• IEMEK Journal of Embedded Systems and Applications
• /
• v.18 no.2
• /
• pp.75-80
• /
• 2023

Unmanned drone stations for automatic charging have been developed in order to overcome the flying time limitation of rotary wing drones. Since the drone stations is an unmanned operating system, each of the drones will be required to have a high degree of landing accuracy. Drone precision landing has been mainly studied depended on image processing technologies, but the image processing systems make several problems, such as the mission weight, the drone cost, and the development complexity increases, and the flight time decrease. Thus, this paper researched accuracy of precision landing based on RTK (real time kinetics) for rotary wing drones. For the experiments of RTK based precision landing, a drone repeatedly performed three missions. The survey accuracies of the RTK about missions respectively were set as 0.3, 0.2, and 0.1 meters. Each mission has one take-off point, two way-points and one landing-point, and was repeated ten times. The experiment results revealed landing error distance means of around 0.258, 0.12 and 0.057 meters on each of RTK setting.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.377-382
• /
• 2006

Precision approach and landing of aircraft in a remote landing zone autonomously present several challenges. Firstly, the exact location, orientation and elevation of the landing zone are not always known; secondly, the accuracy of the navigation solution is not always sufficient for this type of precision maneuver if there is no DGPS availability within close proximity. This paper explores an alternative approach for estimating the navigation parameters of the aircraft to the landing area using only time-differenced GPS carrier phase measurement and range measurements from a vision system. Distinct ground landmarks are marked before the landing zone. The positions of these landmarks are extracted from the vision system then the ranges relative to these locations are used as measurements for the extended Kalman filter (EKF) in addition to the precise time-differenced GPS carrier phase measurements. The performance of this navigation algorithm is demonstrated using simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1433-1434
• /
• 2011

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.1
• /
• pp.54-60
• /
• 2009

In this paper, a precision landing approach is implemented based on real-time image processing. A full-scale landmark for automatic landing is used. canny edge detection method is applied to identify the outside quadrilateral while circular hough transform is used for the recognition of inside circle. Position information on the ground landmark is uplinked to the unmanned helicopter via ground control computer in real time so that the unmanned helicopter control the air vehicle for accurate landing approach. Ground test and a couple of flight tests for autonomous landing approach show that the image processing and automatic landing operation system have good performance for the landing approach phase at the altitude of $20m{\sim}1m$ above ground level.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.77-84
• /
• 2013

Most research on the inkjet printing technology has focused on the development of inkjet head itself, and of process, not on the landing accuracy of the droplets to a target. Thus, this paper presents the modeling and experimental verification on the static landing accuracy and precision of the droplets from the magnetostrictive inkjet head. A simple model based on the angle deviation of a nozzle tip and on a distance to a substrate is considered, assuming that there is no ambient effect. The angle deviation of the nozzle tip is determined by using its digital image with the aid of a pixel calculation program, and the distance to the substrate is set to 1 mm. Three experiments have planned and preformed. The first experiment is to collect the initial data for the landing distribution of the droplets. The second experiment is to collect the repeatability data of the stage used. Then, these data are used to rederive the equation for the final landing position of the droplet. The final experiment is to verify the equation and to show the calibration results. The respective landing accuracy of the droplet after calibration on the x-axis and on y axis has improved from $338.51{\mu}m$ and $-133.63{\mu}m$ to $7.06{\mu}m$ and $13.11{\mu}m$. The respective percent improvement on the x-axis and on y axis reaches about 98 and about 90. The respective landing precision of the droplet after calibration on the x-axis and on y axis has improved from ${\pm}182.6{\mu}m$ and ${\pm}182.88{\mu}m$ to ${\pm}24.64{\mu}m$ and ${\pm}42.76{\mu}m$. The respective percent improvement on the x-axis and on y axis reaches about 87 and about 77.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.1
• /
• pp.19-26
• /
• 2010

To expand the application area of global navigation satellite systems, precision landing is one of the most critical area to be solved. For the development and validation of the precision landing system, many aspects need to be analyzed including the system architecture, signal characteristics, atmospheric delay, communication delay, accuracy, integrity, and availability. Among them, the signal characteristics analysis requires the processing of measurements collected by real-flight experiments. This paper presents the processing results of the real measurements collected by a flight and landing experiment. To process and analyze the data, double differencing position-domain hatch filter is utilized. Accuracy of the proposed filter is evaluated utilizing reference trajectory generated by commercial software. Finally, by comparing with conventional range domain characteristics of position domain filter is analyzed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.5
• /
• pp.788-797
• /
• 2011

This paper analyzes the accuracy on the approach and landing of aircraft to an airport through comparison with airbase Precision Approach Radar and aircraft track data of DGPS equipped in aircraft. The proposed analysis result could be a basis for verifying the possibility that DGPS can be utilized in Airbase precision approach and landing. Position identification capability of widely used commercial DGPS is fairly accurate on latitude and longitude, while there is a slight error for being used in an airbase accurate approach and landing of Category I precision when it comes to altitude. Thus, we tested accuracy by analyzing actual flight track data of high performance aircraft to verify the accuracy of the airbase approach and landing using DGPS. Through the research, we developed instrumentation to compare PAR track data with DGPS track data, which can be used in reducing the number of PAR verification Flight utilizing it as a system measuring PAR accuracy at PAR installation phase.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2003.06a
• /
• pp.3-8
• /
• 2003

A Simulation S/W is developed to evaluate performances of MLS (Microwave Landing System) and IBLS(Integrated Beacon Landing System) in precision auto-landing. For this study classical PID and optimal LQG controllers are developed as well as mathematical models of MLS and IBLS. Ship-landing condition is also considered by assuming sinusoidal movement of the ship in the pitch direction. The simulated aircraft is F-16 in the study of precision auto-landing. For the integrated simulation environment GUI windows are designed for input of parameter values necessary for simulation, such as vehicle performance and environmental data. For validation and verification of models various comparison graphs of simulation outputs are comprised in the GUI design as well as 3D visual simulation of vehicle dynamics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.643-644
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.871-872
• /
• 2012