• 한국세라믹학회지
• /
• 제29권1호
• /
• pp.15-22
• /
• 1992

The reason for permanent shrinking of recycled castable refractories from alumino-silicate waste refractories was investigated and the method to control shrinking is suggested in order to increase maximum service termperature. The porosity of castable refractories with waste material as large aggregate decreases after heat treatment because the porosity of waste refractories is greater than the of green material, in which CaO around large aggregate penetrates into aggregate and promotes liquid phase sintering. The shrinking of recycled castable refractories resulted in the decrease in porosity can be controled by addition of green kaolin chamotte as large aggregate. The shrinking of recycled castable refractories caused by the differences in densities of mineral phases before and after heat treatment can be controled by addition of kyanite. The use of green kaolin chamotte and kyanite increases the service temperature of recycled castable refractories up to 1500$^{\circ}C$.

• 한국세라믹학회지
• /
• 제40권12호
• /
• pp.1141-1149
• /
• 2003

Refractory industry in technologically advanced countries has long been on gradual decline due to leveled-off steel production and decreasing unit consumption of refractories for steel. Notable technological achievements by refractory industry that contributed significantly to steel production are briefly reviewed covering from blast furnace, basic oxygen furnace to continuous casting. Future possibility to revitalize the refractory industry is discussed on the basis of the review, taking into account opportunities available in environment and energy related sector of industries.

• 한국결정성장학회지
• /
• 제25권1호
• /
• pp.27-31
• /
• 2015

내화물은 슬래그 등과의 화학반응뿐만 아니라 입자 충돌이나 마찰에 의한 물리적인 마모도 일어난다. 그러나 내화물의 에로젼에 의한 마모에 대해서는 거의 알려져 있지 않다. 본 실험에서는 내화도가 1300과 $1500^{\circ}C$인 캐스터블에 대해서 SiC 마모입자의 입사 각도에 따른 마모량의 변화를 분석하였다. 그 결과 최대 마모량을 나타내는 각도는 입자가 내화물에 수직으로 부딪힐 때가 아니라 $60{\sim}75^{\circ}$로 입사될 때인 것을 알았다. 또한 내화물의 기공률이 에로젼 마모에 가장 큰 영향을 미치는 것으로 생각되었다.

• 한국세라믹학회지
• /
• 제36권8호
• /
• pp.876-885
• /
• 1999

In order to develop high performance basic dam block for tundish vessel in steel-making binders and additives on hydration and thermal characteristics of magnesiz castable refractories were studied. Crack initiation and propagation in cement bonded magnesia castables due to slaking of magnesia clinker at drying process were suppressed by using spinel clinker instead of magnesia powder. In case of Na2O$.$2CaO$.$P2O5(NC2P) bonded castable crack initiation due to slaking of magnesia clinker did not occur but bending strength at high temperature was low. Mechanical properties of NC2P bonded castable refractories at high temperature were improved by using magnesia clinker that contains low SiO2 contents.

• 한국세라믹학회지
• /
• 제56권1호
• /
• pp.77-83
• /
• 2019

MgO-C refractories are used in basic furnaces and steel ladles due to their many desirable properties, such as excellent thermal shock resistance via low thermal expansion, and high thermal conductivity. However, the mechanical and thermal properties of the refractory continuously deteriorate by spalling phenomena and pore generation due to the oxidation of graphite, used as a carbon source, indicating that the characteristics and performance of MgO-C refractories need to be improved by using a new material or composition. In this study, the use of a Hertzian indentation test as a method for determining the damage and fracture behavior of an MgO-C refractory is described. The results highlight that Hertzain indentation tests can be one of the important evaluation tools for quasi-plastic damage accumulation of MgO-C refractories during falling process of scrap metal.

• 한국환경보건학회지
• /
• 제21권4호
• /
• pp.17-23
• /
• 1995

As a basic experiment to develope biological pretreatment proces~ in water treatment, the experiments on biodegradability and isothermal adsorption of activated carbon were performed on refractories such as humic acid, $NH_3-N$, phenol and ABS which caused the problems in drinking water treatment. Also, the treatabilities on humic acid were examined in the continuous flow type reactors. The removal efficiencies of humic acid, $NH_3-N$, phenol and ABS in the biodegradable experiments for 5 days were 20.1%, 73.4%, 91.7% and 97.5%, respectively. In the isothermal adsorption test of refractories on activated carbon to be used as a media in the continuous flow type reactors, ABS and phenol are adsorbed easily, but humic acid and $NH_3-N$ are difficult to be done. The removal efficiencies of humic acid in granular activated carbon(GAC) reactor were about 7-8% higher than in biological activated carbon(BAC) reactor. The removal efficiencies of humic acid in biological fluidized bed(BFB) reactor were about 30% in GAC media, but were almost zero in sea sand media.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.345-351
• /
• 1998

Thermal shock resistance of $Al_2O_3$- and Fe-$Al_2TiO_5$-based Castable Refractories was studied using a central heating technique. Ring type specimens, 10mm thick and 20 and 100mm inner and outer diameters, respectively, were rapidly heated on the internal surface of the centre hole using a high power electrical heating element. The temperature field was measured experimentally and modelled using finite element analysis (FEA). The thermal stress field was also modelled using FEA. A radial notch was introduced to the ring specimens to enable calculation of the thermal stress intensity factors (SIF). A special LVDT device was incorporated in the thermal shock tester to monitor crack mouth opening displacement (COD). The thermal shock fracture initiation and crack propagation behaviour of the castable refractories were ascertained using the COD measurements and the fracture mechanics analysis data.

• 한국세라믹학회지
• /
• 제27권7호
• /
• pp.877-882
• /
• 1990

Effects of metallic Al powder addition on basic and thermal properties of castable refractories were investigated. Generally, low grade prooperties were obtained by metallic Al powder addition with the increase of temperature, comparing with those of non-addition of Al powder. Especially, Al addtion showed severe shrinkage, corrosiion and low strength above 1000$^{\circ}C$. As a result of Al addition, lower strength of and higher corrosion resistance were shown for 2% addition, but it was reversed for above 4% addition. It was found that Al addition was excellent in the explosive spalling test regardless of Al quantity.

• 한국세라믹학회지
• /
• 제23권1호
• /
• pp.51-59
• /
• 1986

It was the first time the MgO-C brick was developed for the lining materials in the hot spots in electric are furnace in 1972. MgO-C brick is high registant to thermal and structural spalling. Futhermore for the reason that carbon is hard to react with slag and MgO is high fireproof MgO-C brick shows a high corrosion registance to slag attack compared with conventional basic refractories. Owing to their excellent properties the use of MgO-C refractories are being developed widely in the field of shaped refractories and even in that of monolithic refractories. In this paper the oxidation of carbon the infiltration of slag into the brick texture and effects of additions were investigated. The results obtained were as follows : 1) The use of fused MgO-clinker and high purity carbon as raw materials increased the corosion registance and hot modulus of rupture of MgO-C brick. 2) As the oxidation reaction of the carbon proceeded the slag infiltrated into the brick texture. And then the slag components reacted with the MgO grains and formed low melting point compounds particulary CaO.MgO.$SiO_2$ and 3CaO.MgO.$2SiO_2$ that resulted in the wear of the brick. 3) It is recongnized the Al, Si, $B_3C$ effects on the oxidation registant properties of MgO-C brick by contribu-ting to the decrease of permeability according to the formation of $Al_4C_3$, SiC, $B_2O_3$ and the decrease of open pores relating to the formation of MgO.Al2O3, $SiO_2$, 3MgO.$B_2O_3$ at the decarbonized layer.

• 자원리싸이클링
• /
• 제12권3호
• /
• pp.46-53
• /
• 2003

알루미늄드로스의 재활용은 알루미늄 재생지금 제조시에 요구되는 중요한 사항 중의 하나이다. 본 연구에서는 국내 재생 알루미늄업체에서 발생된 알루미늄드로스를 처리하여 알루미나질 내화물 원료로 재활용하고자 하였다. 드로스 시료를 크기에 따라 선별하고, 1 mm보다 작은 크기의 드로스를 수산화나트륨 용액으로 침출하여 드로스 중의 잔류 알루미늄을 용액 중으로 분리 추출하고, 침출용액에서 석출반응에 의하여 수산화알루미늄을 회수하였다. 드로스 중의 금속알루미늄을 회수한 후 발생된 침출잔사는 수세, 건조, 배소와 같은 일련의 처리를 하여 드로스 중의 잔류 금속성분을 산화물 형태로 변환시켰다. 배소 처리한 드로스 잔사를 골재 및 점결제와 배합하여 알루미나질 캐스타블내화물을 만들고, 굽힘강도와 압축강도를 시험한 결과 KS 기준치인 굽힘강도 $25\;kg/\textrm{m}^2$ 이상, 압축강도 $80\;kg/\textrm{cm}^2$ 이상을 만족하였다. 본 연구결과를 알루미늄드로스를 효율적으로 재활용할 수 있는 한가지 방안으로 제안하고자 한다.