• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.16-23
• /
• 2013

It is important that proving ground damage is correlated with target customer usage. This paper describes the test mode for durability test of active suspension control system for proving ground correlation and optimization. Acceleration, strain, wheel force and other types of data are collected on a vehicle as it traverses different proving ground surfaces. The primary objective of the analysis is to determine which mixture of proving ground surfaces offers the best representation of customer usage while minimizing the total test time. And durability testing offers the best way to assess the capability of a product to reach its reliability target. The test should be representative of the real environmental load and replicate the same customer usage.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.195-202
• /
• 2002

By using modeling and simulation. today's design engineers are simultaneously reducing time to market and decreasing the cost of development, while increasing the quality and reliability of their products. A driving simulator is the best example of this method and allows virtual designs of control systems, electronic systems, mechanical systems and hydraulic system of a vehicle to be evaluated before costly prototyping. The objective of this Paper is to develop the virtual Proving: ground using a driving simulator and to show its capabilities of an automotive system development tool. For this purpose, including a real-time vehicle dynamics analysis system, the PC-based driving simulator and the virtual proving ground are developed by using VR(Virtual Reality) techniques. Also ABS HIL(Hardware-In-the-Loop ) simulation is performed successfully.

• Journal of Korea Spatial Information System Society
• /
• v.11 no.1
• /
• pp.169-176
• /
• 2009

Korean Land Spatialization Program(KLSP) is the R&D program of the National GIS Project for developing ubiquitous GIS core technologies under control of Ministry of Land, Transport and Maritime Affairs(MLTM). The first program of KLSP, from 2006 to 2012, initiated with $132 million (US dollars) of national fund and $42 million of matching fund. KLPS which aims 'Innovation of the GIS technology for the ubiquitous Korean land' consists of 5 core research projects and 1 research coordination project to practically utilize and commercialize the results of core research. Korean Land Spatialization Group(KLSG) is planning the KLSP proving ground for testing, integrating, exhibiting the KLSP's outcomes. In the near future, this proving ground would be utilized as a national ubiquitous GIS proving ground. The key objective of this paper is to present the conceptual designs and basic plans. In addition, this paper discusses characteristics of the outcomes which are applied to KLSP proving ground.

• Journal of Advanced Navigation Technology
• /
• v.24 no.3
• /
• pp.224-231
• /
• 2020

An optical tracking plays an important role for measurement operation, as it is responsible for low altitude measurements that are difficult to obtain with radar systems. Since the existing optical tracking systems have not been developed in the proving ground itself so far, it is difficult to modify them to fit the environment of the proving ground. Also, they are designed as a vehicle-mounted type, so there is a limitation in selecting an optimal site. The in-house developed small optical tracking system is designed with a simple configuration to overcome these shortcomings and makes it possible for operators to operate the system at any place in the proving ground. In addition, there has been a need of developing small optical trackers by ourselves to be prepared for future research so that artificial intelligence (AI) can be applied to the optical tracking systems. In this paper, we described the design concept of the small optical tracker, the configuration of the components to implement the basic tracking function, and showed the results of the simulation to set the configuration of the equipment according to the characteristics of the flight targets.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.225-231
• /
• 2016

A military vehicle is driven at different usage modes with the army application and servicing conditions. For practical durability validation, DT(Development Test) on a new military vehicle should be run up to the durability target kilometers on test courses in the specified proving ground. Driving velocities with test courses at the endurance mode of DT are established definitely. However, OT(Operational Test) and initial endurance test of production car can't be performed only in the DT courses due to the development period limit. Therefore, this paper focuses on the method to analyze the relative road damages between the endurance test in DT and other endurance test. Road load acquisition tests on KLTV(Korean Light Tactical Vehicle) were implemented at 15 driving modes in off-road and cross-country courses of two tests. Wheel accelerations were processed through band-pass filter, and then the main frequency and maximum power of the signals were computed by PSD analysis. Finally, using the proving ground optimization based on RDS(Relative Damage Spectrum) characterization, the damage factors between off-roads of test courses were determined.

• Corrosion Science and Technology
• /
• v.16 no.6
• /
• pp.298-304
• /
• 2017

Coil spring steels from the automobile suspension part after field exposure for 10 years and those after anti-corrosion validation test in proving ground of 5,000 ~ 10,000 km were examined for corrosion damages. Partial loss of paint, accumulation of corrosion product, and cracking of paint and superficial material were observed. The surface and subsurface region of spring steels had compressive residual stress and high hardness by shot peening. The surface hardness values of the specimens were 620 ~ 670 Hv. They were 60 ~ 80 Hv higher than those of the samples taken from the middle part of the spring. The maximum compressive stress was -916 ~ -1208 MPa measured at depth of about $100{\mu}m$. Electrochemical impedance spectroscopy showed that the resistances of charge transfer and the paint layer of the spring steels ranged from several tens to millions ${\Omega}{\cdot}cm^2$. The resistance of the field samples was much higher than that of the proving ground samples used in this study, implying that the proving ground test condition would be more corrosive than the field environment.

• Journal of Mechanical Science and Technology
• /
• v.17 no.7
• /
• pp.958-965
• /
• 2003

Structural integrity of either a passenger car or a light truck is one of the basic requirements for a full vehicle engineering and development program. The results of the vehicle product performance are measured in terms of ride and handling, durability, noise/vibration/harshness (NVH), crashworthiness and occupant safety. The level of performance of a vehicle directly affects the marketability, profitability and, most importantly, the future of the automobile manufacturer In this study, we used the virtual proving ground (VPG) approach for obtaining the dynamic characteristics. The VPG approach uses a nonlinear dynamic finite element code (LS-DYNA3D) which expands the application boundary outside the classic linear static assumptions. The VPG approach also uses realistic boundary conditions of tire/road surface interactions. To verify the predicted dynamic results, a single lane change test has been performed. The prediction results were compared with the experimental results, and the feasibility of the integrated CAE analysis methodology was verified.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.8 s.113
• /
• pp.806-813
• /
• 2006

An important factor of vibration test using MAST(multi axial simulation table) system is the reliance of input excitation source. Generally the generation of input excitation source is obtained by the measured data on special road in proving ground. The measured data on special road have more exciting energy than the data of real fields, therefore the time and expense for test can be reduced. But the magnitude of input excitation source must be defined by comparison with the excited energy on real field. The object of this paper makes the data base of domestic roads for the definition of input excitation source which is obtained by the measured data on special road in proving ground. These real field data on domestic roads are analyzed by the power spectral density and interrelationship index.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.297-302
• /
• 2007

Vibrating test of vehicle component can be possible in lab-based simulators instead of field testing owing to the development of technology in control algorithm as well as computational process. Currently, Multi-Axial Simulation Table(MAST) is recommended as a vibrating equipment, which excites a target component for 3-directional translation and rotation motion simultaneously and hence, vibrational condition can be fully approximated to that of real road test. But, the vibration-free performance of target component is not guaranteed with MAST system, which is only simulator subjective to the operator. Rather, the reliability of multi-axial vibration test is dependent on the quality of input profile which should cover the required severity of vibrating condition on target component. In this paper, multi-axial vibration testing methodology of vehicle component is presented here, from data acquisition of vehicle accelerations to the obtaining the input profile of MAST using severe data at proving ground. To compare the severity of vibration condition, between real road test and proving ground one, energy principle of equivalent damage is proposed to calculate energy matrices of acceleration data and then, it is determined the optimal combination of special events on proving ground which is equivalent to real road test at the aspects of vibration fatigue using sequential searching optimal algorithm. To explain the vibration methodology clearly, seat and door component of vehicle are selected as a example.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.51-52
• /
• 2007