• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.12
• /
• pp.705-712
• /
• 2003

In this paper, we propose new unified methodologies of reliability and its cost evaluation in power distribution systems. The unified method means that the proposed reliability approaches consider both conventional evaluation factor, i.e. sustained interruptions and additional ones, i.e. momentary interruptions and voltage sags. Because the three voltage quality phenomena generally originate from the outages on distribution systems, the basic and additional reliability indices are summarized considering the fault clearing mechanism. The proposed unified method is divided into the reliability evaluation for calculating the reliability indices and reliability cost evaluation for assessing the damage of customer. The analytic and probabilistic methodologies are presented for each unified reliability and its cost evaluation. The time sequential Monte Carlo technique is used for the probabilistic method. The proposed DVL(Demand Varying Load) model is added to the reliability cost evaluation substituting the average load model. The proposed methods are tested using the modified RBTS(Roy Billinton Test System) form and historical reliability data of KEPCO(Korea Electric Power Corporation) system. The daily load profile of the each customer type in domestic are gathered for the DVL model. Through the case studies, it is verified that the proposed methods can be effectively applied to the distribution systems for more detail reliability assessment than conventional approaches.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.9
• /
• pp.1523-1529
• /
• 2010

This paper describes the distribution power system econimical PQMS(Power quality monitoring system) of Utility. Recently, the korea power quality standard has been established based on the IEC Std. By IEC Std., the power quality assessment point is measured in PCC(Point of common coupling). In this case, the utility has to construct PQM system in all customer PCC point and the PQ meter cost would be very high in order to acquire the suitable data. Also the distribution system would be encounter the communication overload problem due to the huge data. Accordingly the utilities could not apply to PQM system in the distribution power system by the cost and communication problem. In this paper, the proposed economical PQMS has the voltage and current signal reiteration function and FFT operation function is transferred the server. Also the voltage and current measurement channels are minimized by a classified substation construction.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.418-419
• /
• 2011

Recently, the korea power quality standard has been established based on the IEC Std. By IEC Std., the power quality assessment point is measured in PCC. In this case, the utility has to construct PQM system in all customer PCC point and the PQ meter cost would be very high in order to acquire the suitable data. Accordingly the utilities could not apply to PQM system in the distribution power system by the cost and communication problem. In this paper, the proposed economical PQMS(Power quality monitoring system) of Utility.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1015-1024
• /
• 2015

This paper introduces a low cost, high efficiency, high performance three-phase unified power quality conditioner (UPQC) by using four-switch three-phase inverters (FSTPIs) and an extra capacitor in the shunt active power filter (APF) side of the UPQC. In the proposed UPQC, both shunt and series APFs are developed by using FSTPIs so that the number of switching devices is reduced from twelve to eight devices. In addition, by inserting an additional capacitor in series with the shunt APF, the DC-link voltage in the proposed UPQC can also be greatly reduced. As a result, the system cost and power loss of the proposed UPQC is significantly minimized thanks to the use of a smaller number of power switches with a lower rating voltage without degrading the compensation performance of the UPQC. Design of passive components for the proposed UPQC to achieve a good performance is presented in detail. In addition, comparisons on power loss, overall system efficiency, compensation performance between the proposed UPQC and the traditional one are also determined in this paper. Simulation and experimental studies are performed to verify the validity of the proposed topology.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.1
• /
• pp.35-44
• /
• 2017

In this paper, we attempt to investigate the moderating effect of brand power on the effect of in-flight service quality on customer satisfaction and recommendation in the aviation industry. The results were as follows. First, in the case of high brand power FSC(full service carriers), the cost-to-benefit ratio as well as all other flight service properties influence to customer satisfaction. However, in the case of low brand power FSC, the cost-to-benefit ratio showed a greater impact of customer satisfaction compared to other in-flight services. Second, as in the case of customer satisfaction, while the cost-to-benefit ratio more influence to customer recommendation than other in-flight services in low brand power FSC, the cost-to-benefit ratio as well as all other flight service properties influence to customer recommendation together in high brand power FSC. Therefore, low brand power FSC required tit-for-tat strategy against to LCC(low cost carriers) by pursuing disruptive innovation for price. And high brand power FSC required sustaining innovation strategy through improving flight services.

• Korean Journal of Materials Research
• /
• v.25 no.9
• /
• pp.487-491
• /
• 2015

In photovoltaic power generation where minority carrier generation via light absorption is competing against minority carrier recombination, the substrate thickness and material quality are interdependent, and appropriate combination of the two variables is important in obtaining the maximum output power generation. Medici, a two-dimensional semiconductor device simulation tool, is used to investigate the interdependency in relation to the maximum power output in front-lit Si solar cells. Qualitatively, the results indicate that a high quality substrate must be thick and that a low quality substrate must be thin in order to achieve the maximum power generation in the respective materials. The dividing point is $70{\mu}m/5{\times}10^{-6}sec$. That is, for materials with a minority carrier recombination lifetime longer than $5{\times}10^{-6}sec$, the substrate must be thicker than $70{\mu}m$, while for materials with a lifetime shorter than $5{\times}10^{-6}sec$, the substrate must be thinner than $70{\mu}m$. In substrate fabrication, the thinner the wafer, the lower the cost of material, but the higher the cost of wafer fabrication. Thus, the optimum thickness/lifetime combinations are defined in this study along with the substrate cost considerations as part of the factors to be considered in material selection.

• Journal of Korean Society for Quality Management
• /
• v.45 no.4
• /
• pp.917-932
• /
• 2017

Purpose: This study aims to identify the most important quality construct among system quality, information quality, and service quality, which are integrated as the second-order construct; perceived quality, and to investigate the relationship between perceived quality, learner satisfaction, learner enjoyment, switching cost, and learner loyalty. Method: Data were collected from learners who had taken e-learning course, and the analysis was conducted in two phases. The first phase described demographic characteristics using SPSS23.0; the second phase involved the second order CFA of perceived quality and the analysis of measurement model and structural model through AMOS 23.0. Results: (1) The explanatory power of system quality, information quality, and service quality appears to be almost equal; (2) Perceived quality positively influences only both learner satisfaction and switching cost; (3) Only learner satisfaction positively influences learner loyalty and switching cost negatively influences learner loyalty. Conclusion: Learner enjoyment does not play an important role in this study, which could be extrapolated in regard to the characteristics of sample. The respondents are over high school students, who emphasize on the acquisition of knowledge rather than enjoyment. Additionally, the result implies that respondents show low loyalty in the high switching cost.

• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.257-264
• /
• 2007

Active power filters can be cost-effective for use in practical systems with the insertion of a few passive elements in shunt or series configuration. The resulting hybrid filters can be designed to provide dominant lower order harmonic elimination and reactive power support by the passive elements so that the burden on the active filter counterpart is reduced. In this paper, the rate reduction in the shunt active filter is estimated when it is connected in parallel with suitable passive tuned harmonic filters. The active filtering system is based on an appropriate control scheme. The simulation and the experimental results of the shunt active filter, along with the estimated value of reduction in rating, show that the hybrid shunt filtering system is quite effective in compensating for the harmonics and reactive power, in addition to being cost-effective.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.4
• /
• pp.374-381
• /
• 2005

The ability to provide quality power has become a significant issue in power systems. The main causes of poor power quality are harmonic currents, poor power factor, supply-voltage variations, etc. A technique of achieving both active current distortion compensation, power factor correction and also mitigating the supply-voltage variation (sag or swell) at the load side is presented in this paper. The operation and rating issues of the proposed Single-phase Unified Power Quality Conditioner are also highlighted. To reduce the total cost while simultaneously increasing the performance, the system is fully digitally controlled using the fixed-point TMS320F240 digital signal processor. The performances of the UPQC, which is composed by shunt and series PWM controlled-converters, have been verified on a laboratory prototype.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.1
• /
• pp.9-16
• /
• 2003

In this paper, we propose a reliability evaluation method considering the momentary interruptions of power distribution systems. The results of research are concentrated on two parts. One is the analytic and probabilistic reliability evaluation of power distribution system considering the momentary interruptions and the other is the reliability cost evaluation that unifies the cost of sustained and momentary interruptions. This proposed reliability cost evaluation methodology is also divided into the analytic and probabilistic approach and the time sequential Monte Carlo method is used for the probabilistic method. The proposed methods are tested using the modified RBTS (Roy Billinton Test System) form and historical reliability data of KEPCO (Korea Electric Power Corporation) system. Through the case studies, it is verified that the proposed reliability evaluation and its cost/worth assessment methodologies can be applied to the actual reliability studies.