• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.59-62
• /
• 2008

The performance behavior of solid oxide fuel cell using reformate gas as fuels was investigated. When the pre-reformate gas was used without steam, the maximum power density was 50% lower than that using H2. This may be due to carbon deposition caused by the pyrolysis of remaining hydrocarbons. However, when the steam was added, the maximum power density showed a relatively small variation according to reformate gas. When pre-reformate gas with steam was fed into anode, the SOFC showed the stable performance without sharp voltage drop during 10h operation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.5-8
• /
• 2008

SOFC (Solid oxide fuel cell) has an advantage in the term of fuel flexibility, comparing with other kinds of fuel cells. In SOFC and fuel reformer cooperation system, the reformate gas with the various $H_2$/CO ratios is delivered into the anode of SOFC. In this situation, electrochemical oxidation reactions of the reformate gas in the anode are complex and competitive. In this paper, the effects of the composition of $H_2$ and CO on the overall electrochemical oxidation at Ni-YSZ anode are studied by testing the open circuit voltage (OCV) and current-voltage characteristics of single cells.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.78.1-78.1
• /
• 2010

The metal-supported solid oxide fuel cell (SOFC) was studied. Hydrocarbon fueled operation is necessary to make SOFC system. Different operating characteristics for metal-supported SOFC are used than for conventional ones as hydrocarbon fueled operation. Metal-supported SOFC was successfully fabricated by a high temperature sinter-joining method and the cathode was in-situ sintered. Synthetic gas, which is compounded as the diesel reformate gas composition and low hydrocarbons was completely removed by the diesel reformer. Metal-supported SOFC with synthetic gas was operated and evaluated and its characteristics analyzed. Button cell and $5{\times}5cm^2$ single stack were mainly operated and analyzed. Long-term operation using diesel reformate shows degradation, and degradation analysis was completed in the view of metal oxidation. Solution to increase stability of long-term operation was tried in the way of materials and operating conditions. Finally, $5{\times}5cm^2$ metal-supported single stack using synthetic gas was operated for 1000 hours under the modified condition.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.773-776
• /
• 2009

In this paper, new concept of the diesel fuel processing is introduced for the stable operation of solid oxide fuel cells (SOFCs). Heavier hydrocarbons than $CH_4$, such as ethylene, ethane, propane, and etc., induce the carbon deposition on anode of SOFCs. In the reformate of heavy hydrocarbons (diesel, gasoline, kerosene, and JP-8), concentration of ethylene is usually higher than low hydrocarbons such as ethane, propane, and butane. So, removal of low hydrocarbons (over C1-hydrocarbons), especially ethylene, at the reformate gases is important for stable operation of SOFCs. New methodology as named "post-reformer" is introduced for removing the low hydrocarbons at the reformate gas stream. Catalyst of the NECS-PR4 is selected for post-reforming catalyst because the catalyst of NECS-PR4 shows the high selectivity for removing low hydrocarbons and achieving the high reforming efficiency. The diesel reformer and post-reformer are continuously operated for about 200 hours as integrated mode. The reforming performance is not degraded and low hydrocarbons in the diesel reformate are completely removed.

• Journal of Environmental Science International
• /
• v.17 no.12
• /
• pp.1307-1314
• /
• 2008

Hydrogen gas is used as a fuel for the proton exchange membrane fuel cell (PEMFC). Trace amount of carbon monoxide present in the reformate $H_2$ gas can poison the anode of the PEMFC. Therefore, preferential oxidation (PROX) of CO is essential for reducing the concentration of CO from a hydrogen-rich reformate gas. In this study, conventional Pt/$Al_2O_3$ catalyst was prepared for the preferential oxidation of CO. The effects of catalyst preparation method, additive, and hydrogen on the performances of PROX reaction of CO were investigated. Water treatment and addition of Ce enhanced catalytic activity of the Pt/$Al_2O_3$ catalyst at low temperature below $100^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.218-221
• /
• 2009

Solid oxide fuel cells (SOFCs), as high-temperature fuel cells, have various advantages. In some merits of SOFCs, high temperature operation can lead to the capability for internal reforming, providing fuel flexibility. SOFCs can directly use CH4 and CO as fuels with sufficient steam feeds. However, hydrocarbons heavier than CH4, such as ethylene, ethane, and propane, induce carbon deposition on the Ni-based anodes of SOFCs. In the case of the ethylene steam reforming reaction on a Ni-based catalyst, the rate of carbon deposition is faster than among other hydrocarbons, even aromatics. In the reformates of heavy hydrocarbons (diesel, gasoline, kerosene and JP-8), the concentration of ethylene is usually higher than other low hydrocarbons such as methane, propane and butane. It is importatnt that ethylene in the reformate is removed for stlable operation of SOFCs. A new methodology, termed post-reforming was introduced for removing low hydrocarbons from the reformate gas stream. In this work, activity tests of some post-reforming catalysts, such as CGO-Ru, CGO-Ni, and CGO-Pt, are investigated. CGO-Pt catalyst is not good for removing ethylene due to low conversion of ethylene and low selectivity of ethylene dehydrogenation. The other hand, CGO-Ru and CGO-Ni catalysts show good ethylene conversion, and CGO-Ni catalyst shows the best reaction selectivity of ethylene dehydrogenation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.558-565
• /
• 2008

Solid oxide fuel cell(SOFC) has a higher fuel flexibility than low temperature fuel cells, such as polymer electrolyte fuel cell(PEMFC) and phosphoric acid fuel cell(PAFC). SOFCs also use CO and $CH_4$ as a fuel, because SOFCs are hot enough to allow the CH4 steam reformation(SR) reaction and water-gas shift(WGS) reaction occur within the SOFC stack itself. Diesel is a good candidate for SOFC system fuel because diesel reformate gas include a higher degree of CO and $CH_4$ concentration than other hydrocarbon(methane, butane, etc.) reformate gas. Selection of catalyst for autothermalr reforming of diesel was performed in this paper, and characteristics of reforming performance between packed-bed and microchannel catalyst are compared for SOFC system. The mesh-typed microchannel catalyst also investigated for diesel ATR operation for 1kW-class SOFC system. 1kW-class diesel microchannel ATR was continuously operated about 30 hours and its reforming efficiency was achieved nearly 55%.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.4
• /
• pp.474-480
• /
• 2011

Hydrocarbon is required to be converted to pure hydrogen without carbon monooxide (CO) for polymer exchange membran fuel cell (PEMFC) applications. In this paper, CO cleaning processes as the downstream of Dimethyl ehter (DME) autothermal reforming process were performed in micro-reactors. Our study suggested two kinds of water gas shift (WGS) reaction process: High Temperature shift (HTS) - Low Temperature shift (LTS), Middle temperature shift (MTS). Firstly, using perovskite catalyst for MTS was decreased effieiciency since methanation. Using HTS-LTS the CO concentration was decreased about 2% ($N_2$ & $H_2O$ free) with the reaction temperature of $420^{\circ}C$ and $235^{\circ}C$ for HTS and LTS, respectively. As the final stage of CO cleaning process, preferential oxidation (PROX) was applied. The amount of additional oxygen need 2 times of stoichiometric at $65^{\circ}C$. The total conversion reforming efficiency of 75% was gained.

• Korean Chemical Engineering Research
• /
• v.51 no.4
• /
• pp.455-459
• /
• 2013

The fuel processor for the portable fuel cell includes multi-step processes consisting of hydrogen generator, heat generator and several CO clean-up stages. One of requirements of the fuel processor for portable fuel cell system is a rapid start-up time. Especially, the warm-up time for WGS reactor is crucial factors for total start-up time. In this paper, active heating protocol, which is the heating protocol of WGS reactor supplied by the oxidation of CO rich reformate in the initial stage, is used for a rapid start-up. The air stream fed to the inlet of WGS reactor rapidly oxidize the CO rich reformate in the WGS reactor. Therefore, CO concentration in reformate quickly stabilized at the desired concentration without CO surges.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.99.1-99.1
• /
• 2011

Reactant mixing has a critical role in ensuring reformate quality and an important design objective is to achieve sufficiently complete mixture of reactants. For that purpose it is required to understand the coupled transport-kinetics phenomena in the mixing region. Three-dimensional computational fluid dynamics model was developed and validated in previous works. The mixing characteristics in various alternatives of a prototype mixing chamber were compared, and then a reduced reaction kinetics was applied to two extreme designs for investigating the impact of gas-phase reactions. Both designs did not reach threshold ethylene mole fraction of 0.001, but surprisingly more ethylene was generated in the design having better mixing characteristics. The presentation will deliver the development process of coupled transport and kinetics model briefly and the detailed information about the mixing characteristics and gas-phase reactions in two mixer designs.