• Journal of the Korean Society of Visualization
• /
• v.19 no.1
• /
• pp.88-93
• /
• 2021

For a flow normal to a circular disk, the flow separation occurs from the edge of the disk and the flow recirculation zone exists behind the disk. Many existing studies conducted simulations of flow normal to a circular disk under low Reynolds numbers. Some studies performed LES or DES simulations under high Reynolds numbers. However, comparative study for different RANS models for high Reynolds numbers is very limited. This study presents numerical simulations of a flow normal to a circular disk using Realizable k-ε model and SST k-ω model. The recirculation bubble length and drag coefficient were compared with the experimental data. The SST k-ω model showed the excellent predictions for the recirculation bubble length and drag coefficient.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.144-148
• /
• 1998

Using a test apparatus developed Lrt the laboratory, frictional characteristics of natural rubbers have been analyzed by experimental study. Friction coefficient has been calculated from the measured normal force and friction force under various speeds, loads, and temperatures. The relations between the various operating conditions and friction coefficients have been verified. Especially, drag friction due to the visco-elastic behavior of the rubber has been observed in this analysis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.4
• /
• pp.308-315
• /
• 2007

This study is performed to find out the climb performance of light airplane, Chang Gong-91, as a part of flight test to acquire the certification. Chang Gong-91 is a 5-passenger light aircraft of normal category with single reciprocating engine, and the first officially certified by Korean Ministry of Construction and Transportation in 1993. These flight test procedure and data for climb performance are used to get type certification. We have got maximum climb rate for operating altitude, best angle of climb speed, best rate of climb speed, and absolute ceiling of Chang Gong-91 using drag polar data reduction method from sawtooth climb flight data. Also we compare the form drag coefficient from the results of climb performance and Oswald's effectiveness coefficient to design values using lift-drag curve of light airplane.

• Journal of KSNVE
• /
• v.5 no.3
• /
• pp.303-311
• /
• 1995

Tests on flow-induced vibration of inclined cylinders in uniform flow were performed in the cavitation tunnel at the Korea Instituteof Machinery and Metals. The test program was intended to investigate flow-induced vibration characteristic of the cylinders with three different inclined angles of 10$^\circ$, 20$^\circ$ and 30$^\circ$ and to estimate the fluid force coefficients acting on the cylinders. Important observations are as follows: 1) Numal drag is dominant compared with viscous drag for the inclined angle over 20.deg. and it has the value from 1.7 to 2.0 as was observed by other researchers. 2) Lift force coefficient has large value at the lock-in range determined by 4$\Theta/f_nD$<8. Measured maximum lift force coefficients at the inclined angle of 30.$^\circ$ and 20$^\circ$ were 0.9 and 0.4 respectively.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.279-282
• /
• 2011

Projectile can be damaged during the storage and handling. Maximum range calculation of the ammunition was performed on the assumption that each projectiles have 1.5mm/3.3mm axisymetric dent on the surface. Drag coefficient for trajectory calculation was delivered from CFD using commercial software FLUENT. In the result of CFD, damaged projectiles those have 1.5mm/3.3mm axisymetric dent have similar drag coefficient compare with normal projectile in the region of subsonic. But, in supersonic region, drag coefficient was increased 3%, 9% each in average. In the result of trajectory calculation, Maximum rage was decreased 1%, 3% each.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.3
• /
• pp.171-181
• /
• 2017

Two-phase cross flow exists in many shell-and-tube heat exchangers such as condensers, evaporators, and nuclear steam generators. The drag force acting on a tube bundle subjected to air/water flow is evaluated experimentally. The cylinders subjected to two-phase flow are arranged in a normal square array. The ratio of pitch to diameter is 1.35, and the diameter of the cylinder is 18 mm. The drag force along the flow direction on the tube bundles is measured to calculate the drag coefficient and the two-phase damping ratio. The two-phase damping ratios, given by the analytical model for a homogeneous two-phase flow, are compared with experimental results. The correlation factor between the frictional pressure drop and the hydraulic drag coefficient is determined from the experimental results. The factor is used to calculate the drag force analytically. It is found that with an increase in the mass flux, the drag force, and the drag coefficients are close to the results given by the homogeneous model. The result shows that the damping ratio can be calculated using the homogeneous model for bubbly flow of sufficiently large mass flux.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.3
• /
• pp.124-131
• /
• 2015

The good performance of a vortex shedder is defined by strong and stable vortex generated under the condition of most linearity in Strouhal number and low power loss. In this paper, the flow past a bluff body of circular cylinder with a slit normal to the flow has been analyzed focusing on drag coefficient, linearity of Strouhal number and flow resistance (K-factor). The ANSYS/FLUENT package is used for flow simulation and the integration method of computational code to iSIGHT platform is employed for automated design cycle. This study results the design with (0.20~0.267) blockage ratio and 0.10 slit ratio as the best shedder for vortex flowmeter and this results are in well agreement with the experiment. As the combination of GAMBIT, FLUENT, and iSIGHT substitutes the design parameters automatically according to the input data, this method designs effectively the vortex shedder with less design cycle time and low manufacturing cost eliminating the human intervention bottleneck.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.193-198
• /
• 1999

Applying design methodology, new type friction tester has been developed. Functional analysis has been executed and functional structure were constructed during the conceptual design. Optimal solution has been selected and a proto model has been manufactured according to the conceptual design. Using the tester developed in the laboratory, frictional characteristics of natural rubbers have been experimentally analyzed. Friction coefficient has been calculated from the measured normal force and friction force under various speeds, loads, and temperatures. The corelations between the various operating conditions and friction coefficients have been verified. Especially, drag friction due to the visco-elastic behavior of the rubber has been observed in this analysis.

• Corrosion Science and Technology
• /
• v.7 no.5
• /
• pp.283-287
• /
• 2008

The drag reduction agency (DRA) for gas pipeline, a novel method used for reducing friction or drag on a gas flowing to increase the transmission efficiency of gas pipeline, is a more flexible and economical technology than internal flow efficient coatings. In this paper, an effective DRA has been developed in Authors' Institute by analyzing the hydrodynamic friction resistance on internal gas pipeline and then studying the work mechanism and molecular structure of DRA. In the meantime, a group of property test for selecting DRA material has been determined, including viscosity, contact angle, volatility, corrosion, slab extending, and flow behavior in horizontal tube. The inhibition efficiency and drag reduction efficiency of the developed DRA have been investigated finally based on the relevant test methods. Results of corrosion test show that the developed DRA has very good inhibition effect on mild steel by brushing a thin layer of DRA on steel specimens, giving inhibition efficiency of 91.2% and 73.1% in 3%NaCl solution and standard salt fog environment respectively. Results of drag-reducing test also show that the Colebrook formula could be used to calculate friction factors on internal pipes with DRA as the Reynolds number is in the range of $0.75\times10^5\sim2.0\times10^5$. By comparing with normal industrial pipes, the friction resistance coefficient of the steel pipe with DRA on internal wall decreases by 13% and the gas flux increases by 7.3% in testing condition with Reynolds number of $2.0\times10^5$.

• 한국가시화정보학회:학술대회논문집
• /
• 2005.12a
• /
• pp.17-22
• /
• 2005

An experimental study was carried out to investigate the effect of local ultrasonic forcing on a turbulent boundary layer. Stereoscopic particle image velocimetry (SPIV) was used to probe the characteristics of the flow. A ultrasonic forcing system was made by adhering six ultrasonic transducers to the local flat plate. Cavitation which generates uncountable minute air-bubbles having fast wall normal velocity occurs when ultrasonic was projected into water. The SPIV results showed that the wall normal mean velocity is increased in a boundary layer dramatically and the streamwise mean velocity is reduced. The skin friction coefficient ($C_{f}$) decreases $60\%$ and gradually recovers at the downstream. The ultrasonic forcing reduces wall-region streamwise turbulent intensity, however, streamwise turbulent intensity is increased away from the wall. Wall-normal turbulent intensity is almost the same near the wall but it increases away from the wall, In tile vicinity of the wall, Reynold shear stress, sweep strength and production of turbulent kinetic energy were decreased. This suggests that the streamwise vortical structures are lifted by ultrasonic forcing and then skin friction is reduced.