• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1888-1893
• /
• 2011

Considering the dynamic performance and stability of railroad vehicles has begun to grab the attention because of developing the high speed train recently. A development based on an analysis of dynamics and verification has to be required to study the stability of vehicle performance. Several ways of analysis were using the look-up table to apply the wheel-rail contact characteristics quickly, whereas there is a constraint of the wheelset lateral displacement. In this study, an development of searching the wheel-rail contact position has been provided. The 2-point contact between wheel and rail during the driving condition can be calculated by numerical analysis. Moreover, a reliability is verified by comparing the result with a commercial program.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1341-1344
• /
• 2005

This study was aimed to verify the acceptable contact force between power collector and 3rd rail type conductor rail for the Korean standardized rubber-tired AGT light rail vehicle. The power collector was designed and manufactured to satisfy the Korean standardized Specifications of the rubber-tired AGT light rail vehicle. Based on the dynamic behavior, contact force variation and interruption in the worst installation tolerance of the conductor rail, its initial contact force was set up. At the test track for the Korean standardized rubber-tired AGT light rail vehicle, interruptions, stresses, vibrations, and contact force variations were measured. As the results, initial contact force was verified to ensure power collection stability.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1277-1278
• /
• 2010

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.225-232
• /
• 2009

Infiltration of rainfall causes railway slopes to be unstable and may result in failure. Basic relationship between the rainfall and stability of railway embankment is defined to analyze its stability by rainfall. An experimental study for defining of infiltration rate of rainfall into slope is conducted in the lab. The results of Rainfall infiltration show that rainfall infiltration is not equal to infiltration as like reservoir because rate of rainfall infiltration is controlled by slope angle. Based on these results, boundary condition of rainfall is altered and various numerical analysis are performed. The variation of shear strength, the degree of saturation and pore-water pressure for railway slope during rainfall can be predicted and the safety factor of railway slope can be expressed as the function of rainfall amount, namely rainfall index. And suggested rainfall index is compared with the rail transport operation control which is used in KORAIL. It is judged that this rainfall index can be a good tool for the rail-transport operation control.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.115-118
• /
• 2007

The geometry of wheel and rail profiles is the primary contributor to wheel and rail interaction. These profiles interact to influence truck steering, vehicle lateral stability, wheel/rail wear and surface damage. Maintaining good control of the profiles is one of the keys to ensuring preferred wheel and rail interaction. Transportation Technology Center, Inc., Pueblo, Colorado, is developing an automated measurement system for wheel/rail contact condition inspections supported by AAR(Association of American Railroads). The system uses a modified version of $WRTOL^{TM}$ (Wheel/Rail Tolerances)--software that performs extensive analysis of wheel and rail contact conditions

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.800-806
• /
• 2011

Thermal expansion which occurs at the high speed rail joint is proportional to the free length from the point of fixity. This thermal expansion behaves similar to free expansion because the girder longitudinal stiffness is much larger than longitudinal resistance of rail pads. But the longitudinal displacement in the long rail is nominal because the longitudinal support condition of the girder is normally MFM(movable-fix-movable) system. Due to these girder expansion characteristics, there is longitudinal relative displacement at the rail pad and rail fastener spring which connects rail and girder. If the relative displacement between rail and girder is beyond the elastic limit for the rail pad, rail fastener system shall be applied using sliding fastener to prevent rail pad damage and fastener separation resulting from slip. On the other hand, train vertical vibration and tilting can occur due to the lack of fastener vertical force if the sliding fastener is applied at the girder joint. In the high speed rail bridge, vibration can occur due to the spring stiffness of the elastomeric bearing, also both vertical downward and upward displacement can occur. The elastomeric bearing vertical movement can cause rail displacement and finally the stability of the ballast is reduced because the gravel movement is induced.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.458-461
• /
• 2007

Recently, the continuous welded rail(CWR) track has been used for less maintenance of the High-speed railway tracks. In case of CWR track, track buckling has always been an unpredictable event under the high compressive stress in rail. The behavior and stress state of CWR track is manily influenced by its thermal variations, and it is important to understand seasonal variations of rail temperature and stress to predict the track stability. This paper describes the in-site measurement for the rail temperature and rail stress, and the correlation between the rail temperature and stress was examined.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.1 s.24
• /
• pp.29-38
• /
• 2007

The research on the track performance and stability of the tilting-train was performed and the settlement of the roadbed was estimated as the tilting train was being operated on the rail joint under the allowable velocity subjected to the track performance and the stability of the tilting-train. Since the impact on the continuous welded rail (CWR) induced by the tilting-train loading is different from the impact on the rail joint, it needs to investigate the settlement of the roadbed beneath the CWR. In this study, when the tilting-train is being operated on the CWR under the allowable velocity subjected to the track performance and the stability of the tilting-train, the settlement and bearing capacity of the roadbed beneath the CWR have been evaluated using numerical analysis and compared with those beneath the rail joint. The numerical results show that the settlements of the roadbed beneath CWR and rail joint are amount to 71.2% and 88.8% of the allowable settlement, respectively. And the stresses are amount to 10.4% and 12.1% of the allowable bearing capacity, respectively.

• Journal of the Korean Society for Railway
• /
• v.5 no.1
• /
• pp.1-9
• /
• 2002

Where the track is continuously welded over the bridge, the longitudinal forces will be distributed interactively between the track and the sub-structure by the rail-bridge interaction mechanism. The ratio between the longitudinal forces transmitted in each elements depends on the magnitude of the ballast resistance and the stiffness of the sub-structures. In this paper, the main factors affect on the longitudinal rail force are discussed and the parametric study for the behavior of CWR(Continuous Welded Rail) track was executed. It is concluded that the horizontal ballast resistance and the stiffness of the bridge sub-structure are the significant parameters affecting the stability of the continuous welded rail track.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.679-685
• /
• 2003

Rotem has been using VAMPIRE for simulation and verification of the railway vehicle design. To improve the capability and accuracy of the analysis ability, ADAMS/Rail has been chosen as the next generation analysis tool. The dynamic performance of the railway vehicle, which is designed and manufactured by Rotem, is analyzed and simulated using ADAMS/Rail. The critical speed for linear and non-linear stability on tangent track, curving performance on various curved tractk, ride quality, derailment coefficient and the eigen values are calculated. In this paper, the results from ABAMS/Rail are compared with VAMPIRE's results.