• Journal of the Korea Fashion and Costume Design Association
• /
• v.11 no.1
• /
• pp.43-51
• /
• 2009

The cotton, wool, cotton/wool blended(80:20) and tencel fabrics were treated with low temperature oxygen or argon plasma, enzymes(cellulase or protease), or oxygen plasma-enzyme and examined for their weight loss and conditions for treatment for the environment friendly finishing. In the plasma treatment argon gas had better effect on the weight loss than oxygen gas did and the weight loss of all the fabrics was increased as increasing discharge power and discharge time. The weight loss of cotton, wool, cotton/wool blended(80:20) fabrics decreased in a large measure after 1 hr but that of tencel didn't decrease after 1 hr. In case of cellulose fibers oxygen gas plasma induced chemical functional groups on the surface of substrate more than argon gas plasma did so the weight loss of wool was larger than that of cotton, tencel fabrics in oxygen plasma-enzyme treatment. The weight loss of cotton and tencel fabrics decreased the initial stage because oxygen plasma pre-treatment caused cross linking as well as etching effect but argon plasma pre-treatment didn't. The plasma pre-treatment cleared the way for enzyme treatment on the whole but oxygen plasma pre-treatment bear in hand the increase of weight loss more or less because of the cross linking on the surface of cellulose fibers. The appropriate conditions for plasma treatment was 10-1Torr, 40W for 30minutes and for cellulase treatment were enzyme concentration of $3g/{\ell}$, pH 5, $60^{\circ}C$ for 1hr and for protease treatment were enzyme concentration of $4g/{\ell}$ pH 8, $60^{\circ}C$ for 1hr.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1566-1570
• /
• 2013

In this paper, we analyzed the electric characteristics of the OLEDs device of which anode ITO has been treated with the oxygen plasma. We fabricated the basic three-layer structure (ITO / AF / $Alq_3$ / $Cs_2CO_3$ / Al) device, analyzed how the oxygen plasma treatments of the ITO surface affects to the electrical characteristics of OLEDs. We also produced a four-layer structure device (ITO / AF / TPD / $Alq_3$ / $Cs_2CO_3$ / Al) with the oxygen plasma treatment. From the comparative analysis to the devices, we confirmed following results. The three-layer structure OLEDs device with oxygen plasma treatment has better characteristics than the device without the treatments; maximum luminance, luminous efficiency, and external quantum efficiency are improved approximately 151 [%], 126 [%], and 175[%], respectively. Also, the electric characteristics of the four-layer structure device with oxygen plasma treatment are improved comparing to the characteristics of the three-layer structure device with oxygen plasma treatment; maximum luminance, luminous efficiency, and external quantum efficiency are improved approximately 144 [%], 115 [%], and 124[%], respectively.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.3
• /
• pp.376-379
• /
• 2013

Multi-walled carbon nanotubes (MWCNTs) were synthesized using catalytic chemical vapor deposition (CVD) method. Oxygen plasma treatment was applied to modify surface state of the CNTs synthesized for improvement of field emission performance. Surface state of the plasma treated CNTs was studied by X-ray photoelectron spectroscopy (XPS). The surface states of the CNTs were changed as a function of plasma treatment time. The oxygen related carbon shift was moved toward higher binding energy with the plasma treatment time. This result implies that the oxygen plasma treatment changes the surface state effectively. While any shift in carbon 1s peak was not detected for the as grown CNTs, oxygen related carbon shift was detected for the plasma treated CNTs. Carbon shift implies that closed CNT tips were opened by the oxygen plasma and reacted with oxygen species. Since the field emission occurs at pentagons or dangling bonds of the CNT tips, the increase of carbon-oxygen bonds plays an important role in field emission behavior by increasing the number of electron emission sites resulting in improvement of the field emission performance.

• Textile Coloration and Finishing
• /
• v.19 no.1 s.92
• /
• pp.45-52
• /
• 2007

Polyacrylonitrile(PAN) fiber was treated with low-temperature plasmas of argon and oxygen for surface modification, and its surface chemical structure and morphology were examined by a field emission scanning electron microscope(FESEM) and a Fourier-transform infrared microspectroscopy(IMS). The argon-plasma treatment caused the only mechanical effect by sputtering of ion bombardment, whereas the oxygen plasma brought about a chemical effect on the PAN fiber surface. The experimental evidences strongly suggested that cyclization of nitrile group and crosslinking were likely to occur in the oxygen-plasma treatment. On the other hand, with the argon-plasma treatment, numerous my pits resulted in ranging from several tens to hundreds nanometers in radius. The plasma sensitivity of functional groups such as C-H, $C{\equiv}N$, and O-C=O groups in the PAN fiber was dependent on their chemical nature of bonding in the oxygen-plasma, in which the ester group was the most sensitive to the plasma. Vacuum-ultraviolet(VUV) radiation emitted during plasma treatment played no substantial role to alter the surface morphology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.232-233
• /
• 2005

The Surface of semi-conductive silicone rubber was treated by oxygen plasma to improve adhesion and electric performance in joints between insulating and semi-conductive silicone materials. Surface characterizations were assessed using contact angle measurement and Fourier transform infrared spectroscope (FTIR). Adhesion level was understood from T-peel tests between plasma treated semi-conductive and insulating material. Electrical breakdown strength was measured to understand the charge of electrical performance. From the results, the oxygen plasma treatment produces a significant increase in function group of containing oxygen which can be mainly ascribed to the creation of carbonyl groups on the silicone surface from the strength were improved. Therefore it is concluded then plasma treatment leads to decrease voids originating form poor adhesive, and the improve the adhesion in silicone interface. So we could obtain higher electrical design level of silicone material used for electrical apparatus using oxygen plasma treatment.

• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.112-115
• /
• 2015

In this study, the surface of ITO films was modified using $N_2-O_2$ molecular plasma, and the effects of oxygen concentration in the plasma on the ITO surface properties were investigated. Upon plasma treatment of ITO films, the surface roughness of ITO films seldom changed up to the oxygen concentration in the range of 0% to 40%, while the roughness of the films slightly changed at or above the oxygen concentration of 60%. The contact angle of water droplet on ITO films dramatically changed with varying oxygen concentration in the plasma, and the minimum value was found to be at the oxygen concentration of 20%. The plasma resistance at this condition exhibited a maximum value, and the change of resistance showed an inverse relationship compared to that of contact angle. From these results, it was conjectured that the chemical reactions in the sheath of the molecular plasma dominated more than the physical actions due to energetic ion bombardment, and also the plasma resistance could be used as an indirect indicator to qualitatively diagnosis the state of plasma during the plasma treatment.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.6
• /
• pp.261-266
• /
• 2003

We investigated the effect of oxygen plasma treatment of indium-tin oxide(ITO) surface on the performance of electroluminescence(EL) devices. ITO surface treated oxygen plasma has been analyzed using atomic force microscope(AFM) and X-ray photoelectron spectroscopy(XPS), to investigate the relations between the properties of the ITO surface and the properties of the current-voltage-luminance(I-V-L) characteristics of the fabricated OLED with the structure of ITO(plasma treatment) / TPD / Alq$_3$/ Al. It is found that the oxygen plasma treatment of ITO anode improve the hole injection of the OLED due to the modification of the surface states. The treated ITO anode nay be low voltage with high luminance efficiency.

• Textile Coloration and Finishing
• /
• v.23 no.3
• /
• pp.195-200
• /
• 2011

Silicone-coated fabric were treated by oxygen low temperature plasma to improve the adhesion. The surface of silicone-coated fabric was modified with gaseous plasma of several discharge power in the presence of oxygen gas at 1Torr pressure. Oxygen plasma treatment introduces oxygen-containing functional groups and micro-pittings on the silicone-coated fabric surface. The treated fabrics with oxygen low temperature plasma were measured by contact angle analyzer and XPS(X-ray photoelectron spectroscopy), and interfacial adhesion was measured by T-peel test. The surface of fabric was investigated by SEM photographs. The chemical and physical modification of the surface wettabillity by plasma treatment can increase the adhesion.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.134-140
• /
• 2004

Semi-crystalline poly(ethylene terephthalate) (PET) film surfaces were modified with argon and oxygen plasmas by radio-frequency (RF) glow discharge at 240 mTorr/40 W; the changes in topography and surface structure were investigated by atomic force microscopy (AFM) in conjunction with specular reflectance of infrared microspectroscopy (IMS). Under our operating conditions, analysis of the AFM images revealed that longer plasma treatment results in significant ablation on the film surface with increasing roughness, regardless of the kind of plasma used. The basic topographies, however, were different depending upon the kind of gas used. The specular reflectance analysis showed that the ablative mechanisms of the argon and oxygen plasma treatments are entirely different with one another. For the Ar-plasma-treated PET surface, no observable difference in the chemical structure was observed before and after plasma treatment. On the other hand, the oxygen-plasma-treated PET surface displays a significant decrease in the number of aliphatic C-H groups. We conclude that a constant removal of material from the PET surface occurs when using the Ar-plasma, whereas preferential etching of aliphatic C-H groups, with respect to, e.g. , carbonyl and ether groups, occurs upon oxygen plasma.

• Textile Coloration and Finishing
• /
• v.34 no.2
• /
• pp.102-108
• /
• 2022

The physicochemical properties of stainless steel fibers which were modified by oxygen plasma treatment were analyzed through microscopy and XPS analysis. The wettability of the surface of the stainless steel fiber was observed by measuring water contact angle to find out the effect of the plasma treatment time on the surface characteristics of the stainless steel fiber. In addition, in order to understand the effect of oxygen plasma treatment on the deterioration of the stainless steel fiber properties, the physical properties due to plasma treatment was investigated by measuring the weight reduction, tensile strength, elongation, tensile modulus of the stainless steel fibers according to the treatment time. As a result, the stainless steel fiber surface was etched by the oxygen plasma and the surface became more wettable by the introduction of hydrophilic functional groups. However the physical properties of the stainless steel fiber were not significantly deteriorated even if the surface of the stainless steel fiber made hydrophilic.