• Applied Chemistry for Engineering
• /
• v.17 no.1
• /
• pp.28-32
• /
• 2006

This study investigated the variation of flow rates in microchannels that consisted of polydimethyl siloxane (PDMS) and glass using various external voltages. Three different microchannel widths and two different depths. PDMS and negative photoresist (SU-8) were used to make the microchannels by the soft lithographic method. For each depth of microchannel ($50{\mu}m$ and $100{\mu}m$), three different widths ($100{\mu}m$, $200{\mu}m$ and $300{\mu}m$) were made. In each case, several different external voltages were applied (0.3 kV, 0.35 kV, 0.4 kV and 0.45 kV) to examine the flow rates. Our results indicated that flow rate increased with an increase of the external voltage at the same microchannel width. This was because the electrical field was increased as the external voltage increased. For the same external voltage, the flow rate increased as the microchannel's width increased. These results showed that the resistance in the microchannel decreased as the microchannel's width increased. Also, to investigate the effect of microchannel's depth and width, the cross-sectional area of the microchannel was increased to the double in area. As a result, the effect of the microchannel's depth was higher at a low external voltage, and the effect of the microchannel's width was higher at a high external voltage.

• Applied Chemistry for Engineering
• /
• v.24 no.6
• /
• pp.593-598
• /
• 2013

In this study, we have evaluated the water absorption phenomenon of photoresist dry film, which is commonly used to build circuits on PCB (Printed Circuit Board) by photolithography, by using ATR-FTIR (Attenuated Total Reflectance-Fourier Transform Infrared). We have firstly observed significant change in fracture mode of dry film with respect to temperature and humidity, which we assumed the material transition from ductile to brittle. Secondly, we have established the process of absorption test for determining the diffusion coefficients of water into the dry film both with gravimeter and ATR-FTIR. We have successfully calculated the diffusion coefficients for each environmental conditions from the results which we achieved by gravimeter and ATR-FTIR. Compared to the gravimeter which is a conventional method for absorption test, the ATR-FTIR method in this study has been found to be very easy to use and have the same accuracy as gravimeter. Moreover, we are expecting to use the ATR-FTIR as an appropriate method to study the absorption phenomena related to any kinds of solvent and polymer system.

• Korean Journal of Materials Research
• /
• v.19 no.3
• /
• pp.132-136
• /
• 2009

This study investigates GaAs dry etching in capacitively coupled $BCl_3/N_2$ plasma at a low vacuum pressure (>100 mTorr). The applied etch process parameters were a RIE chuck power ranging from $100{\sim}200W$ on the electrodes and a $N_2$ composition ranging from $0{\sim}100%$ in $BCl_3/N_2$ plasma mixtures. After the etch process, the etch rates, RMS roughness and etch selectivity of the GaAs over a photoresist was investigated. Surface profilometry and field emission-scanning electron microscopy were used to analyze the etch characteristics of the GaAs substrate. It was found that the highest etch rate of GaAs was $0.4{\mu}m/min$ at a 20 % $N_2$ composition in $BCl_3/N_2$ (i.e., 16 sccm $BCl_3/4$ sccm $N_2$). It was also noted that the etch rate of GaAs was $0.22{\mu}m/min$ at 20 sccm $BCl_3$ (100 % $BCl_3$). Therefore, there was a clear catalytic effect of $N_2$ during the $BCl_3/N_2$ plasma etching process. The RMS roughness of GaAs after etching was very low (${\sim}3nm$) when the percentage of $N_2$ was 20 %. However, the surface roughness became rougher with higher percentages of $N_2$.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.421-426
• /
• 2009

We report on the capacitively coupled O2 plasma etching of PMMA and polycarbonate (PC) with a diffusion pump. Plasma process variables were process pressure and CCP power at 5 sccm $O_2$ gas flow rate. Characterization was done in order to analyze etch rate, etch selectivity, surface roughness, and morphology using stylus surface profilometry and scanning electron microscopy. Self bias decreased with increase of process pressure in the range of 25$\sim$180 mTorr. We found an important result for optimum pressure for the highest etch rate of PMMA and PC, which was 60 mTorr. PMMA and PC had etch rates of 0.46 and 0.28 ${\mu}m$/min under pressure conditions, respectively. More specifically, etch rates of the materials increased when the pressure changed from 25 mTorr to 60 mTorr. However, they reduced when the pressure increased further after 60 mTorr. RMS roughnesses of the etched surfaces were in the range of 2.2$\sim$2.9 nm. Etch selectivity of PMMA to a photoresist was $\sim$1.5:1 and that of PC was $\sim$0.9:1. Etch rate constant was about 0.04 ${\mu}m$/minW and 0.02 ${\mu}m$/minW for PMMA and PC, respectively, with the CCP power change at 5 sccm $O_2$ and 40 mTorr process pressure. PC had more erosion on the etched sidewall than PMMA did. The OES data showed that the intensity of the oxygen atomic peak (777.196 nm) proportionally increased with the CCP power.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.640-644
• /
• 2014

As a process of plat panel display production, slot coating is widely used for the coating of photoresist on a wide glass substrate. A uniform coating thickness is important, and the coating uniformity is divided into nozzle and machine directions. The machine and nozzle directions coating uniformities are influenced by the operation condition of coater and flow uniformity inside the die, respectively. Non-uniform coating during steady coating process occurs according to those factors, however, non-uniform coating along the machine and nozzle directions has been observed at the beginning of coating by unsteady flow. In this study, steady and unsteady state flow simulations have been performed and compared with experiment to examine the causes of non-uniform coating. Computational results exhibited that it took a time to get a uniform pressure distribution at whole inside the die, and during this period of time edge regions showed lower exit velocity compared with center region. Subsequently edge regions had thinner coated layers than center region. However edge regions showed higher exit velocity than center region after steady state, and this made edge regions had thicker coated layer than center region.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.148-152
• /
• 2007

The prototype of color fitters for the liquid crystal displays (LCD) using cholesteric liquid crystal monomers was produced. Cholesteric liquid crystal is characterized by the unique optical features of selective reflection, which is due to the helical twisting structures of LCs comparable to the wavelength of the incident light under certain conditions of substrate treatment. In the results of the experiment, cholesteric films for red, green, and blue light reflections respectively were produced and the viewing angle dependence of these films were investigated. Reflective light of red and green films shifted to shorter wavelength regions as viewing angle becomes greater, but blue one shifted very little. Periodic micrometer-sized half-spherical photoresist formed by thermal reflow method after photo-lithography was patterned on glass substrates. The viewing angle dependence of reflective light colors of red, green, and blue films on the patterned substrates compared with those on no patterned substrates was investigated. We could confirm the dependences were much smaller on the patterned substrates by bare eyes and Lab-color coordination methods qualitatively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.221-221
• /
• 2013

Vertical LED (VLED) has been recognized as a way to obtain the high-power LED due to their advantages [1]. However, approximately 4% of the light generated from the active region is extracted, if the light extraction from side walls and back side is neglected because of Fresnel reflection (FR) and total internal reflection (TIR) [2,3]. In this study, the optical simulation of the VLED with the various microstructures was performed. Among them, the microlens having the diameter of 3 ${\mu}m$ and the height of 1.5 ${\mu}m$ shown the best result was chosen, and then, optimized microlens was formed on a GaN template using conventional semiconductor process. Various microstructures were proposed to improve the light extraction efficiency (LEE) of the VLED for the simulation. The LEE was simulated using LightTools based on a Monte Carlo ray tracing. The microstructures with hemisphere, cone, truncated and cylinder pattern having diameter of 3 ${\mu}m$ were employed on the top layer of the VLED respectively. The improvement of the LEE by using the microstructure is 87% for the hemisphere, 77% for the cone, 53% for the truncated, 21% for the cylinder, compared with the LEE of the flat surface at the reflectance of 85%. The LEE was increased by 88% at the height of 1.5 ${\mu}m$, compared with the LEE of the flat surface. We found that the microlens on the top layer is the most suitable for increasing the LEE. In order to apply the proposed microlens on n-GaN surface, we fabricated microlens on a GaN template. A photoresist array having hexagonal-closed packed microlens was fabricated on the GaN template. Then, optimization of etching the GaN template was performed using a dry etching process with ICP-RIE. The dry etching carried out using a gas mixture of Cl2 and Ar, each having a flow rate of 16 sccm and 10 sccm, respectively with RF power of 50 W, ICP power of 900 W and chamber pressure of 2 mTorr was the optimum etching condition as shown in Fig. 2(a).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.3-3
• /
• 2003

고밀도 플라즈마를 생산할 수 있는 대면적용 플라즈마 소스의 개발은 미세전자구조 산업에서부터 FPD 산업에 이르기까지 많은 영역에 걸쳐 필수 불가결한 기술요소가 되어가고 있 다. 이러한 대면적용 고밀도 플라즈마에의 적용을 위하여 새로운 유도결합형 플라즈마 소오스의 개발이 진행되고 있으며, 차세대 반도체 식각 및 세정 공정을 위하여 여러 형태의 안 테나가 연구되어지고 있다. 그러나 TFT -LCD에 적용이 가능하게끔 기존의 ICP 소오스를 직 접적으로 대면적화 하는 데에는 여러 가지 문제점들로 인해 그 한계점이 들어났다. 그 예로 안테나의 길이가 길어짐에 따른 안테나 저항 값이 커지며, 안테나 소스 길이자체가 사용하는 인가전력(13.56MHz)의 반파장에 해당되는 길이가 되었을 경우 생기는 심각한 정상파 효과, 유전물질의 두께 증가 및 그에 따른 재료비의 상승 및 관리상의 어려움들이 바로 그것 이라 할 수 있겠다. 그러므로, 본 연구에서는 차세대 TFT -LCD 대면적 공정에 적용 가능한 고밀도 플라즈마 를 발생시키기 위해서 내장형 유도결합형 선혈 안테나를 사용하였다. 내장형 유도결합형 선 혈 안테나가 가지고 있는 고유의 정전기적 결합효과를 최소화시키기 위해 직사각형모앙의 플라즈마 댐버(830mm*1,020mm)에서 영구자석을 사용하여 multi-cusp 자장효과 및 다양 한 자장의 배열에 따른 플라즈마 특성변화를 살펴보았다. 영구자석을 사용하여 외부자장을 인가하였을 때가, 그럴지 않은 때보다 RF 안테나 코일의 전압을 낮춰주었으며, 영구자석의 배열에 따라 코일의 인덕턴스의 값이 크게 변함을 알 수 있었다. 그리고 최적화된 자장의 배열은 플라즈마의 이온밀도를 증가시켰으며, 플라즈마의 균일도도 10% 이내로 유지됨을 알 수 있었다. 또한 영구자석에 의한 자장의 유무 및 공정압력과 인가전력에 따른 P Photoresist Film의 식각특성에 관해 살펴보았다.증을 위한 실험.측정장비의 구입 및 업계와의 공동활용, 국내.외 최신기술 정보자료의 수집과 신속제공, 국내.외 전문가 초청 활 용, 미래 지향적 목적활용 기초연구사업 수행, 미래기술 동향예측 및 홍보 등을 통해 서 국내 도금기술의 기술자립 및 고도화를 위한 여건마련을 위하여 노력하고 있다.빛 이때의 부식속도(선형분극법), 인위적인 피막 파괴 전,후 의 전위 변화 및 부식속도 측정법에 의한 국부부식 발달 저지능 등을 평가하여 각 실험결과를 비교분석하여 보았다. 수록 민감하여 304 의 IGSCC 와 매우 유사한 거동을 보인다. 본 강연에서는 304 와 600 의 고온 물에서 일어나는 IGSCC 민감도에 미치는 환경, 예민화처리, 합금원소의 영향을 고찰하고 이에 대한 최근의 연구 동향과 방식 방법을 다룬다.다.의 목적과 지식)보다 미학적 경험에 주는 영향이 큰 것으로 나타났으며, 모든 사람들에게 비슷한 미학적 경험을 발생시키는 것 이 밝혀졌다. 다시 말하면 모든 사람들은 그들의 문화적인 국적과 사회적 인 직업의 차이, 목적의 차이, 또한 환경의 의미의 차이에 상관없이 아름다 운 경관(High-beauty landscape)을 주거지나 나들이 장소로서 선호했으며, 아름답다고 평가했다. 반면에, 사람들이 갖고 있는 문화의 차이, 직업의 차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$순응$\lrcorner$과 $\ulcorner$표현$\lrcorner$

• Resources Recycling
• /
• v.22 no.4
• /
• pp.81-90
• /
• 2013

Since the 1990s, the rapid development of information and communication industry, the demand for semiconductor and LCD continues to increase. Therefore in the formation of fine circuit patterns, which are the cores of sensitizer and the most expensive thinner and stripper liquor used to remove photoresist and its dilution, the amount in demand are dramatically increasing, emerging need for recycling of waste thinner and stripper liquor. Recently, recycling technologies of stripping process waste solution has been widely studied by economic aspects and environmental aspects, in terms of efficiency of the stripping process. In this study, analyzed paper and patent for recycling technologies of waste solution from stripping process. The range of search was limited in the open patents of USA (US), European Union (EP), Japan (JP), Korea (KR) and SCI journals from 1981 to 2010. Patents and journals were collected using key-words searching and filtered by filtering criteria. The trends of the patents and journals was analyzed by the years, countries, companies, and technologies.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.7
• /
• pp.33-39
• /
• 2015

In this work, SU-8 passivated IZO thin-film transistors(TFTs) made by solution-processes was investigated for enhancing stability of indium zinc oxide(IZO) TFT. A very viscous negative photoresist SU-8, which has high mechanical and chemical stability, was deposited by spin coating and patterned on top of TFT by photo lithography. To investigate the enhanced electrical performances by using SU-8 passivation layer, the TFT devices were analyzed by X-ray phtoelectron spectroscopy(XPS) and Fourier transform infrared spectroscopy(FTIR). The TFTs with SU-8 passivation layer show good electrical characterestics, such as ${\mu}_{FE}=6.43cm^2/V{\cdot}s$, $V_{th}=7.1V$, $I_{on/off}=10^6$, SS=0.88V/dec, and especially 3.6V of ${\Delta}V_{th}$ under positive bias stress (PBS) for 3600s. On the other hand, without SU-8 passivation, ${\Delta}V_{th}$ was 7.7V. XPS and FTIR analyses results showed that SU-8 passivation layer prevents the oxygen desorption/adsorption processes significantly, and this feature makes the effectiveness of SU-8 passivation layer for PBS.