• International Journal of Railway
• /
• 제7권4호
• /
• pp.109-116
• /
• 2014

For optimization of a low-noise track system, rail vibration and noise radiation needs to be investigated. The main influencing parameters for the noise radiation and the quantitative results of every track system can be obtained using a calculation model of generation and radiation of railway noise. This kind of model includes contact modeling and the calculation model of the dynamic properties of the wheel and the rail. This study used a nonlinear wheel/rail interaction model in the time domain to investigate the excitation of the rolling noise. Wheel/rail response is determined by time integrating Green's function of the rail together with force impulses from the wheel/rail contact. This model and the results of the study can be used for supporting calculation with the conventional model by an addition of the contributions due to nonlinearities to the roughness spectrum.

• 소음진동
• /
• 제10권3호
• /
• pp.444-450
• /
• 2000

Wheel-rail noise is normally classified into three catagories : rolling impact and squeal noise. In this paper rolling noise caused by the irregularity between a wheel and a rail is analysed as follows: The irregularity between the wheel and the rail is assumed as linear superposition of sinusoidal profiles. Wheel-rail contact stiffness is linearized by using Hertzian contact theory and then contact force between the wheel and the rail is calculated. vibration of the rail and the wheel is calculated theoretically by receptance method or FEM depending on the geometry of the wheel or the rail for the frequency range of 100-500 Hz important for noise generation. The radiation noise caused by those vibration response is computed by BEM To verify this analysis tools rolling noise is calculated by proposed analysis steps using typical roughness data and these results are compared with experimental rolling noise data. This analysis tools show reasonable results and finally used for the prediction of the Korean high speed train rolling noise.

• Structural Engineering and Mechanics
• /
• 제48권4호
• /
• pp.455-466
• /
• 2013

In recent years, many countries have added railway noise to the issues covered by noise regulations. It is known that the rail is the dominant source of rolling noise at frequency range of 500Hz-2000Hz for the conventional speeds (<160km/h). One of the effective ways to reduce noise from railway track is using a rail vibration absorber. To study the acoustic performance of rail absorber, the decay rates of vibration have long been used by researcher. In this paper, A FE model of a periodic supported rail with infinite element in ABAQUS is developed to study the acoustic performance of the rail absorber. To compute the decay rates, acceleration responses along the rail transferred to MATLAB to obtain response levels in frequency domain and then by processing the response levels, the decay rates obtained for each1/3octav band. Continous rail absorber is represented by a steel layer and an elastomer layer. The decay rates for conventional rail and rail with one-side absorber and also, the rail with two side absorber are obtained and compared. Then, to improve the system of rail absorber, a steel plate with elastomer layer is added to bottom of the rail foot. The vertical decay rate results show that the decay rate of rail vibration along the track is significantly increased around the tuned frequency of the absorber and thus the rail vibration energy is substantially reduced in the corresponding frequency region and also effective in rail noise reduction.

• 소음진동
• /
• 제10권3호
• /
• pp.486-492
• /
• 2000

The major source of railway noises is rolling noise caused by the interaction of the wheels and rails. This rolling noise is generated by the roughness of the wheel /rail surface on tangent track in the absence of discontinuities such as wheel flats or rail joints. These roughness cause relative vibrations of the wheel and rail at their contact area. The vibrations generated at the contact area are treansmitted through the wheel and rail structures exciting resonances of the wheel and travelling waves in the rail. Then these vibrations radiate noise to the wayside. In this paper we predict the rollingnoise radiated from radial/axial motion of the wheel and vertical/lateral motion of the rail using Remington's analytical model and then compare of the predicted sound pressure and measured one. Although there are some inaccuracy in our prediction. these results show in good agreement between 500 Hz and 3150 Hz.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.555-564
• /
• 2001

Wheel-rail noise is normally classified into three catagories ： rolling, squeal and impact noise. In this paper, rolling noise caused by the irregularity between a wheel and rail is analysed as follows： The irregularity between the wheel and rail is assumed as combination of sinusoidal profiles. Wheel-rail contact stiffness is linearized by using Hertzian contact theory, and then contact force between the wheel and rail is calculated. Vibration of the rail and wheel is calculated theoretically by receptance method or FEM depending on the geometry of wheel or rail for the frequency range of 100-5000Hz, important for noise generation. The radiation caused by those vibration is computed by BEM. To verify this analysis tools, rolling noise is calculated by preceding analysis steps using typical roughness data and it is compared with experimental rolling noise data. This analysis tools show reasonable results and used for the prediction of KTX rolling noise.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.161-164
• /
• 2010

The surface roughness of wheels and rails are known to be major contributory factors in wheel-rail rolling noise. Generally, the rail roughness was greater than the wheel roughness. Generally, rolling noise sizes and noise level in compliance with wheel/rail roughness almost are reported with the fact that is similar. Rolling noise important factors rightly being in compliance with roughness of contact point regions of the wheel/the rail, presented from the present paper.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.119-126
• /
• 2009

The noise emitted during train operation is generated with various reasons. It is known that the major noise generation is classified according to the ranges of train speed; that is, engine noise at lower speed range, rolling noise at medium speed range, and air-borne noise at higher speed range. These noises are transmitted in combined form with the noises generated from track components and under-carriage, etc. The rolling noise as a major noise at medium speed range is caused by the vibration occurred at wheel/rail interface. The vibration occurred at wheel/rail interface is transmitted to wheel and rail, and this vibration is emitted from wheel and rail as a noise. In this paper, a soundproof box which can simply measure the noise emitted from rail and analyze the characteristics of the measured noise is studied.

• Smart Structures and Systems
• /
• 제18권5호
• /
• pp.1063-1085
• /
• 2016

Taking advantage of the high sensitivity and long-distance detection capability of acoustic emission (AE) technique, this paper focuses on the crack detection in rail head, which is one of the most vulnerable parts of rail track. The AE source location and noise cancellation were studied on the basis of practical rail profile, material and operational noise. In order to simulate the actual AE events of rail head cracks, field tests were carried out to acquire the AE waves induced by pencil lead break (PLB) and operational noise of the railway system. Wavelet transform (WT) was first utilized to investigate the time-frequency characteristics and dispersion phenomena of AE waves. Here, the optimal mother wavelet was selected by minimizing the Shannon entropy of wavelet coefficients. Regarding the obvious dispersion of AE waves propagating along the rail head and the high operational noise, the wavelet transform-based modal analysis location (WTMAL) method was then proposed to locate the AE sources (i.e. simulated cracks) respectively for the PLB-induced AE signals with and without operational noise. For those AE signals inundated with operational noise, the Hilbert transform (HT)-based noise cancellation method was employed to improve the signal-to-noise ratio (SNR). Finally, the experimental results demonstrated that the proposed crack detection strategy could locate PLB-simulated AE sources effectively in the rail head even at high operational noise level, highlighting its potential for field application.

• 한국철도학회논문집
• /
• 제18권4호
• /
• pp.289-300
• /
• 2015

철도 전동 소음은 철도에서 발생하는 대표적인 소음으로서 차륜과 레일의 음향 조도에 의해 가진 된 차륜 및 레일의 진동으로부터 발생한다. 철도 전동 소음 해석 시 레일 방사 소음은 자유 공간에 놓인 레일의 음향 방사 파워를 이용해 원거리에서 계산하므로, 일반적으로 소음원 모델에 지면 반사를 고려하지 않는다. 그러나 레일 주위의 근접 음장을 해석하고 저감 대책을 적용하기 위해서는 지면에 의한 음파의 반사를 고려해야 한다. 본 논문에서는 파수유한요소/경계요소법을 이용해 지면에 의해 발생하는 레일 소음의 변화와 그 특성을 살펴보았다. 해석은 먼저 레일이 강체 지면에 부착된 경우와 레일 패드 높이만큼 강체 지면에서 이격된 경우에 대해 방사효율을 구하고 그 결과를 비교하였다. 이를 통해 레일과 강체 지면의 이격 여부에 따라 레일 방사 소음에 크게 변화함을 확인하였다. 둘째로는 지면에 임피던스 경계조건을 부여하고 레일에서 방사되는 음향 파워 및 지향 특성의 변화를 살펴보았다.

• 한국철도학회논문집
• /
• 제4권1호
• /
• pp.31-37
• /
• 2001

There are three examples of noise reduction test by joint improvement. One of them is tested for electric car at joint rail and another is tested at expansion joint and long welded rail and the third is tested at open deck bridge. We can know from the result that the noise reduction effect of rail welding is very different to the type of track and the car. The condition of the test has some differences, but it may be useful reference of noise reduction