0.90PZT-0.05PMS-0.05PZN with an average particle size of $23{\mu}m$ were added to silver paste to form a gradient interface. SEM observation indicated clear interfaces in multilayer ceramics without powder addition. With the increase of piezoelectric powder addition in the silver paste, gradient interfaces were successfully obtained. The multilayer ceramics with gradient interfaces present greater bonding strength as well as excellent piezoelectric properties for 30~40 wt% of added powder. On the other hand, over addition greatly increased the resistance of the inner silver electrodes, leading to a piezoelectric behavior like that of bulk ceramics in multilayers.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.433.1-433.1
• /
• 2014

The research of graphene, a monolayer of carbon atoms with honeycomb lattice structure, has explosively increased after appeared in 2004. As a result, its high transmittance, mobility, thermal conductivity, and outstanding mechanical and chemical stability have been proved. Especially, many researches were executed about the field of transparent electrode highlighting material of substituting the indium tin oxide (ITO). In addition, qualitative and quantitative improvements have been achieved due to many synthesis methods were discovered. Among them, mostly used method is chemical vapour deposition of graphene grown on copper or nickel. The transmittance, mobility, sheet resistance, and other many properties are completely changed according to these two types of synthesis method of graphene. In this research, considering the difference of characteristics as the synthesis method of graphene, what types of graphene should be used and how to use it were studied. The stacked graphene harvested on copper and multi-layer graphene harvested on nickel were compared and analyzed, as a result, the transmittance of 90% and the sheet resistance of $70{\Omega}{\square}$ was showed even though stacked graphene layers were 4 layers. The reason that could bring these results is lowered sheet resistance due to stacked monolayer graphenes. Moreover, light output power of the three stacked graphene spreading layer shows the highest value, but light-emitting diode with multi-layer graphene died out from 12mA due to also its high sheet resistance. Therefore, we need to clarify about what types of graphene and how to use the graphene in use.

• Proceedings of the KIEE Conference
• /
• 2006.07e
• /
• pp.89-90
• /
• 2006

Recent earth systems not only make earth resistance decreased by installing earth electrode but also are demanded by earth construction for the protection of human life and equipments through total investigation about circumstances. Layer constructions in Jeju island consist of multi-layer of scoria, rocks and shale except clay layers on the surface, which needs the construction of the coring earth electrode suitable in the condition of the area. For this reason, we've used the coring earth electrode. But the coring earth electrode is expected to slow down the performance of this equipment according to the progress of time changing the effects. It is also applied for the stability of earth system construction and management after the construction work analyzing the condition of the earth system. Therefore, this is actually focused on the analysis on measuring the earth resistance and the soil resistivity that cover the range where the remarkable contrast can be expected to be seen in the layer structures.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.1
• /
• pp.33-38
• /
• 2000

In this study, multilayer piezoelectric actuators were fabricated with 75 layers by a conventional multi-layer capacitor (MLC) techniques, using 70Ag/30Pd paste as an internal electrode which can be sintered at low temperature and have cost down effect in mass productions. The multilayer piezoelectric actua-tors had no defects such as diffusions of internal electrode to ceramic bodies and shortages of internal electrodes. The multilayer piezoelectric actuators did not show the crack in the ceramics parts and the gapping phenomena in the external eletrodes when Ag paste was used as external electrodes. The multilayer piezoelectric actuators showed a maximum displacement of 4${\mu}{\textrm}{m}$ at 100V dc voltage and kept the maximum displacement constant for 300 seconds. The multilayer piezoelectric actuators showed good matching properties between ceramic bodies and AgPd internal electrodes. We confirmed the possibility of large-scaled production of the multilayer piezoelectric actuators with superior electrical properties and cost down effect using 70Ag/30Pd paste as an internal electrodes.