• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.169-176
• /
• 2013

To generate the walking path of a humanoid robot in an unknown environment, the shapes of obstacles around the robot should be detected accurately. However, doing so incurs a very large computational cost. Therefore this study proposes a method to classify the obstacle shape into three types: a shape small enough for the robot to go over, a shape planar enough for the robot foot to make contact with, and an uncertain shape that must be avoided by the robot. To classify the obstacle shape, first, the range and the number of the obstacles is detected. If an obstacle can make contact with the robot foot, the shape of an obstacle is accurately derived. If an obstacle has uncertain shape or small size, the shape of an obstacle is not detected to minimize the computational load. Experimental results show that the proposed algorithm efficiently classifies the shapes of obstacles around the robot in real time with low computational load.

• Journal of the Korean Institute of Gas
• /
• v.12 no.1
• /
• pp.54-61
• /
• 2008

Experimental investigations were performed to assess the influences of different multiple obstacles on flame propagation in a rectangular confinement. Three different multiple obstacles were used: circular, triangular and square cross-sections with blockage ratios of 15% and 30%. The same method described in Park et al. [13] to investigate the interaction between the propagating flame and the obstacle was applied. Before the freely propagating flame impinged on the obstacle, the flame propagation speed remains close to the laminar burning velocity, regardless of the obstacles used. The reported data revealed that the trend in increase of the local flame propagation speed is a result of the interaction between the obstacle and the propagating flame front behind the obstacle. The local speed was found to increase from a circular to a triangular and a square obstacle. The mean flame speed was found to be less dependent on both the obstacle types and the different blockage ratios used.

• Agricultural and Biosystems Engineering
• /
• v.2 no.2
• /
• pp.69-74
• /
• 2001

Detection of operation lines in farm works, object recognition and obstacle avoidance are essential pre-requisite technologies for unmanned agricultural machinery. A CCD camera, which has been largely used for these functions, is expensive and has difficulty in real-time signal processing. In this study, a laser range sensor was selected as the guiding vision for unmanned agricultural machinery such as a tractor. To achieve this capability, algorithms for distance measurement, signal filtering, object recognition, and obstacle avoidance were developed. Computer simulations were carried out to evaluate performance of the algorithms. Experiments were also conducted with various materials and shapes, Laser beam lost its intensity for poor reflective materials, resulting in less range value than actual, so a compensation technique was considered to be necessary. Object detection system was fabricated on an agricultural tractor and the performance was evaluated. As test result for obstacle detection and avoidance in field, to detect and avoid obstacle for path finding with guiding system for unmanned agricultural machinery was enable.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.98-106
• /
• 1991

Future generation of robots will be considerably more autonomous than present robotic systems. The main objective of research on theoretical problems in robotics is to endow robotics system with basic capabilities they will need to operate in an intelligent and autonomous manner. This paper discusses the problem of collision free movement of robot manipulator. It is formulated in path planning with obstacle avoidance expressed in the term of the distance between convex shapes in the three dimensional space. The examples are given to illustrate the main feature of the method.

• Wind and Structures
• /
• v.9 no.4
• /
• pp.315-330
• /
• 2006

Flow and scalar dispersion around Cheomseongdae are numerically investigated using a three-dimensional computational fluid dynamics (CFD) model with the renormalization group (RNG) $k-{\varepsilon}$ turbulence closure scheme. Cheomseongdae is an ancient astronomical observatory in Gyeongju, Korea, and is chosen as a model obstacle because of its unique shape, that is, a cylinder-shaped architectural structure with its radius varying with height. An interesting feature found is a mid-height saddle point behind Cheomseongdae. Different obstacle shapes and corresponding flow convergences help to explain the presence of the saddle point. The predicted size of recirculation zone formed behind Cheomseongdae increases with increasing ambient wind speed and decreases with increasing ambient turbulence intensity. The relative roles of inertial and eddy forces in producing cavity flow zones around an obstacle are conceptually presented. An increase in inertial force promotes flow separation. Consequently, cavity flow zones around the obstacle expand and flow reattachment occurs farther downwind. An increase in eddy force weakens flow separation by mixing momentum there. This results in the contraction of cavity flow zones and flow reattachment occurs less far downwind. An increase in ambient wind speed lowers predicted scalar concentration. An increase in ambient turbulence intensity lowers predicted maximum scalar concentration and acts to distribute scalars evenly.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.4
• /
• pp.341-347
• /
• 2011

This paper presents the performance evaluation. optimal design. and complex obstacle detection of an overlapped ultrasonic sensor ring by introducing a new concept of effective beam width. It is assumed that a set of ultrasonic sensors of the same type are arranged along a circle of nonzero radius at regular spacings with their beams overlapped. First, the global positional uncertainty of an overlapped ultrasonic sensor ring is expressed by the average value of local positional uncertainty over the entire obstacle detection range. The effective beam width of an overlapped ultrasonic sensor ring is assessed as the beam width of a single ultrasonic sensor having the same amount of global positional uncertainty, from which a normalized obstacle detection performance index is defined. Second. using the defined index, the design parameters of an overlapped ultrasonic sensor ring are optimized for minimal positional uncertainty in obstacle detection. For a given number of ultrasonic sensors, the optimal radius of an overlapped ultrasonic sensor ring is determined, and for a given radius of an overlapped ultrasonic sensor ring, the optimal number of ultrasonic sensors is determined. Third, the decision rules of positional uncertainty zone for multiple obstacle detection are provided based on the inequality relationships among obstacle distances by three adjacent ultrasonic sensors. Using the provided rules, the obstacle outline detection is performed in a rather complex environment consisting of several obstacles of different shapes.

• Journal of Power System Engineering
• /
• v.16 no.1
• /
• pp.84-90
• /
• 2012

In unmanned vehicles' navigation, the shapes of obstacles are generally irregular and complex. The motion of vehicles based on the range sensor system such as ultrasonic sensors or laser sensors can be unstable due to the irregular shape of the obstacles. In this case, to generate stable trajectory of unmanned vehicles equipped with range sensors, we need an approach that can simplify an obstacle's irregular shape information. In this paper, we propose the trajectory generation algorithm that an vehicle can stably navigate in the environments where irregular shaped obstacles are scattered. The proposed method is verified through the analysis of vehicle's trail and direction data acquired by simulations and implementations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1039-1042
• /
• 2002

SMD(Surface Mounting Device) which mounts electronic components as IC-Chips on PCB automatically, produces a large dynamic force and vibration. The unwanted vibrations in SMD degrade the performance of the precision device and it is the major obstacle to limit its speed for mounting. This study investigated the vibration analysis of a typical SMD to predict the natural frequencies and mode shapes. To validate the finite element analysis of SMD, the FE result was compared with that of ODS measurements. It was shown that the predicted results were well correlated with the experimental modal parameters.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.2
• /
• pp.266-275
• /
• 2009

Variations of individual hip shapes are a major obstacle in pattern making for fitness. The drafting method is used for pattern making in today's apparel industry. Whilst catering to a limited number of information such as waist and hip sizes, this method does not cater to variations in hip shape. This paper describes the analysis of hip shapes using 3D body model and tries to make sure the relationship between hip shape and pattern by calculating hip angle and dart amount. We achieved results in analyzing various hip shapes by extracting hip angle. Moreover, various hip shapes can be divided into three types(A, B and C) by the hip angle value($K_{sh}-K_{wsh}$). When we use computerized draping method to make a personalized pattern for a tigth skirt, we easily create complex dart lines automatically. Therefore we achieve the result of individual dart amount such as distance between dart lines and dart areas. C type of hip shape had short dart length, long distance between dart lines and a large amount of dart area. On the other hand, A type had long dart length, short distance between dart lines and small amount of dart area. B type had long length and long distance between dart lines and large amount of dart area. In traditional pattern making, distance between dart lines is usually proportional to amount of dart area because of similarity in dart line shape. In our pattern, there is no proportional relationship between dart line distance and dart area. This means that variations in hip shapes result in a wide variety of dart line curvature resulting in a wide range of dart area. By ensuring an accurate relationship between hip shape and pattern, it is possible to make patterns which result in clothing that not only fits well, but also exhibits other desirable properties.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.1
• /
• pp.36-41
• /
• 2011

Configuration space(C-space) including configuration obstacle(C-obstacle) is one of the most important concepts in mobile robot path planning. Using C-space and C-obstacles, the robot with different shapes and moving mechanisms can be considered as a point in the C-space. And, as a result, the collision-free path for the robot can be easily achieved. To make C-space including C-obstacle, many researchers used circular approximation method for the efficient caluculation time. This method can help us to save our time by approximating the shape of a robot as the minimum sized circle which can cover all the area of robot. But, by using the circle larger than the robot, more space are considered as the part of robot and, as a result, some obstacles which are very near each other may be considered as a combined one obstacle. To solve this problem, multi-level configuration space is proposed by this paper. This multi-level method also use the circular approximation method as the initial step. But, after finding the initial path, it will check how many obstacles are combined. And then, for each combined obstacle, more accurate C-space generation will be continued. To check the efficiency of the proposed algorithm, time for c-space generation are compared with the well-known accurate C-space generation method using various types of robot shape.