• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.934-937
• /
• 2004

The purpose of this study is to present a fundamental data to get the noise reduction method of subway station in Gwang-ju city. Subway noise level measurement and questionnaire on the satisfaction of sound condition were carried out. The results show that the noise level of the subway station and the noise reduction effect installed by screen door is over 10 dB(A).

• Journal of Astronomy and Space Sciences
• /
• v.24 no.4
• /
• pp.409-416
• /
• 2007

The ambiguity and performance of range measurement for COMS using tone standard was analyzed with assuming that satellite is operating at transfer-station and on-station. From the results of analysis, it was shown that the ambiguity was reduced when low frequency ratio between tone signals and large number of minor tones are applied. It was also found that using the narrow noise bandwidth leads to decrease the ambiguity. As a result, required performance of range measurement for COMS can be satisfied when the noise bandwidth is set as 2Hz for transfer-station and 1Hz for on-station, respectively.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.10
• /
• pp.968-975
• /
• 2010

The high interest for the ground vibrations which is caused by the train service is risen. When the trains are passed, a serious force is applied to ground and the caused vibration is propagated to the area of the building by the ground and rocks. This vibration comes to feel in the residents with the direct vibration, it is radiated in sound. The caused vibration and radiated sound affect the human's life, and this vibration brings about the operation interruption of the equipment which is sensitive to the vibration, or will bring about the structural damage of the building. In this study, the effect of the vibrations caused by the passing trains on the railway station and buildings is investigated by vibration measurement. Indoor and outdoor measurement is carried out by each trains.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.6-11
• /
• 2007

Packaged power station (PPS) is a stationary diesel engine generator set and developed for the supply of electric power to small villages, islands and factories etc. Therefore, the PPS is closely installed to residence area and sometimes cause the environmental noise problems. In this paper, environmental noise analysis was performed for the power plant with 28 sets of PPS. The initial analysis results showed the some difference between the measurement and analysis because of the inaccurate noise source data. To improve the accuracy of analysis, main noise sources were inversely estimated using the in-situ measurement data in the vicinity of PPS and steam boiler. As the results of re-analysis, the good agreement was obtained and it was concluded that the noise levels exceed the specified noise limit in residence area. In order to reduce the noise, the several methods such as geometry alteration of inlet duct, application of hybrid-type silencer and noise protection barrier were suggested and verified with the confirmed analysis model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.703-705
• /
• 2013

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.861-864
• /
• 2005

Performing accurate and repeatable low frequency noise measurement is critical for modeling and simulation of flicker noise. Through the accurate and repeatable on-wafer measurement, low frequency noise characteristics of the 0.18 ${\mu}m$ n-MOSFETs are discussed. And on-wafer flicker noise measurement system is presented. The on-wafer measurement system consists of cascade probe station, low noise current amplifier (SR570), and dynamic signal analyzer (HP35670A).

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.200-204
• /
• 2005

A few intake stations have vibration problems caused by pumps, motors and pipes. The vibration transffered from pumps, motors and pipes excites buiding severely. Therefore, the crack is generated on building wall and people who work at intake station are damaged. In this paper, the vibration and noise have been measured and analyzed for pumps, motors, pipes and building at intake station. Also, the cause of vibration and noise is identified. Finally, the reference of vibration and noise is established using results of measurement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.433-438
• /
• 2010

Reactor vessel internals comprehensive vibration assessment program(RVI CVAP) is one of the necessary tests to ensure the safety of nuclear power plants. RVI CVAP of U.S. Nuclear Regulatory Commission Regulatory Guide 1.20(U.S. NRC R.G. 1.20) consists of the analysis, measurement, and inspection. One of the core technologies of the measurement program for RVI CVAP is to select suitable sensors. We analyzed RVI design data of Palo Verde nuclear generating station(U.S.) and Yonggwang nuclear generating station(Korea) and investigated measuring sensors used in both of them; moreover, we investigated sensors used for measurement of RVI CVAP for the last 20 years throughout the world. Based on these results, we selected the most suitable sensors for RVI CVAP in Advanced Power Reactor 1400(APR1400).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.883-886
• /
• 2005

This paper proposed a wireless measurement system (WMS) for an effective condition monitoring using wireless communication. WMS consists of two parts: transmitter(TM) acquired a dynamic signal from physical system using ICP type accelerometer sensor. An acquired signal modulated through the low/high pass filter and amplifier in DAQ board, which converted to digital signal. Embedded board(E-board) transferred digital signals to base station(BS) through the socket IEEE.802.11.b. BS is adopted IOCP server structure. Because it can acquired signal well during transferred digital signal. Signal processing used LabVIEW Library, BS(server) designed to realize multi-thread using visual C++.NET for 1 many meaning data processing

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.88-91
• /
• 2007

Turnout system is a mechanical installation enabling trains to be guided from one track to another which is consists of point blades, common crossing and guard rail etc. These structural feature causes vibration, noise and damages while railroad car wheel is passes by. A tilting train is a train with a tilting mechanism that enables increased speed on regular railroad tracks. The aim of this paper is to study a characteristics of the shock-vibration and noise of tilting and existing train passes by turnout systems. To analyze and assesment, noise and vibration measurement was carried out at the Naesu-station of Chungbuk-line which equipped with cast manganese crossing and built-up crossing and Illo-station of Honam-line which equipped with cast manganese crossing.