• Journal of Soil and Groundwater Environment
• /
• v.8 no.2
• /
• pp.44-54
• /
• 2003

A kinetic model for evaluating effects of surfactant on the biodegradation of HOC(hazardous organic chemicals) in soil-slurry systems was developed. The model includes the partition of HOC and surfactant, the dissolved-, micellar-, and sorbed-phase biodegradation, the enhanced solubilization of HOC by surfactant addition, and the mass transfer of HOC. Phenanthrene as HOC and Trition X-100, Tergitol NP-10, Igepal CA-720, and Brij 30 were used in the model simulations. The biodegradation rate was increased even with a small micellera-phase bioavailability. The biodegradation was not greatly enhanced due to decreased aqueous HOC concentration by increasing surfactant dose in both cases with and without micellar-phase bioavailability. The effect of sorbed-phase biodegradation on total biodegradation rate was not highly important compared to aqueous- and micellar-phase biodegradation. The model can be applied for surfactant screening and optimal design of surfactant-based soil bioremediation process.

• Journal of Korean Society of Transportation
• /
• v.20 no.6
• /
• pp.31-43
• /
• 2002

Traffic signal control methods are suggested to improve the operational effectiveness of COSMOS system in Seoul. First. a method that improves progression of the corridor traffic flow within a common sub-area was explored. Applying this method, both frequency and magnitude of offset transition were reduced as compared to the existing method. In addition, the level of connection among neighboring corridors increased by applying the method, thus the qualify of progression was also improved. Second, a practical guideline on signal phase design was proposed to improve the efficiency of actuated operations for the left-turn movement. Last, a method for estimating optimal queue length parameters was surveyed and evaluated. An evaluation study was performed for the suggested methods through both field and simulation studies. Results showed that the proposed methods gave better performance than the existing methods. It is expected that the use of proposed methods can improve operational performance of COSMOS.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.10 s.175
• /
• pp.174-185
• /
• 2005

This paper presents the design, fabrication, and testing results of a dual stage actuator system for a fine positioning of magnetic heads in magnetic disk drives. A novel rotary microactuator which is electrostatically driven and utilized as a secondary actuator was designed. The stator and rotor electrodes in the microactuator was revised to have the optimal shapes and hence produces much higher rotational torque compared with the conventional comb-shape electrodes. The microactuators were successfully fabricated using SoG(silicon on glass) processing technology, which is known as being cost-effective. The fabricated microactuator has the structural thickness of $45{\mu}m$ with the gap width of approximately $3{\mu}m$. The dynamic characteristic of microactuator/slider assembly was investigated, and its natural frequency and DC gain were measured to be 3.4kHz and 32nm/V, respectively. The microactuator/slider assembly was integrated into a HDD model V10 of Samsung Electronics Co. and a dual servo algorithm was tested to explore the tracking performance of dual stage actuator system where the LDV signals instead of magnetic head signals were used. Experimental results indicate that this system achieves the tracking accuracy of 30nm. This value corresponds to a track density of 85,000 track per inch(TPI), which is about 3 times greater than that of current hard disk drives.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.996-1001
• /
• 2006

Automatic washing machines have been improved and popularized steadily since the first electric washing machine was produced in the early 1900's. Appliance industry has tried to obtain the performance of washing machine with large capacity, high energy efficiency, low vibration and low noise levels. As the installation peace of a washer becomes closer to the living space, vibration and noise problems become more important challenges. In general, a washing machine has four legs to support its body. Four legs of the washing machine should be attached on a floor. If not so, it may cause severe vibration or walking in the spin-drying process. Unfortunately, the floor of an ordinary house is bumpy in general, and the consumers will not accept bolting washing machines to a foundation; moreover, sometimes they move the location of their washing machines to utility rooms or bath rooms or kitchens and don't care for leveling the legs exactly. In this study, we devise an auto-leg system that prevents the occurrence of abnormal vibration and walking of washing machines. It is simply composed of a spring and a friction damper. Some experiments are implemented to show the dynamic characteristics of the three-dimensional auto-legged washing machine model that is located on the even or uneven ground. A spring parameter is optimized to adjust the length of the auto-leg system automatically up to 10 mm irregularity, and the friction damper is designed to decrease a resonance induced by the spring of the auto-leg system. Some numerical results show that placing the proposed auto-leg system in a washing machine makes good performance with low vibration, as well as low noise, regardless of the unevenness of the floor.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.12
• /
• pp.1322-1328
• /
• 2009

This paper presents vibration analysis of maskless exposure module in printed circuit board(PCB) manufacturing system. In order to complete exposure process in PCB, masking type module has been widely used in electronics industries. However, masking process confronts some limitations of application due to higher production cost for masking as well as lower printing resolution. Therefore, maskless exposure module is started to be in the spotlight for flexible production system to meet the needs of fabrication in variable patterns at low cost. Since maskless exposure process adopts direct patterning to PCB, vibration problems become more critical compared to conventional masking type process. Moreover, movements of exposure engine as well as stage generate vibration sources in the system. Thus, it is imperative to analyze the vibration characteristics for the maskless exposure module to improve the quality and accuracy of PCB. In this study, vibration analysis using the finite element analysis is conducted to identify the critical structural parts deteriorating vibration performance. Also, Experimental investigations are conducted by single/dual encoder measurement process under the operating module speed. Measurement points of vibration are selected by three places, which are base of stage, exposure engine and top of stage, to check the effect of vibration from the exposure engine. Comparisons between analysis results and experimental measurement are conducted to confirm the accuracy of analysis results including the developed FE model. Finally, this studies show feasibility of optimal design using the developed FE analysis model.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.5
• /
• pp.68-79
• /
• 1998

In the years, the concern about high-strength concrete which is new material has been heightened as a result of active research and development. Recently, as the building structure has been being bigger, higher, longer and more specialized, the demand of material with high-strength concrete for building has been increasing. The demand of high -strength concrete is expected to increase with expansion of usage about the complex concrete structures such as bridge structure as well as nuclear plants, underground structures, hydraulic structures and arctic area sturctures. In this research, silica-fume was used as an admixture in order to get a high-strength concrete. Water/binder ration was limited no more than 18 percent and the amount of unit cement was increased. In this study, a number of trial in concrete mix was carried out to get optimal mix design, and the target slump with $10{\pm}2cm$ was set for in-situ construction. High-strength concrete with cylinder strength of 1,200kgf/$cm^2$ in the 28-days was produced and tested. The static test was carried out to measure the ultimate load, the initial load of flexural and diagonal cracking, crack patterns, fracture modes. The load versus strain and load versus deflection relations were obtained form the static test. The test results were compared with the shear strengths predicted by the equations of ACI code 318-89 and orther researchers. Based on the test results, shear strength equation of reinforced concrete beam using high strength concrete was proposed. Form an evaluation of the results of this experimental investigation, it was concluded that shear strength after diagonal tention cracking diminished with the increase in compressive strength for beams.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.12 no.4
• /
• pp.168-180
• /
• 2000

In the Part I, the three dimensional model testing with NNW deep water wave direction gave the results such that the occurrence of breaking waves over the peak of Ear-Do caused very small wave height at the structure position. But the measured wave forces were rather greater than the calculated forces based on deep water wave height. Furthermore, It was also perceived that the time series of the forces looked like corresponding to the case that waves were superimposed by an unidirectional current. In the present Part II, the current is presumed to be a flow secondly induced by breaking waves, and an extensive study to clarify the current in a quantitative sense is performed through numerical analysis and hydraulic experiment. The results showed that a strong circulation can surely occur in the vicinity of the structure due to radiation stress differentials given by the breaking waves. It was also recognized that the velocity of the induced current varied with the magnitude of energy dissipation rate introduced in the numerical analysis. The numerical analysis was tuned adjusting the dissipation rate so that the calculated wave field could closely match with the experimental results of Part I. The fluid force (in prototype) for the optimal match showed approximately 2.2% increased over the calculated value based on the deep water wave height (24.6m) whereas the force corresponding to the average of the experimental values showed the increase of about 13.0%.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.3
• /
• pp.103-112
• /
• 2014

BY the Transformers and reactors, the input electrical energy is converted into magnetic energy. At the end through the magnetic energy was passed at the output parameter. Specially At the flyback transformer or a reactor airgap were designed to contain more magnetic energy. But that work is very difficult for the optimal design. It is that Contradictions are between the length of the Air-gap, Winding inductance, DC bias. As to e Several conflicting conditions in order to determine the optimum Air-gap has a lot of experience and trial & error is necessary. The approach proposed in this paper, the auxiliary winding on the core attached to part of primary core, that by applying a DC voltage has a dramatic effect like Core with designed Air-gap. This inventiveness and advantage is to regulate arbitrarily the Saturation Flux Quantity by the input signal to secondary winding. Accordingly obtained the biggest effect is that increasing limits of the saturation current destined by the material and shape of the conventional core. In other words, that can decreas the size of the transformer and reactor, While maintaining the current saturation capacity. This paper, prove its effect as using the local flux saturation in transformers and reactors for research by the computer program using the finite element method (FEM) simulation, followed by actual experiment to verify

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.575-579
• /
• 2007

Sludge disposal technology has been studied with many researchers since disposal of sewage sludge has been a social problem. The current technologies include incineration, carbonization, pyrolysis, landfilling and fertilization. However, all of these processes require a dry process, because sewage sludge with more than 80% high water content is difficult to be used as a raw material. This study has the purpose to establish the optimal operation conditions and the technology as changing the variables: kiln residence time, sludge load, dryer temperature, by using the previous study that is rotary kiln type dryer designed as a numerical simulation study. As the results, optimum conditions are determined as follows: kiln residence time, sludge load, dryer temperature are $62.5kg/m^3{\cdot}hr$, 26.2 min, $330^{\circ}C$, respectively. Content of water, drying efficiency, weight loss, volume loss show that the results are $10{\pm}2$, 88, 80, 60%, and the dried sludge is released by a dryer below 10 mm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.1969-1975
• /
• 2012

The air brake system used in heavy vehicle is very important from the point of safety due to its weight. In general, air brake system generates relatively long response time and large loss of pressure. It is known that the response time can be decreased by optimal design of brake system, i.e., by increasing the system pressure, minimizing the air line, and material of components. In this study, We developed experimental rigs for the measurement of braking response of heavy duty trucks and compared with the simulated results obtained from the net work fluid flow system analysis code (FLOWMASTER). The effect of several parameters such as, system pressure, diameter of pipe, chamber temperature on the brake response performance have been examined.