• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.63-68
• /
• 2005

The nano-grained Pd or Pt-doped $SnO_{2}$ thin films were deposited on the alumina substrate at ambient temperature or $300^{\circ}C$ by using an R.F. magnetron sputtering system and then annealed at $650^{\cir}C$ for 1 hour or 4 hours in air. The crystallinity and microstructure of the annealed films were analyzed. A grain size of the thin films was 30 nm to 50 nm. As a result of gas sensitivity measurements to an alcohol vapor of $36^{\circ}C$, the 2 wt.% Pt-doped $SnO_{2}$ thin-film sensor deposited at $300^{\circ}C$ and annealed at $650^{\circ}C$ for 4 hours showed the highest sensitivity.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.840-845
• /
• 2002

As an ozone gas sensor, the semiconductor gas sensor which is cheap, portable and simple in use and has a high sensitivity and an excellent selectivity, has been known as an alternative. In the present study, ITO ($In_2O_3 95%,\;SnO_2$ 5%) thin films were deposited on the alumina substrate by using R.F. magnetron sputtering method. The substrate temperature was 300$^{\circ}C$ and 500$^{\circ}C$, respectively and then some specimens were annealed at 500$^{\circ}C$ for 4h in air. ITO gas-sensing films formed crystallines before and after annealing. As results of gas sensitivity measurements to an ozone gas, the sensor deposited at 300$^{\circ}C$ and then annealed has the highest sensitivity (sensible below 1 ppm). As the operating temperature increased gradually, the sensitivity decreased but the response time and stability improved.

• Journal of the Korean Ceramic Society
• /
• v.39 no.4
• /
• pp.394-400
• /
• 2002

Tin oxide thin films doped with silicon as anodes for lithium secondary battery were fabricated by R. F. magnetron sputtering technique. The electrochemical results for lithium secondary battery anodes showed that addition of silicon decreases the oxidic state of tin, and, hence, reduced the irreversible capacity during the first discharge/charge cycle. The (110),(101),(211) planes were grown with increasing substrate temperatures. The reversible capacity of thin films fabricated in conditions of $300^{\circ}C$ substrate temperature and 7:3 $Ar:O_2$ ratio was 700 mAh/g.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.6
• /
• pp.398-404
• /
• 2000

The Ti-Al-V-N films have been deposited on various substrates by d.c and r.f reactive magnetron sputtering from a Ti-6Al-4V alloy target in mixed $Ar-N_2$ discharges. The films were investigated by means of XRD, AES, SEM/EDX, microhardness, TG and scratch test. The XRD and SEM results indicated that the films were of single B1 NaCl phase having dense columnar structure with the (111) preferred orientation. The composition of Ti-Al-V-N film was the Ti-7.1Al-4.3V-N(wt%) films. Adhesion and microhardness of Ti-Al-V-N films deposited by r.f magnetron sputtering method were better than those deposited by d.c magnetron sputtering method. The anti-oxidation properties of Ti-Al-V-N films were also superior to that of Ti-N film deposited by the same deposition conditions.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.269-274
• /
• 2003

The electrical, optical and structural properties of ZnNiO thin _ films deposited on Si substrates using rf-magnetron sputtering method have been investigated before and after the thermal annealing processes. The crystallinity of the ZnNiO thin film become degraded with increasing the Ni contents. This is mainly because the lattice of the thin film was expanded due to the oxygen-deficient conditions. Concerning the electrical properties of the thin film, the carrier concentration increases ($6.81\times10^{14}\textrm{cm}^{-2}$) and Hall mobility decreases (36.3 $\textrm{cm}^2$/Vㆍs) with higher doping concentration of Ni. However, the carrier concentration and Hall mobility became low ($1.10\times10^{14}\textrm{cm}^2$ and high (209.6 $\textrm{cm}^2$/Vㆍs), respectively, after the thermal annealing process at $1000 ^{\circ}C$. We also observed a strong luminescene center peaking at 546 nm in photoluminescence spectra, which was caused by a deep level center in the ZnO band gap with oxygen deficient ZnNiO structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.149-149
• /
• 2011

CdS films were deposited on glass substrates by R.F. magnetron sputtering method and the films were annealed at various substrate temperatures ranging from room temperature to $300^{\circ}C$. Structural properties of the films were studied by X-ray diffraction analysis. The structural parameters as crystallite size have been evaluated. The crystallite sizes were found to increase, and the X-ray diffraction patterns were seen to sharpen by increasing substrate temperatures. X-ray diffraction patterns of these films indicated that they contain both cubic (zincblende) and hexagonal (wurtzite) structures as a mixture. Optical properties of the films were measured at room temperature by using UV/VIS spectrometer in the wavelength range of 190 to 1100nm and optical absorption coefficients were calculated using these data. The energy gap of the films was found to decrease, and the band edge sharpness of the optical absorption was seen to oscillate by annealing. The results show that heat treatments under optimal annealing condition can provide significant improvements in the properties of CdS thin films.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.52 no.3
• /
• pp.107-112
• /
• 2003

Amorphous carbon nitride thin films have been deposited on silicon (100) by reactive magnetron sputtering method. The basic depositon parameters varied were the r.f. power(up to 250 W), the deposition pressure in the reactor(up to 100 mtorr) and Ar:$N_2$ gas ratio. FT-IR and X-ray photoelectron spectra showed the presence of different carbon-nitrogen bonds in the films. The surface topography of the films was studied by scanning electron microscopy(SEM) and atomic force microscopy(AFM).

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.51-61
• /
• 1999

$SrBi_2Ta_2O_9$ thin films were prepared on $Pt/SiO_2$/Si p-tyPp (100) substrate by r.f. magnetron sputtering method. The films were annealed at $800^{\circ}C$ and characterized in terms of micro-structures and electrical properties depending on film deposition conditions. XRD patterns of SBT films annealed at $800^{\circ}C$ indicated the typical SBT phase of (006), (111), and (200) with BiPt additional peaks. SEM images show that crystal gram become to grow with increasing the substrate temperature and decreasing the gas pressure. The remanant polarization(2Pr) and the coercive field(Ec) of 200nm thickness SBT film which was deposited at 10$0^{\circ}C$ under 50mtorr gas pressure and annealed at $800^{\circ}C$ were 20.07$\mu$C/$\textrm {cm}^2$ and 79kV/cm, respectively.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2172-2174
• /
• 2005

MgO has been used as the material of the protecting layer for AC PDP. AC PDP is influenced by characteristics of the surface glow discharge on the MgO thin film. Because MgO thin film is practically discharge electrodes, the discharge characteristics of MgO thin film should be varied with the method of deposition. In this study, changing order and time of deposition, we use electron beam evaporation system and R.F reactive magnetron sputtering system in the MgO deposition. Particularly, after using electron beam evaporation system, we use R.F. reactive magnetron sputtering system in the MgO deposition, then we could get lower amount of charge and higher luminance efficiency than only using electron beam evaporation system.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.170-170
• /
• 2005