• Polymer(Korea)
• /
• v.35 no.3
• /
• pp.249-253
• /
• 2011

The effect of morphological development in PET/PEN blending on the physical properties of PET/PEN blend film as a flexible substrate was investigated. The two phase morphology was obtained in PET/PEN blends and it caused the improvement of dimensional stability of PET/PEN blend as a flexible substrate. The two phase morphology and crystallinity of PET/PEN blends could be controlled by the transesterification between PET and PEN during the film processing and this macroscopic structural development affected the dimensional stability of PET/PEN blend films. Better dimensional stability was obtained with increasing crystallinity and decreasing the level of transesterification.

• Polymer(Korea)
• /
• v.35 no.6
• /
• pp.599-604
• /
• 2011

The PET-PEN copolymers have been synthesized and the effect of their morphology on the physical properties of polyester flexible substrate was investigated. It was found that the block sequence of synthesized copolymer was varied depending upon DMT/NDC ratio in polymerization. Higher PET-PEN and PEN block sequence in polyester copolymer resulted in the increase of glass transition temperature and it caused the enhancement of dimensional stability as a polyester flexible substrate. The highest coefficient of thermal expansion(CTE) was obtained when DMT/NDC ratio is 50/50. Synthesized PET-PEN copolymer seems to be acceptable as a flexible substrate since it shows that their optical transmittance at 550 nm is over 80% and thermal weight loss at $280^{\circ}C$ for 1 hr is less than 0.4 wt%.

• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.711-716
• /
• 2013

The effect of chain orientation and relaxation on the characteristics of poly(ethylene naphthalate) (PEN) flexible substrate has been studied. It was found that the coefficient of thermal expansion (CTE) of PEN under $100^{\circ}C$ decreased as low as $20ppm/^{\circ}C$ due to the lowering of chain mobility by chain orientation. The thermal shrinkage was found to appear near glass transition temperature because of chain relaxation. It could be minimized by thermal annealing but CTE increased again up to $70ppm/^{\circ}C$ which was 65% of intrinsic CTE of PEN. Unstrained thermal annealing made possible to avoid the thermal shrinkage with maintaining low CTE obtained by chain orientation. Chain orientation did not affect the optical transmittance; however, thermal annealing caused the decrease of optical transmittance up to 5%. This was understood by the minor crystallization due to the thermal annealing near glass transition temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.287-287
• /
• 2010

We report a new direct patterning method, called liquid bridge-mediated nanotransfer molding (LB-nTM), for the formation of two- or three-dimensional structures with feature sizes between tens of nanometers and tens of micron over large areas. LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. This procedure can be adopted for automated direct printing machines that generate patterns of functional materials with a wide range of feature sizes on diverse substrates. Arrays of TIPS-PEN TFTs were fabricated on 4" polyethersulfone (PES) substrates by LB-nTM using PDMS molds. An inverted staggered structure was employed in the TFT device fabrication. A 150 nm-thick indium-tin oxide (ITO) gate electrode and a 200 nm-thick SiO2dielectric layer were formed on a PES substrate by sputter deposition. An array of TIPS-PEN patterns (thickness: 60 nm) as active channel layers was fabricated on the substrate by LB-nTM. The nominal channel length of the TIPS-PEN TFT was 10 mm, while the channel width was 135 mm. Finally, the source and drain electrodes of 200 nm-thick Ag were defined on the substrate by LB-nTM. The TIPS-PEN TFTs can endure strenuous bending and are also transparent in the visible range, and therefore potentially useful for flexible and invisible electronics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.303.1-303.1
• /
• 2016

Polymer-like amorphous carbon films were deposited on polyethylene naphthalate (PEN) substrate by plasma-enhanced chemical vapor deposition (PECVD) and their water vapor transmission rates (WVTR) were tested. propane was used as precursors. To make a polymer-like amorphous carbon film the deposition rate, surface roughness, light transmittance, and WVTR of the films were characterized as a function of the precursor feed ratio and plasma power. The water vapor transmission rates of bare PEN film and single layer PAC on PEN substrate were 6.95 g/m2/day and 0.3 g/m2/day, respectively. The superior property the water vapor permeability of thin layers of PAC was attributed to uniform coverage and good adhesion between PAC film and PEN substrate.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.657-659
• /
• 2008

Barrier coating properties of PVA/$SiO_2$ on the flexible substrates (PEN) have been investigated. Thin layer of PVA/$SiO_2$ organic-inorganic hybrid materials were deposited on PEN substrate by the spin-coating. The optical properties and surface roughness of barrier layer on flexible substrate were characterized by AFM, UV-Vis and WVTR/ OTR.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.746-749
• /
• 2002

Aluminum oxide thin films were grown on a poly ethylene naphthalate (PEN) substrate at the temperature of 100$^{\circ}C$ using atomic layer deposition method. The film showed very flat morphology and good adhesion to the substrate. The visible spectrum showed higher transmittance in the range from 400 nm to 800 nm than that of PEN. The water vapor transmission value measured with MOCON for 230nm oxide-deposited PEN was 0.62g/$m^2$/day @ 38$^{\circ}C$, while that of PEN substrate was 1.4g/$m^2$/day @ 38$^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.961-968
• /
• 2009

In this work, transparent conductive oxide(TCO) films such as $In_2O_3-SnO_2$(ITO) and $In_2O_3-ZnO$(IZO) were prepared on polyethylene naphthalene(PEN) and glass substrates by using rf-magnetron sputtering system. The TCO films deposited on PEN substrate show very poor conductivity as compared to that of the TCO films deposited on glass substrates. From the results of the residual gas analysis(RGA) test, this poor stability of plastic substrate is presumed to be caused by the deteriorated adhesion between the TCO films and the plastic substrate due to outgassing from the plastic substrate during deposition of TCO films. From our experiment, it is found that the vaporization of some defects in the plastic substrates deteriorate the adhesion of the TCO films to the plastic substrate, because the most plastic substrates containing the water vapor and/or other adsorbed particles such as organic solvents. Mixing of these gases vaporized in the sputtering process will also affect the electrical property of the deposited TCO films. Inorganic thin composite $(SiO_2)_{40}(ZnO)_{60}$ film as a gas barrier layer is coated on the PEN substrate to protecting the diffusion of vapors from the substrate, so that the TCO films with an improved quality can be obtained.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.6
• /
• pp.1095-1100
• /
• 2021

In this study, ITZO thin films were deposited on glass, sapphire, and PEN substrates by RF magnetron sputtering, and their electrical and optical properties were investigated. The resistivity of the ITZO thin film deposited on the glass and sapphire substrates was 3.08×10-4 and 3.21×10-4 Ω-cm, respectively, showing no significant difference, whereas the resistivity of the ITZO thin film deposited on the PEN substrate was 7.36×10-4 Ω-cm, which was a rather large value. Regardless of the type of substrate, there was no significant difference in the average transmittance of the ITZO thin film. Figure of Merits of the ITZO thin film deposited on the glass substrate obtained using the average transmittance in the absorption region of the amorphous silicon thin film solar cell and the absorption region of the P3HT : PCBM organic active layer were 10.52 and 9.28×10-3 Ω-1, respectively, which showed the best values. Through XRD and AFM measurements, it was confirmed that all ITZO thin films exhibited an amorphous structure and had no defects such as pinholes or cracks, regardless of the substrate type.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.396-396
• /
• 2012

$TiO_2$ anatase nanotube arrays (NTAs) were grown by electrochemical anodization and followed annealing of Ti foil. Ethylene glycol/$NH_4F$-based organic electrolyte was used for electrolyte solution and using second anodization process to obtain free-standing NTAs. After obtaining NTAs, ITO film was deposited by sputtering process on bottom of NTAs. UV-curable NOA was used for attach free-standing NTAs on flexible plastic substrate (PEN). Solid state electrolyte (spiro-OMeTAD) was coated via spin-coating method on top of attached NTAs. Ag was deposited as a counter electrode. Under AM 1.5 simulated sunlight, optical characteristics of devices were investigated. In order to use flexible polymer substrate, processes have to be conducted at low temperature. In case of $TiO_2$ nano particles (NPs), however, crystallization of NPs at high temperature above $450^{\circ}C$ is required. Because NTAs were conducted high temperature annealing process before NTAs transfer to PEN, it is favorable for using PEN as flexible substrate. Fabricated flexible solid-state DSSCs make possible the preventing of liquid electrolyte corrosion and leakage, various application.