• 한국생산제조학회지
• /
• 제5권4호
• /
• pp.121-128
• /
• 1996

In order to examine spindle deformation characteristics that affects the performance of dynmic cutting acuracy due to tool weight variation in a experimental spindle. thermal deformation value of operrative spindle by the axial displacement and the radial run out was measured according to the rise of spindle temperature through the laps of operation time and the change of rotational speed under the tool weight variation. A qualitative summary is as follows ; 1) The results show that the tool weight affcets the spindle temperature variation in a experimental spindle. 2) Radial run out and axial displacement was measured according to the rise of the spindle temperature and the performance of dynamic cutting accuracy was affected by the tool weight variation. 3) Axial displacement is 1.3 times larger than the radial run out in a experimental spindle conditions. 4) Axial displacement is continuously elongated when the tool weight is repeatly exchanged since the spindle themal deformaion, however, when the same tool weight is used. the displacement is still constant.

• 한국공작기계학회논문집
• /
• 제16권2호
• /
• pp.84-91
• /
• 2007

The radial error motion of a machine tool cutter/spindle system is critical to the dimensional accuracy of the parts to be machined. This paper presents an investigation into spindle run-out effects on cutting mark and surface roughness. We experimented the effects of spindle run-out on surface roughness in flat-end milling by cutting AL 7075 workpiece in various cutting conditions. In order to analyze the effects of run-out on the surface roughness, the spindle's radial error motions was measured by mounting a sphere target onto the spindle as a reference. From the experimental results, it was found that spindle un-out makes a directive effects on surface roughness in flat-end milling.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.149-156
• /
• 1995

This paper presents the surface profile of machined workpiece in face milling operation. The roughness model of feed direction is considered the cutting condition, the profile and run-out of inserts. For the dynamic model the cutting system can be modeled as avibratory system. The dynamic model of surface roughness is considered the relative displacements between tool and work- piece which can be obtained from the cutting system. These model can predict various surface roughnesses. i.e. maximum and arithmetic mean surface ruughnesses. Therefore, the developed model can be used for the monitoring of surface roughness.

• 한국정밀공학회지
• /
• 제23권4호
• /
• pp.29-36
• /
• 2006

Micro drilling by high-speed air bearing spindle is very useful manufacturing technology in electronic industry For the design of high speed air bearing spindle, there are considered stability of air bearing spindle, allowable load of air bearing, run out and tooling system design for micro drill's attach and remove. According to suggested details, we designed and manufactured high-speed air bearing spindle and carried out performance estimation such as run out, temperature change in running air bearing spindle, stiffness, chucking torque. Results are follows; Run out was measured under $5{\mu}m$ at air bearing spindle revolution $20,000\sim125,000rpm$. High speed air bearing spindle's temperature rose about $20^{\circ}C$ after 5 minutes from running and then was fixed. Allowable thrust load of spindle was 17kgf. Chucking torque of collet was 15kgfcm.

• 대한기계학회논문집A
• /
• 제20권8호
• /
• pp.2508-2515
• /
• 1996

Determination of an optimal feed rate is valuable in the sense of the precision and efficient machining. In this regard, a new surface roughness model for the face milling operation that considered the radial and axal runouts of the inserts in the cutter body was developed. The validity of the model was proved through the cutting experiments, and the model is able to predict the real machined surface roughness exactly with the information of the insert runouts and the cutting conditions. From the estimated surface roughness value, the maximum feed rate that obtains a maximum naterial removal rate under the given surface roughness constraint can be selected by using a bisection method. Therefore, this mehod for optimizing the feed rate can be well applied to the using a bisection method. Therefore, this method for optimizing the feed rate can be well applied to the using selsction of the cutting condition during the NC data generation in CAM.

• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.108-116
• /
• 2014

Considering the run-out effect and cutting force coefficients, the cutting force profile of half immersion end-milling was analyzed in detail. The effects of three specific cutting-force coefficients and three edge-force coefficients are verified. Through a detailed investigation, it is proved that the radial cutting force coefficients and are the major factors which increase the cutting forces Fx and Fy in end-milling. However, the axial cutting force coefficients have no influence on the force Fx and Fy changes in end-milling. Also, the analyzed end-milling force model shows good consistency with the actual measured force with regard to Fx and Fy. Thus, this model can be used for the prediction of the force history in end-milling with run-out, and it incurs a different force history with different start and exit immersion angles as well as holding effects.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.96-102
• /
• 2000

High speed machining aims to raise the productivity and efficiency by making more precise and higher value-added products than any other machining method by means of the high speediness of spindle and feed drive system. The purpose of this study is to investigate the effects of the run-out of endmill on the dimension precision of workpiece and to obtain the fundamental data on high speed machining which is available by machining the side of Al-alloy with solid carbide endmills in high speed machining center and by measuring dimensions and surface roughness. From the results of experimentation following are obtained ; if spindle speed is ultra high in conditions that radial depth of cut and feed per tooth are very small highly precise and accurate products are to be made efficiently with high feed rate. and so we can raise productivity.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.237-242
• /
• 2001

In this paper, we theoretically analyzed the NRRO(the non-repeatable run-out) of a ball bearing with ball geometric imperfection. The quasi-static and dynamic analysis of a ball bearing was performed to calculate the displacement of shaft center caused by the ball form errors while the shaft is rotating. From consideration of the generating mechanism of NRRO, it is found that the size and form errors of ball generate vibrations with (equation omitted)$\_$c/ and n(equation omitted)$\_$b/${\pm}$(equation omitted)$\_$c/(where n is even) components, respectively. The ball form errors of a ball bearing were precisely measured and NRRO of a ball bearing was calculated using the measured data. A statistical approach was peformed to analyze NRRO of ball bearings with radial errors.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.303-304
• /
• 2002

This paper presents theoretical analysis of the NRRO(the non-repeatable run-out) for a ball bearing with geometric imperfection. This imperfection contains ball size error, ball waviness, outer race waviness and inner race waviness. The 3D dynamic analysis of a ball bearing using the Newton-Raphson method is performed to calculate the displacement of shaft center. The radial and axial NRRO are simulated, and preload and clearance effects are investigated. Preload and clearance have significant effects on radial and axial NRRO of for miniature ball bearings.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.369-374
• /
• 2002

This paper presents theoretical analysis of the NRRO(non-repeatable run-out) for a ball bearing with geometric imperfection. The 3DOF dynamic analysis of a ball bearing using the Newton-Raphson method is performed to calculate the displacement of shaft center. Frequency and magnitude characteristics of radial and axial vibrations are investigated. The ball form errors of the ball, the inner race, and the outer race in a HDD spindle ball bearing are precisely measured. NRRO of a ball bearing is analyzed by using the measured waviness data. It is concluded that dominant components of radial vibrations are ${\Large}f_c\;and\;2{\Larg}f_b{\pm}{\Large}f_c$, and dominant component of axial vibrations is $2{\Large}f_b$. These are generated by the size error and the second waviness of the balls.