• 한국전기전자재료학회논문지
• /
• 제25권1호
• /
• pp.58-61
• /
• 2012

In our report a relatively simple process for fast nano-texturing of p-type(100) CZ- silicon surface using silver catalyzed wet chemical etching in aqueous hydrofluoric acid (HF) and hydrogen peroxide solution($H_2O_2$) at room temperature. The wafers were saw-damaged by NaOH(6 wt%) at $60^{\circ}C$ for 150s. To obtain a nano-structured black surface, a thin layer of silver with thickness of 1 - 10 nm was deposited on the surfaces by evaporation system. After this process the samples were etched in HF : $H_2O_2$ : $H_2O$ = 1:5:10 at room temperature for 80s - 220s. Due to the local catalytic of the Ag clusters, this treatment results in the nano-scale texturing on the surface. This resulted in average reflectance values less than 9% after the silver on the surface of the wafers were removed.

• 한국결정성장학회지
• /
• 제23권2호
• /
• pp.86-92
• /
• 2013

나노결정질 다이아몬드 박막 증착을 위한 전처리 공정으로 $SF_6/O_2$ 유도결합 플라즈마를 이용하여 Si 기판 표면을 texturing하였다. $SF_6/O_2$ 플라즈마 texturing은 2~16 범위의 매우 넓은 정규화된 표면 조도 선택성을 제공할 수 있음을 확인하였다. Texturing된 Si 기판 표면의 나노 다이아몬드 입자 seeding 이후 기존 기계적 연마 전처리에 비해 현저히 향상된 ${\sim}6.5{\times}10^{10}cm^{-2}$의 높은 핵형성 밀도를 확보하였다.

• 한국생산제조학회지
• /
• 제25권6호
• /
• pp.410-420
• /
• 2016

The geometric dimension and shape of microchannels that are formed during surface texturing are widely studied for applications in flow control, and drag and friction reduction. In this research, a new method for controlling the deformation of U channels during micro-rolling-based surface texturing was developed. Since the width of the U channels is almost constant, controlling the depth is essential. A calibration procedure of initial rolling gap, and proportional-integral PI controllers and a linear interpolation have been applied simultaneously to control the depth. The PI controllers drive the position of the pre-U grooved roll as well as the rolling gap. The relationship between the channel depth and rolling gap is linearized to create a feedback signal in the depth control system. The depth of micro channels is studied on A2021 aluminum lamina surfaces. Overall, the experimental results demonstrated the feasibility of the method for controlling the depth of microchannels.

• 전기화학회지
• /
• 제14권4호
• /
• pp.191-195
• /
• 2011

Wet chemical etching methods were utilized to conduct Si surface texturing, which could enhance photoelectrochemical hydrogen generation rate. Two different etching methods tested, which were anisotropic metal-catalyzed electroless etching and isotropic etching. The Si nano-texture that was fabricated by the anisotropic etching showed ~25% increase in photocurrent for H2 generation. The photocurrent enhancement was attributed to the reduced reflection loss at the nano-textured Si surface, which provided a layer of intermediate density between water and the Si substrate.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.270-270
• /
• 2010

결정질 실리콘 태양전지는 표면반사에 의한 광 에너지 손실을 최소화 시키고자 식각을 통한 표면 조직화(texturing)가 이루어진다. 단결정 실리콘 웨이퍼의 경우 알칼리 용액(alkali solution)을 사용하여 이방성 식각(anisotropic etching)을 함으로써 표면에 피라미드를 형성하고 광 포획(light trapping) 효과에 의해 반사율을 줄이게 된다. 그러나 피라미드 형성을 통한 반사율 감소에는 한계를 가지고 있다. Metal assisted etching을 기반으로 한 새로운 형태의 텍스쳐링인 nano texturing은 피라미드가 이루어진 표면에 수많은 nm사이즈의 구조를 형성시킴으로써 표면에서의 반사율을 현저히 감소시킨다. 먼저 $AgNO_3$용액으로 웨이퍼 표면에 Ag입자를 코팅한 후, 그 웨이퍼를 다시 $HF/H_2O_2$ 용액으로 일정시간 동안 식각을 거치게 된다. 그로 인해 표면에는 수 nm 사이즈의 구조물들이 피라미드 위에 생성되고, $AgNO_3$의 농도 및 식각 시간에 따라 그 구조물의 크기 및 굵기가 달라진다. 결과적으로 평균 10%이상의 반사율을 보이던 기존 텍스쳐링 웨이퍼에서 3%이하의 낮은 반사율을 얻을 수 있었다. 또한 이런 nano texturing을 n-emitter 형성 공정 등에 따른 영향과 carrer lifetime에 대하여 연구하였다.

• Current Photovoltaic Research
• /
• 제6권1호
• /
• pp.1-11
• /
• 2018

Current major photovoltaic (PV) market share (> 60%) is being occupied by the multicrystalline (mc)-silicon solar cells despite of low efficiency compared to single crystalline silicon solar cells. The diamond wire sawing technology reduces the production cost of crystalline silicon solar cells, it increases the optical loss for the existing mc-silicon solar cells and hence its efficiency is low in the current mass production line. To overcome the optical loss in the mc-crystalline silicon, caused by the diamond wire sawing, next generation texturing process is being investigated by various research groups for the PV industry. In this review, the limitation of surface structure and optical loss due to the reflectivity of conventional mc-silicon solar cells are explained by the typical texturing mechanism. Various texturing technologies that could minimize the optical loss of mc-silicon solar cells are explained. Finally, next generation texturing technology to survive in the fierce cost competition of photovoltaic market is discussed.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.345-346
• /
• 2013

InGaN material is being studied increasingly as a prospective material for solar cells. One of the merits for solar cell applications is that the band gap energy can be engineered from 0.7 eV for InN to 3.4 eV for GaN by varying of indium composition, which covers almost of solar spectrum from UV to IR. It is essential for better cell efficiency to improve not only the crystalline quality of the epitaxial layers but also fabrication of the solar cells. Fabrication includes transparent top electrodes and surface texturing which will improve the carrier extraction. Surface texturing is one of the most employed methods to enhance the extraction efficiency in LED fabrication and can be formed on a p-GaN surface, on an N-face of GaN, and even on an indium tin oxide (ITO) layer. Surface texturing method has also been adopted in InGaN-based solar cells and proved to enhance the efficiency. Since the texturing by direct etching of p-GaN, however, was known to induce the damage and result in degraded electrical properties, texturing has been studied widely on ITO layers. However, it is important to optimize the ITO thickness in Solar Cells applications since the reflectance is fluctuated by ITO thickness variation resulting in reduced light extraction at target wavelength. ITO texturing made by wet etching or dry etching was also revealed to increased series resistance in ITO film. In this work, we report a new way of texturing by deposition of thickness-optimized ITO films on ITO nano dots, which can further reduce the reflectance as well as electrical degradation originated from the ITO etching process.

• 한국결정성장학회지
• /
• 제20권1호
• /
• pp.7-11
• /
• 2010

단결정 실리콘 태양전지의 광학적 손실을 감소시키는 표면 텍스쳐링은 최종 셀의 효율을 향상시키기 위하여 매우 중요하다. 본 연구에서는 2-step texturing의 공정으로 기존의 텍스쳐링에서 이루어진 피라미드에 수 많은 sub-micrometer 사이즈의 구조를 형성시켰다. $AgNO_3$ 용액으로 웨이퍼 표면에 Ag코팅을 한 후, 그 웨이퍼를 다시 HF/$H_2O_2$ 용액으로 수십초 동안 식각을 거치게 된다. 결과적으로, 피라미드 위에 생성된 수 nm사이즈의 구조물들은 $AgNO_3$의 농도 및 식각 시간의 변화에 의해 그 크기와 굵기가 변화하는 것을 알 수 있었다. 웨이퍼의 표면이 2-step texturing에 의해 식각이 이루어지면 연잎의 거친 표면과 비슷해지고, 그 결과 평균 10% 이상의 반사율을 보이던 기존 웨이퍼에서 3% 이하의 낮은 반사율을 얻을 수 있었다. 이는 일반적인 텍스쳐링과 anti-reflection coating을 거친 웨이퍼의 반사율보다 낮은 결과이다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.43-44
• /
• 2015

Electrodeposited Ni and Ni-SiC composite coatings were prepared on Cu substrates by using the Ni-Sulfamate electrolytic bath. Thus prepared samples were subjected for the two different types of post surface modification techniques; i.e. Laser Surface Texturing (LST) and Ultrasonic Nano Surface Modification (UNSM), respectively in order to investigate their effects on surface and interface related properties of the coatings. Hemispherical dimples, with 80 to 200 um dimple spacing, were created and examined on the surfaces of the materials studied. The results revealed that micro-surface texturing with 150 um dimple spacing considerably improved the coefficient of friction. Dimple spacing accuracy and incorporated second phase ceramic particles both contributed significantly to reduction in coefficient of friction. On the other hand, application of UNSM considerably modified the surface topography, led to increase the Vickers microhardness, and reduced the wear and coefficient of friction as compared to non UNSM treated Ni and Ni-SiC samples.

• 한국정밀공학회지
• /
• 제31권12호
• /
• pp.1127-1132
• /
• 2014

Fast tool servo (FTS) is an enabling technology to fabricate various shapes of functional surface geometries in a precise and controllable manner. FTS can be also employed as a straightforward and efficient surface treatment way of making such products more durable. In this work, process characteristics using high-precision FTS-based surface texturing were qualitatively and quantitatively investigated to provide a class of surface design rule. The morphologies of surfaces processed with different conditions were first examined by observing the resultant 2D/3D surface profiles. In addition, the effects of the surface treatment using FTS on hardness and wear properties were characterized and compared to those without treatment.