• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.619-624
• /
• 2023

In this paper, TE(transverse electric) scattering problems by a resistive strip grating between a double dielectric layer are analyzed by using the FGMM(fourier galerkin moment method) known as a numerical method of electromagnetic fileld. The boundary conditions are applied to obtain the unknown field coefficients, the scattered electromagnetic fields are expanded in a series of Floquet mode functions, and the resistive boundary condition is applied to analysis of the resistive strip. In order to deal with the problem of the double dielectric layer, numerical calculation was performed only when the thickness and relative permittivity of the dielectric layers had the same value. Overall, as the resistivity of the uniform resistivity increased, the current density induced in the resistive strip decreased, the reflected power decreased, and the transmitted power relatively increased. The numerical results of the structure proposed in this paper are shown in good agreement compared to the results of PMM, a numerical analysis method of the existing paper.

• Journal of Advanced Navigation Technology
• /
• v.26 no.6
• /
• pp.510-515
• /
• 2022

In this paper, a microstrip patch sensor antenna (MPSA) for detecting the concentration of an ethanol-water solution in a microliter volume is proposed. A rectangular slot was added at the radiating edge of the patch to increase the sensitivity to the relative permittivity change. To improve a low input resistance caused by placing an ethanol-water solution, which is a polar liquid with high dielectric constant and high loss tangent, on the patch, a quarter-wave impedance transformer was added between the 50-ohm feedline and the patch, and the MPSA was fabricated on a 0.76 mm-thick RF-35 substrate. A cylindrical container was made of acryl, and 15 microliters of the ethanol-water solution was tested from 0% to 100% of ethanol concentration at 20% intervals. Experiment results show that the resonant frequency increased from 1.947 GHz to 2.509 GHz when the ethanol concentration of the ethanol-water solution was increased from 0% to 100%, demonstrating the performance as a concentration detecting sensor.

• Korean Journal of Materials Research
• /
• v.12 no.10
• /
• pp.814-819
• /
• 2002

TiN and TaN films as electrode materials of reactive sputtered $Ta_2$$O_{5}$ were prepared by sputtering to compare their thermal stabilities with $Ta_2$$O_{5}$ The microstructural change of $Ta_2$$O_{5}$ films with annealing was also investigated. As- deposited $Ta_2$$O_{5}$ film on $SiO_2$ was amorphous and annealing of 80$0^{\circ}C$ for 30 min made it transform to $\beta$-Ta$_2$O$_{5}$ crystalline which contains amorphous particles with the size of a few nm. Crystallization temperature of Ta$_2$Ta_2$$O_{5}$ on TaN is higher than that on TiN electrode. The interface between TaN and Ta$_2$O$_{5}$ maintained stably even after vacuum annealing up to $800^{\circ}C$ for 1 hr, but TiN interacted with $Ta_2$$_O{5}$ and so interdiffusion between TiN and $Ta_2$$O_{5}$ occurred by vacuum annealing of 80$0^{\circ}C$ for 1 hr. It indicates that TaN is thermally more stable with $Ta_2$$O_{5}$ than TiN.N.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.300-305
• /
• 2012

In this paper, a miniaturized bow-tie monopole UWB antenna with band rejection characteristic is proposed. To miniaturize the proposed antenna, a perfect magnetic wall(PMW) condition is applied to primitive bow-tie monopole antenna. An uneven ground patch, a tapered feeding structure and a edge-chopped main patch are adapted for impedance matching. A quater-lambda slot resonator is inserted at main patch to prevent interference in UWB band from another band. The proposed antenna is fabricated on Taconic RF60-A substrate with relative permittivity of 6.15. The size of the proposed antenna is $30.0{\times}39.7mm^2$, which is only 45 % of the conventional bow-tie monopole antenna. The proposed antenna covers full UWB band with return losses less than -10 dB and has band stop characteristic in 5 GHz WLAN band. The maximum gains are within -1.0~5.0 dBi, the group delay variations are within 1.0 ns and the radiation patterns show directivity characteristics in x-y plane.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.3
• /
• pp.1-8
• /
• 2002

In order to study electric properties of (Pb$\_$0.9/La$\_$0.1/)Ti$\_$0.975/O$_3$(PLT (10)) films with varying excess lead concentration (7.5, 10, 12.5, 15 ㏖% excess lead), the PLT films were deposited by sol-gel process. DTA analyses reveal that the crystallization temperature of the precursor powers decreased with increasing amount of excess lead. XRD patterns of PLT reveal pure perovskite structure and the preferred orientation increased with increasing Pb content in the films. With increasing amount of excess P$\_$b/, the relative permittivity ($\xi$$\_$r/) increased and leakage current density at 100 ㎸/cm transformed 4.01$\times$10$\^$-5/, 2.42$\times$10$\^$-6/, 1.27$\times$10$\^$-6/, 1.56$\times$10$\^$-6/A/㎠ respectively. In the results of hysteresis loops measured at 166 kV/cm, the remanent polarization (P$\_$r/) and the coercive field (E$\_$c) are 6.36$\mu$C/cm and 58.7 ㎸/cm, respectively (at 12.5 ㏖% excess P$\_$b/) With increasing amount of excess Pb, the remanent polarization for PLT thin film degraded to about 44%, 27%, 15%, 16% of the initial value after 10$\^$9/ cycles./TEX>) With increasing amount of excess Pb, the remanent polarization for PLT thin film degraded to about 44%, 27%, 15%, 16% of the initial value after $10^{9}$ cycles.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2005.09a
• /
• pp.201-212
• /
• 2005

[ $Epoxy/BaTiO_3$ ] composite embedded capacitor films (ECFs) were newly designed fur high dielectric constant and low tolerance (less than ${\pm}15\%$) embedded capacitor fabrication for organic substrates. In terms of material formulation, ECFs are composed of specially formulated epoxy resin and latent curing agent, and in terms of coating process, a comma roll coating method is used for uniform film thickness in large area. Dielectric constant of $BaTiO_3\;&\;SrTiO_3$ composite ECF is measured with MIM capacitor at 100 kHz using LCR meter. Dielectric constant of $BaTiO_3$ ECF is bigger than that of $SrTiO_3$ ECF, and it is due to difference of permittivity of $BaTiO_3\;and\;SrTiO_3$ particles. Dielectric constant of $BaTiO_3\;&\;SrTiO_3$ ECF in high frequency range $(0.5\~10GHz)$ is measured using cavity resonance method. In order to estimate dielectric constant, the reflection coefficient is measured with a network analyzer. Dielectric constant is calculated by observing the frequencies of the resonant cavity modes. About both powders, calculated dielectric constants in this frequency range are about 3/4 of the dielectric constants at 1 MHz. This difference is due to the decrease of the dielectric constant of epoxy matrix. For $BaTiO_3$ ECF, there is the dielectric relaxation at $5\~9GHz$. It is due to changing of polarization mode of $BaTiO_3$ powder. In the case of $SrTiO_3$ ECF, there is no relaxation up to 10GHz. Alternative material for embedded capacitor fabrication is $epoxy/BaTiO_3$ composite embedded capacitor paste (ECP). It uses similar materials formulation like ECF and a screen printing method for film coating. The screen printing method has the advantage of forming capacitor partially in desired part. But the screen printing makes surface irregularity during mask peel-off, Surface flatness is significantly improved by adding some additives and by applying pressure during curing. As a result, dielectric layer with improved thickness uniformity is successfully demonstrated. Using $epoxy/BaTiO_3$ composite ECP, dielectric constant of 63 and specific capacitance of 5.1nF/cm2 were achieved.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.2
• /
• pp.85-94
• /
• 1998

Due to relatively high permittivity of water in soils, we placed the soil condenser into soils to measure the soil moisture content. The soil condenser was made with two insulated iron sticks. The capacitance of the soil condenser was determined by the pulse period from RC type oscillation circuit and the highest voltage output accepting 10MHz pulse. After zero point adjustment, the measured relative capacitance percentage (RCS) to the standard condenser obtained by the oscillation circuit almost linearly correlated with the end depth of the sensor submerged in water. The RC type oscillation was disturbed by many sensor installed in a close distance in one place, presumably resulting in that the sensor sticks played as a interfering antennas generating or accepting electron waves from them. The temperature dependance of the output from the sensors could be corrected through experimentally determined revision function. Although lineal correlation was found between soil moisture and RCS, users should derive their own correlation function for every sensor to measure soil moisture, because the outputs were influenced by the installation depth and layout in the soil. The voltage type sensor responded inversely with soil moisture content and so was not suitable to the accurate measurement of soil moisture, but allows high economic benefit in various application such as simplified measurement of soil moisture and irrigation line control because of its low component count. The voltage type moisture sensor could be reinforced by relay controlling circuit to open and to close the solenoid valves respectively at optimal limits of the least and the most soil moisture according to user's adjustment.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.3
• /
• pp.1-11
• /
• 1999

It is now common practice to utilize the quadrature RF coils to improve the signal-to-noise ratio (SNR) in the Magnetic Resonance Imaging (MRI) System. In addition, to make such an available SNR improvement, it is mandatory to use a well-designed quadrature coupler, which facilitates a perfect 3-dB coupling and quadrature-phase shift. However, the four ports matching condition has to be well considered during the RF excitation and the signal detection period. This work investigates the effects of such a mismatching condition (especially, due to patient) from the analysis, simulation, and real implementation and firstly proposes dynamic loading technique for a quadrature coupler and transmitting/receiving switch module to minimize a patient mismatching and enhance a system reliability. Also, we designed and implemented the quadrature coupler and transmitting/receiving switch module using microstrip. As a result, the SNR of our MRI system using the microstrip quadrature coupler and transmitting/receiving switch module with dynamic load increases 3 dB compared with the old one using USA quadrature switch. Also, the power capability of quadrature coupler and transmitting/receiving switch module is 5-kw peak power. Considering power loss and reduction of size, we used a RT/duroid 6010 substrate with high permittivity and for simulation we use Compact Software.

• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.915-920
• /
• 2004

The main phase of $BaTi_{4}O_9$-based ceramics was transformed to $BaTi_{5}O_{11}$ caused by the sintering with borosilicate glass, which was analyzed by using XRD and TEM. We considered that the phase change from $BaTi_{4}O_9$-based ceramics to the Ti-rich $BaTi_{5}O_{11}$ phase resulted from borosilicate glass selective absorbing of Ba ions from the $BaTi_{4}O_9$. In these results, we found a dependence on the amounts of the glass frits and the annealing temperature, and the phase change is also dependent of the main phases of $Ba_{4}Ti_{13}O_{30},\;and\;Ba_{2}Ti_{9}O_{20}$, which are involved in the $BaO-TiO_2-based$ Ti-rich region. In the case of sintering of middle- and high- permittivity material with additional glass frits for middle- and high- dielectric coefficients LTCC composition, control of weight fraction of the glass frits accompanying low-temperature sintering property with appropriate phase change is required.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.534-540
• /
• 2013

Interest of the hand effect on the electromagnetic wave are internationally increasing with the increase of the use of the mobile phone. IEC TC106(International Electrotechnical Commission, Technical Committee 106) promotes international research exchange program in order to reflect the effect of human hands in the standard assessment method of human exposure dosimetry by the electromagnetic wave of mobile phones. Since current commercialized hand phantom is manufactured by taking into account the average size of westerners and provides only one grip posture, it imposes many restrictions on the accurate SAR measurement. Therefore, the development of proper hand phantom accounting for domestic situation and various grip posture capability is essential in order to analyze the accurate effect of human hand on the exposure estimation. In this paper, a jelly hand phantom suitable for Korean was manufactured with various grip posture capability at 835 MHz and 1,800 MHz bands. Although the tolerances of permittivity and conductivity of the manufactured hand phantom are with ${\pm}10%$ each, it was much less than CTIA(Cellular Telecommunication Industry Association) tolerance of ${\pm}20%$ at both bands. Its 3D CAD(3 Dimensional Computer Aided Design) file which was developed can be utilized for the simulation of human hand effect on SAR measurement of mobile phones. The findings in this study can be utilized for the analysis of human hand effect on SAR measurement of a mobile phone.