• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.10a
• /
• pp.158-162
• /
• 1996

A split shaft device is commonly used to measure the radial force of lip seals. The radial force measured with this device includes some inevitable error. This error is caused by the fact that the split shafts cannot maintain a perfect circle when the interference becomes larger or smaller than some initial interference. In this study, a theoretical model for the calculation of the radial contact force has been carried out, and an explicit equation for the measurement error as a function of the initial interference and the interference to be measured has been obtained. The error when the interference is small is not dependent upon the material properties and the shape of the lip seal, but rather upon the amplitude of the initial interference and the interference to be measured. When the interference is larger or smaller than the initial interference, the measured contact force is always underestimated or overestimated.

• Tribology and Lubricants
• /
• v.14 no.3
• /
• pp.94-99
• /
• 1998

Generally not only the radial load but also the moment may be applied to the ball bearings for a shaft system. However it has been difficult to determine the static equivalent load because there is the radial static equivalent equation only for the axial and radial force on the bearings. In this paper, the same static equivalent radial load which makes the maximum contact force at the interface between the ball and groove as the applied radial force and moment generate is calculated under the condition that the radial force and the moment are applied to the bearings simultaneously. The relation between the static equivalent load and applied force is studied. Therefore the simple and effective equation for the static equivalent radial load of the radial load and moment is proposed for the deep groove ball bearings.

• Journal of applied mathematics & informatics
• /
• v.39 no.1_2
• /
• pp.31-43
• /
• 2021

A homogeneous circular disk undergoing a contact force is considered to investigate the thermo-elastic characteristics, and the inquiry is based on the variations of outer surface temperature and angular velocity. The intensity of stresses grows with the increase of outer surface temperature, and the circumferential strain reacts more sensitively to the change of outer surface temperature than the radial strain. In general, higher angular velocity produces; (i) larger expansion in the radial direction, (ii) smaller displacement in the circumferential, (iii) diminished intensity in the stresses. It is demonstrated that outer surface temperature and angular velocity are critical factors in the determination of thermo-elastic characteristics of homogeneous circular disks subjecting to a contact force. The results obtained can be applied on the design of a homogeneous circular cutter to promote proper and reliable thermos-elastic characteristics in service by the proper operation of these parameters.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.4
• /
• pp.787-793
• /
• 2002

In this study, a bar impact test of low velocity was carried out to gain an insight into the damage mechanism and sequence induced in alumina plates(AD 85 and AD 90) under impact conditions. An experimental setup utilizing an instrumented long bar impact was devised, that can measure directly the impact force applied to the specimen and supply a compressive contact pressure to the specimen. During the bar impact testing, the influences of the contact pressure applied along the impact direction to the specimen on the fracture behavior were investigated. The measured impact force profiles explained well the damage behavior induced in alumina plates. The higher contact pressure to the specimen led to the less damage due to the suppression of radial cracks due to the increase in the apparent flexural stiffness of plate. It had produced the change of damage pattern developed in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates. The observed results showed the following sequence in damage developed: The development of cone crack at impact region, the formation of radial cracks from the rear surface of plate depending on the plate thickness, the occurrence of crushing within the cone envelope and the fragmentation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.480-480
• /
• 2008

Vacuum circuit breaker(VCB) is now emerging as an alternative of gas circuit breaker(GCB) which uses SF6 gas as insulating material whose dielectric strength is outstanding. But we have to reduce SF6 gas because SF6 gas is one of greenhouse gas and efforts to reduce greenhouse gas are now trend of the world. Therefore, we can say VCB is the optimal alternative of GCB because vacuum is environmentally friendly. The vacuum interrupter is the core part of VCB to interrupt arcing current. There are mainly two methods to extinguish arc. One is radial magnetic field (RMF) method and the other is axial magnetic field (AMF) method. We deals with RMF method in this paper. Compared with AMP, RMF arc quenching method has different principle to extinguish arc. In case of RMF method, pinch effect is much larger than AMF method. Because of pinch effect RMF type contact electrodes have the single large spot which is severly damaged and melted while AMF type contact electrodes have small and multiple spots which are slightly damaged and melted. To prevent contact electrode being damaged and melted from high temperature-arc, RMF method uses Lorentz force to move arc. In this paper we calculated and compared the arc driving force of two cases and we analyzed the force acting on each part of arc by means of commercial finite element method software Maxwell 3D. They have 3petals and we considered two cases. One is the case when fixed(upper) and movable(lower) contacts are in mirror arrangement (Case 1). The other is the case when one of two contacts (movable contact) is revolved at maximum angle as possible as it can be (Case 2). And at each case above, we analyzed arc driving force at two positions, position 1 is the closest to the center of contact and position 2 is near the edge of petal on fixed contact. As a result we could find that Case 2 generated stronger arc driving force than Case 1 at position 1. But at position 2 Case 1 generated stronger arc driving force than Case 2. This simulation method can contribute to optimizing spiral-type electrode designs in a view of arc driving force.

• Tribology and Lubricants
• /
• v.12 no.4
• /
• pp.13-17
• /
• 1996

립실의 중요 설계 변수인 접촉력의 측정에는 스플릿트축장치가 흔히 사용된다. 축과 립실의 간섭량은 두 개 스플릿트축의 간격으로서 조절된다. 두 축을 초기 위치로부터 측정하고자 하는 임의 위치로 이동시킬 때 정확한 원을 이루지 못해 측정되는 접촉력은 오차를 포함되게 된다. 본 연구에서는 작은 간섭량 범위 내에서 접촉력을 이론적으로 예측할 수 있는 수식을 유도하고 측정 오차 값을 예측하였다. 측정된 립실의 접촉력은 측정 간섭량이 초기간섭량과 일치하는 경우 외에는 항상 오차를 포함하고 있음을 밝혔다. 이 오차는 작은 간섭량 범위 내에서 립실의 재료 특성이나 형상에 무관하며, 10% 이내의 측정 오차 유지를 위해서는 측정 간섭량이 초기 간섭량의 68%에서 187% 범위 내에 들어야 함을 확인하였다.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.848-853
• /
• 2001

A study about the shrink fits of rotor and retaining ring in generator was performed for the cases of three radial interference. The shrink-fitted retaining ring used to restrain the end turns of the winded coils in the rotor against centrifugal force requires very careful attention during design and manufacture because it has traditionally been the highest-stressed component of the generator. The contact pressures and residual stresses were obtained by the finite element analysis for each radial interference at zero, 100% rated, and 120% rated speeds, respectively. The results of analysis show that the radial interference in use needs to be increased carefully.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.376-381
• /
• 2004

A rig was constructed to test the performance characteristics and compare the hydraulic forces exerted on a centrifugal type artificial heart impeller. A conventional shaft. seal and bearing system. while driven by a small electric motor. supported the impeller which was separated from the pump casing by a six degree of freedom force transducer (JR3 Ine). Radial (x. y) and axial (z) hydraulic forces were recorded and compared. At physiological operating conditions. the results indicate that the double entry/exit centrifugal pump encounters a smaller radial force and significantly reduced axial thrust. These experimental results are valuable in the design of a magnetic bearing system to suspend the impeller of a centrifugal artificial heart pump. This experimental technique may also be applied to evaluate the required capacity and predict the lifetime of contact bearings in marine pumps.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.561-566
• /
• 2001

A long bar impact test to alumina plates(AD 85 and AD 90) was carried out by using fabricated impact testing apparatus. The apparatus adopting a long bar of 2.1m in length made it possible to measure directly the applied impact force to the specimen during bar impact. The dimension of specimens was $33{\times}33mm$ and thickness was 3.4mm. Confinement of D2=18mm outer diameter and D1=10.5mm inner diameter was used to provide contact pressure to the specimen. Contact pressure of p=100 or 200MPa was applied to specimen before impact test. Damage caused in those cases were compared with the case of without contact pressure. The damage of specimen was different depending upon the pressure level of confinement. The existence of confinement had suppressed the development of radial cracks from the bottom of specimen and reduced the extent of damage as compared with cases without contact pressure(p=0MPa). Because the application of contact pressure to the specimen increased the apparent flexural stiffness of specimen during bar impact, it had produced the change of developed damage in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.3
• /
• pp.21-26
• /
• 2011

Nonlinear seal friction in pneumatic cylinders can impede the performance of pneumatic systems designed for high precision positioning with favorable high speed actuation. The behaviour of an elastomeric piston seals in high speed pneumatic cylinders is analyzed by nonlinear finite element analysis using ABAQUS. The contact pressures, stress and strain distributions and frictional forces of the squeeze type piston seal are simulated with variation of the seal radial installed interference, the operating pressures, friction coefficients and piston rod velocities. The nonlinear finite element model of the squeeze type piston seal is used to predict deformation of a seal, friction force and contact pressure distributions.