• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.6
• /
• pp.524-530
• /
• 2008

The spin valve tunneling magnetoresistance (SV-TMR) sensor performance is analyzed using Stoner-Wohlfarth model for the detection of eddy current signals in nondestructive testing applications. The SV-TMR response in terms of the applied AC magnetic field dominantly generates the second harmonic amplitude in hard axis direction. The second harmonic eddy current signal detection using SV-TMR sensor shows higher performance than that of the coil sensor at lower frequencies. The SV-TMR sensor with high sensitivity gives a good solution to improve the low frequency performance in comparison with the inductive coil sensors. Therefore, the low frequency eddy current techniques based on SV-TMR sensors are specially useful in the detection of hidden defects, and it can be applied to detect the deeply embedded flaws or discontinuities in the conductive materials.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.424-430
• /
• 2008

A new active vibration measurement system in electric power transmission line is presented, using in the nondestructive test. With a permanent magnet and a couple of coils, the system exerts impact force to a test object and in turn picks up the vibration of the object. The natural frequency with the amplitude obtained from the system are used as a basis for the detection of defects in the object. The system is controlled by an electronic device designed to facilitate the fully automated testing process with consistent repeatability and reliability which are essential to the nondestructive test. The system is expected to be applied to the wide area of defect detection including the classification of mechanical parts in production and inspection processes.

• Journal of Biosystems Engineering
• /
• v.40 no.1
• /
• pp.67-77
• /
• 2015

Purpose: Fungal secondary metabolite (mycotoxin) contamination in foods can pose a serious threat to humans and animals. Spectroscopic techniques have proven to be potential alternative tools for early detection of mycotoxins. Thus, the aim of this review is to provide an overview of the current developments in nondestructive food safety testing techniques, particularly regarding fungal contamination testing in grains, focusing on the application of spectroscopic techniques to this problem. Methods: This review focuses on the use of spectroscopic techniques for the detection of fungi and mycotoxins in agricultural products as reported in the literature. It provides an overview of the characteristics of the main spectroscopic methods and reviews their applications in grain analysis. Results: It was found that spectroscopy has advantages over conventional methods used for fungal contamination detection, particularly when combined with chemometrics. These advantages include the rapidness and nondestructive nature of this approach. Conclusions: While spectroscopy offers many benefits for the detection of mycotoxins in agricultural products, a number of limitations exist, which must be overcome prior to widespread adoption of these techniques.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.3
• /
• pp.282-289
• /
• 2010

Most nondestructive testing techniques require good contact between the sensor and tested concrete surface to obtain reliable data. But the surface preparation is often very time and labor consuming due to the rough surface or limited access of concrete structures. One approach to speed up the data collection process is to eliminate the need for physical contact between the sensor and tested structure. Non-contact air-coupled sensing technique can be a good solution to this problem. An obvious advantage of the non-contact air-coupled sensing technique is which can greatly speed up the data collection in field and thus the damage detection process can be completed very rapidly. In this article, recent developments in non-contact air-coupled sensing technique for rapid detection of damages in concrete structures are summarized to evoke interest, discussion and further developments on this technique to a NDT research community in Korea. It is worth noting that the works in this article have been published in the types of thesis, proceedings, and journals. All published sources are cited in the text and listed in reference.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.2 no.2
• /
• pp.17-31
• /
• 1983

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1413-1416
• /
• 2005

An infrared temperature sensor module developed for the detection of defects in a plate was modified to use in a cylinder. A set of optical fiber leads and a mechanism maintaining sensor-object distance constant were utilized for the modification of the IR sensor module. The detection performance was experimentally investigated, and the measured temperature was also compared with computed temperature distribution. The experimental outcome indicates that the detection of a simulated defect is readily available. The temperature distribution is better for defect detection than that with the previous device. In addition, the measured distribution is comparable to the calculated one using a heat conduction equation. The developed device of defect detection is suitable to be utilized in chemical processes where most of vessels and piping systems are in the shape of a cylinder.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.8 no.1
• /
• pp.30-37
• /
• 1988

Interfaces, both grain boundaries and phase boundaries, play a very important role in the mechanical behavior of structural materials. The problemis particularly intense in composite materials where interfaces play a primary role in the meehanical response of the composites. This paper will concentrate on the approaches to perform nondestructive evaluation of the interfaces in a man nor in which some measure of the mechanical behavior of the interface can be established. Some of the possible approaches that may have potential for the nondestructive evaluation of interfaces are optical, electronic/ electrical, and acoustic approaches.

• Journal of Biosystems Engineering
• /
• v.39 no.4
• /
• pp.357-365
• /
• 2014

Purpose: The continued increase in the world population has triggered an increased demand for food. Cereal grains, flour, and their products constitute the staple diet for most of the world's population. This high demand for food, particularly for cereal-based products, has been exploited for commercial gain through adulteration of food materials. We provide a thorough review of the current developments and limitations of modern, nondestructive analytical techniques used for detection of adulterants in cereals and their products and compare them with conventional methods. Results: Adulterated food poses a serious health risks to humans, animals, and the ecosystem in general. Over the last few decades, the adulteration industry has developed fraudulent practices that often outsmart conventional methods of detection and quality control. Therefore, technological advancements to aid in detection and measurement of adulterants in food products and to ensure food quality and safety are critically important to consumers worldwide. Conclusion: There is a continuous demand for development of nondestructive technology to improve the accuracy and efficiency of detection, measurement, and qualification of adulterants in cereals and other food materials.

• Steel and Composite Structures
• /
• v.50 no.1
• /
• pp.89-105
• /
• 2024

Multichannel analysis of surface waves (MASW) method has exhibited broad application prospects in the nondestructive detection of interfacial debonding in steel-concrete composite structures (SCCS). However, due to the structural diversity of SCCS and the high stealthiness of interfacial debonding defects, the feasibility of MASW method needs to be investigated in depth. In this study, synthetic parametric study on MASW nondestructive debonding detection for SCCSs is performed. The aim is to quantitatively analyze influential factors with respect to structural composition of SCCS and MASW measurement mode. First, stress wave composition and propagation process in SCCS are studied utilizing 2D numerical simulation. For structural composition in SCCS, the thickness variation of steel plate, concrete core, and debonding defects are discussed. To determine the most appropriate sensor arrangement for MASW measurement, the effects of spacing and number of observation points, along with distances between excitation points, nearest boundary, as well as the first observation point, are analyzed individually. The influence of signal type and frequency of transient excitation on dispersion figures from forwarding analysis is studied to determine the most suitable excitation signal. The findings from this study can provide important theoretical guidance for MASW-based interfacial debonding detection for SCCS. Furthermore, they can be instrumental in optimizing both the sensor layout design and signal choice for experimental validation.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.295-301
• /
• 2000

Various nondestructive prospecting method were applied to detect the flaws of concrete structure, but the satisfactory result could not be obtained, yet. Fracture and cavities existing concrete structure will have a bad effect on physical and mechanical characteristic of concrete. This study deal with detection of flaws using seismic first arrival and various inversion method in theoretical model. And ultrasonic seismic method is tried to experimental model to detect fracture and cavity.