• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.95-100
• /
• 1998

A helical inductively coupled plasma asher, which produces low energy and high density plasma, has been built and investigated for photoresist stripping process. Oxygen ion density in the order of $10^{11}/cm^3$ is measured by Langmuir probe, and higher oxygen radical density is observed by Optical Emission Spectrometer. As RF source power is increased, the plasma density and thus photoresist stripping rate are increased. Independent RF bias power to the wafer stage provides a dc bias to the wafer and an ability to add the ion assisted reaction. At 1 KW of the source power, the coupling mechanism of the RF power to the plasma is changed from the inductive mode to the capacitive one at about 1 Torr. This change causes the plasma density and ashing rate decreases abruptly. The critical pressure of the mode change becomes larger with larger RF power.

• Clean Technology
• /
• v.24 no.3
• /
• pp.175-182
• /
• 2018

In this research, we investigated the cleanliness by optimizing the water content of the aqueous stripper in fluidic strip process. The stripping properties of the photoresist with optimized aqueous stripper were compared with the commercial organic stripper. The stripping performance was evaluated by electrical and optical characteristics on the surface of the transparent electrode that compare with stripped the transparent electrode surface and the rare surface before patterning by the photoresist. As a result of the photoresist stripping process of the organic stripper and the aqueous stripper optimized for water content, the aqueous stripper exhibited better electrical and optical characteristics than the organic stripper. In the case of the fluidic strip process with organic stripper, the photoresist dissolves in the stripper solution during stripping which can cause re-adsorption by contamination. Whereas that the aqueous stripper under development seems to decrease the photoresist dissolution in the stripper solution. Because the cyclodextrin contained in the stripper captures organic photoresist into hall of cyclodextrin which stripped through swelling and tearing. The photoresist residue captured by the cyclodextrin can be filtered. After the fluidic stripping process by different chemical stripping mechanism, the cleanliness of the organic stripper and aqueous stripper was compared and analyzed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.11
• /
• pp.1143-1148
• /
• 2004

In this study, photoresist stripping in semiconductor or LCD (liquid crystal display) fabrication processes using DIO, was investigated. In order to obtain the high PR stripping efficiency of DIO. we have developed new ozone-generating system with high ozone concentration and ozone-resolving system with high contact ratio. In this study, we obtained ozone gas concentrations of 11 % by new ozone-generating system, ozone-resolving efficiency of 99.5 % and maximum solubility of 130 ppm in deionized water. We applied the newly designed equipments to photoresist stripping processes and obtained similar results to SPM(sulfuric-peroxide mixture) process characteristics.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.1
• /
• pp.73-78
• /
• 1987

The physical mechanism of a RF discharge used in photoresist stripping and etching process are not well understood and, plasma reactor design and the determination of optimum operating coditions are done largely on empirical basis. We analyzed the discharge process through the measurement of plasma characteristics and applied out results tothe analysis of the photoresist stripping. We investigated the effects of plasma electron density, neutral oxygen gas pressure and electrode temperature on the stripping rates and related their effects with the characteristics of plasma.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.387-394
• /
• 2013

As the feature size of integrated circuits continues to decrease, the challenge of achieving an oxidation-free exposed layer after photoresist (PR) stripping is becoming a critical issue for semiconductor device fabrication. In this article, the hydrogen plasma characteristics in direct plasma and the PR stripping rate in remote plasma were studied using a $120{\Phi}$ cylindrical inductively coupled plasma source. E mode, H mode and E-H mode transitions were observed, which were defined by matching the $V_{rms}$ and total impedance. In addition, the dependence of the E-H mode transition on pressure was examined and the corresponding plasma instability regions were identified. The plasma density and electron temperature increased gradually under the same process conditions. In contrast, the PR stripping rate decreased with increasing proportion of $H_2$ gas in mixed $H_2/N_2$ plasma. The decrease in concentration of reactive radicals for the removal of PR with increasing $H_2$ gas flow rate suggests that NH radicals have a dominant effect as the main volatile product.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.1
• /
• pp.14-20
• /
• 2016

This paper describes a green stripping process to effectively strip the remaining DFR layer on a non-alkali-based ITO glass surface after an etching process. A stripper, water-soluble amine compound, is used to investigate the characteristics of stripping ability and to suggest a valid method for the green process. Increasing the composition (5-30% concentration) of the ethanol amine-based stripper was found to greatly reduce the stripping time applied in the dipping method. The composition (30%) achieved an excellent stripping effect and free-residue impurities. Additionally, it was possible to obtain the effect of stripping in a way to sustain the release before generating DFR sludge from the ITO glass surface by using dipping condition (stripping time) in the composition. An Additional stripping process (buffering) out of dipping can realize productivity improvement and cost reduction because of the higher proportion of re-use of the stripping solution used in the DFR removal step.

• Clean Technology
• /
• v.15 no.2
• /
• pp.69-74
• /
• 2009

A high-dose ion-implanted photoresist (HDIPR) was stripped off from the surface of a semiconductor wafer by using a mixture of supercritical carbon dioxide and a co-solvent. The additional ultrasonication improved the stripping efficiency remarkably and thus reduced the stripping time by supplying physical force to the substrate. We investigated the effect of co-solvents, co-solvent concentration, and stripping temperature and pressure on the stripping efficiency. The wafer surfaces before and after stripping were analyzed by scanning electron microscopy and by an energy dispersive X-ray spectrometer. The HDIPR could be stripped off completely in 3 min with 10%(w/w) acetone/sc$C0_2$ mixture at 27.6 MPa and 343 K.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.4
• /
• pp.281-289
• /
• 2016

Agitation is a secondary process used to increase the PR stripping force on an ITO-glass surface; it is an efficient approach to stripping during production. It activates the stripper to chemically penetrate the PR layer and assists by breaking down the physical bonding forces at the surface. In this study, different stripping tests were conducted by varying the dipping time, the composition, the strip temperature, and the stripper concentration. Optimal PR strip conditions were estimated by using comparative visual inspection of stripped sample surfaces. The stripping process was affected by changes in the moving speeds and the sample positions. It was confirmed that the stripping capability improved at a dilute stripper ratio of 20-40% and a strip temperature of $30-40^{\circ}C$ and within 60 s of strip time.

• Electrical & Electronic Materials
• /
• v.9 no.9
• /
• pp.918-924
• /
• 1996

A downstream oxygen plasma is generated by capacitively coupled RF power and applied to photoresist stripping. Stripping rate (ashing rate) is measured in terms of RF power, chamber pressure, oxygen flow rate and temperature. Ashing reaction is thermally activated and depends on oxygen radical density. The ashing process is optimized to have the high ashing rate, good uniformity and minimal plasma damage using a statistical method.

• 연구논문집
• /
• s.33
• /
• pp.99-109
• /
• 2003

Recently the utilization of the ozone dissolved de-ionized water(DIW-$O_3$) in semiconductor wet cleaning process and photoresist stripping process to replace the conventional sulfuric acid and hydro peroxide mixture(SPM) method has been studied. In this paper, we propose the water-electrode type ozone generator which has the characteristics of the high concentration and purity to produce the high concentration DIW-$O_3$ for the photoresist strip process in the semiconductor fabrication. The proposed ozone generator has the dual dielectric tube structure of silent discharge type and the water is both used to electrode and cooling water. Through this study, we obtained the results of the 10.3 wt% of ozone gas concentration at the oxygen gas of 0.5 [liter/min.] and the DIW-$O_3$ concentration of 79.5 ppm.. Through the photoresist stripping test using the produced DIW-$O_3$, we confirmed that the photoresist coated on the silicon wafer was removed effectively in the 12 minutes.