• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.63-68
• /
• 2009

The power management integrated circuit(PMIC) for CCD image sensor is presented in this study. A CCD image sensor is very sensitive against temperature. The temperature, that is heat, is generally generated by the PMIC with low efficiency. Since the generated heat influences performance of CCD image sensor, it should be minimized by using a PMIC which has a high efficiency. In order to develop the PMIC with high efficiency, the input stage is designed with synchronous type step down DC-DC converter. The operating range of the converter is from 5V to 15V and the converter is controlled using PWM method. The PWM control circuit consists of a saw-tooth generator, a band-gap reference circuit, an error amplifier and a comparator circuit. The saw-tooth generator is designed with 1.2MHz oscillation frequency. The comparator is designed with the two stages OP Amp. And the error amplifier has 40dB DC gain and $77^{\circ}$ phase margin. The output of the step down converter is connected to input stage of the charge pump. The output of the charge pump is connected to input of the LDO which is the output stage of the PMIC. Finally, the PMIC, based on the PWM control circuit and the charge pump and the LDO, has output voltage of 15V, -7.5V, 3.3V and 5V. The PMIC is designed with a 0.35um process.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.39-44
• /
• 2011

This purpose of this study is to propose the characteristics analysis of the PCB pattern designed two modes for the output voltage value on the PMIC through converting the limited voltage value inputted from a battery. The PCB design technology has been undergoing difficulty in getting the related technology in a domestic market because of increasing EMI/EMC, Cross-talk, Impedance. And it requires to have the appropriate clearance between the patterns and the technology of PCB pattern width with a amperage according to various uses. The study carried out the characteristics analysis of the PCB pattern designed from a direct output method without a capacitor[mode1], to an output method through a capacitor[mode2] for PMIC output voltage value. Besides, we calculated the pattern width with a amperage using the equation suggested by IPC-2221, presenting the right way of the layout design to analyze the trouble with the test. Therefore, this study is expected to contribute not only to applying the PMIC design for the mobile panel power supply, but also helping the design and application technology in various areas such as car control, camera, note-book, computer, PDA, etc.

• Journal of IKEEE
• /
• v.13 no.2
• /
• pp.208-215
• /
• 2009

The high efficiency power management IC(PMIC) with DT-CMOS(Dynamic Threshold voltage MOSFET) switching device for portable application is proposed in this paper. Because portable applications need high output voltages and low output voltage, Boost converter and Buck converter are embedded in One-chip. PMIC is controlled with PWM control method in order to have high power efficiency at high current level. DTMOS with low on-resistance is designed to decrease conduction loss. Boost converter and Buck converter, are based on Voltage-mode PWM control circuits and low on-resistance switching device, achieved the high efficiency near 92.1% and 95%, respectively, at 100mA output current. And Step-down DC-DC converter in stand-by mode below 1mA is designed with LDO in order to achive high efficiency.

• Journal of IKEEE
• /
• v.14 no.2
• /
• pp.90-97
• /
• 2010

The high efficiency power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device and DTMOS Error Amplifier is presented in this paper. PMIC is controlled with PWM control method in order to have high power efficiency at high current level. Dynamic Threshold voltage CMOS(DT-CMOS) with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuits consist of a saw-tooth generator, a band-gap reference circuit, an DT-CMOS error amplifier and a comparator circuit as a block. the proposed DT-CMOS Error Amplifier has 72dB DC gain and 83.5deg phase margin. also Error Amplifier that use DTMOS more than CMOS showed power consumption decrease of about 30%. DC-DC converter, based on Voltage-mode PWM control circuits and low on-resistance switching device is achieved the high efficiency near 96% at 100mA output current. And DC-DC converter is designed with Low Drop Out regulator(LDO regulator) in stand-by mode which fewer than 1mA for high efficiency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.1
• /
• pp.149-152
• /
• 2017

This paper investigated the method for the output of power management IC (PMIC) for BLE beacon with energy harvesting device to be maintained constantly. The capacitor was used to store the energy supplied from energy harvesting device such as solar module and the capacitance was estimated to the optimum value according to the interval for the BLE beacon to send advertising signal.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1222-1228
• /
• 2010

This paper presents a design of the CMOS LDO regulator with a fast transient response for a high speed PMIC(power management integrated circuit). Proposed LDO regulator circuit consists of a reference voltage circuit, an error amplifier and a power transistor. 2-stage wide-band OTA buffer between error amplifier and power transistor is added for a good output stability. Although conventional source follower buffer structure is simple, it has a narrow output swing and a low S/N ratio. In this paper, we use a 2-stage wide-band OTA instead of source follower structure for a buffer. From HSPICE simulation results using a $0.5{\mu}m$ CMOS standard technology, simulation results were 16 mV/V line regulation and 0.007 %/mA load regulation.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.2
• /
• pp.357-362
• /
• 2020

The TMFT, a sub-system of TINC, provides voice calls, data transmission and reception, and multimedia services to individual users. At the time of development in 2011, the power circuit of the TMFT was designed to electrical power supply to each device via a charger IC. However, the newly improved power supply circuit allows power to be supplied to each device through the PMIC without configuring the charger IC separately. In this paper, the power circuit design structure of TMFT applied in the development stage and the improved power circuit design structure were compared. And we verified through experiments whether the improved power circuit can be applied to TMFT. The experimental method was verified by directly comparing the current consumption test, charge time comparison test, and rising temperature test during charging each of before and after improvement terminals.

• Journal of Convergence for Information Technology
• /
• v.10 no.8
• /
• pp.47-52
• /
• 2020

In this study, a simulation investigation was conducted on the method of reducing switching noise and spurious emission among design methods for step-down DC-DC converter modules for automotive. A typical 4-layer converter circuit using a PMIC(Power Management Integrated Circuit) chip was presented, and the simulation results of conductive emissions at two input terminals (+, -) and the point between the input filter and the PMIC was performed in the 1.0~5.0MHz band and the 100MHz band. The results for the conducted and radiated emissions in the HF(3~30MHz) and VHF(30-300MHz) bands were presented. It showed an improvement of about 10dB over the bands by routing the output terminal placed on the 3 or 4-layer in the opposite direction to the input terminal. The result of this study is expected to be useful in the design of the DC-DC converter modules in the future because it gives a better improvement compared to the existing methods.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.260-264
• /
• 2016

The MAX77846, which is compatible with MAX77826, is a sub-power management IC (PMIC) for the latest Wearable Watch and 3G/4G smart phones. The MAX77846 contains N-MOSFET (N channel Metal-Oxide Semiconductor Field-Effect Transistor), a high-efficiency regulator, and comparator, etc to power up peripherals. The MAX77846 also provides power on/off control logic for complete flexibility and an $I^2C$ (Inter Integrated Circuit) serial interface to program individual regulator output voltages. In this paper, the simplified power macro-model based on MAX77846 is designed to verify the performance of the battery voltage in terms of current and time, and simulated by using of the LTspice. In addition, it is verified how much time can the charged battery capacity for Samsung Galaxy Gear 2 be used to operate a specified function after measuring the currents flowing to carry out the main functions in real time, which will be applicable to design parameters for the advanced power module

• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.250-255
• /
• 2010

The interleaved power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device is proposed in this paper. The buck-boost converter used to provide the high output voltage and low output voltage for portable applications. Also we used the PWM(Pulse Width Modulation) control method for high power efficiency at high current level. DTMOS with low on-resistance is designed to decrease conduction loss. The interleaved PMIC to reduce output ripple. And step-down DC-DC converter in stand-by mode below 1mA is designed with LDO in order to achive high efficiency.