• Journal of Welding and Joining
• /
• v.6 no.3
• /
• pp.21-26
• /
• 1988

The behavior of angular distortion in butt joint wleding of thin plate structure is investigated with an experimental model and partially with a computational model. The experimental model studying the effects of specimene size and degree of restraint on the angular distorion offers a good method for analyzing the behavior of the distrotion. In addition, the distrotion during welding was demonstrated by both experimental measurement and numericla prediciton. The facts evealed in this study are as follows : 1) distrotion angles were changed with variations of specimene wldth. 2) With the restraint, angular distrotion was reduced to 20% to that of free joint. 3) After the restraint being removed, the effect of restraint was also remained. 4) Same heat input per unit thickness caused same amount of distortion. 5) The mode of angular distortion was expected to be changed with expected to be changed with time, i.e. convex movement during heating and concave one during cooling.

• Steel and Composite Structures
• /
• v.4 no.1
• /
• pp.23-36
• /
• 2004

The inelastic lateral-distortional buckling of doubly-symmetric hot-rolled I-section beam-columns subjected to a concentric axial force and uniform bending with elastic restraint which produce single curvature is investigated in this paper. The numerical model adopted in this paper is an energy-based method which leads to the incremental and iterative solution of a fourth-order eigenproblem, with very rapid solutions being obtained. The elastic restraint considered in this paper is full restraint against translation, but torsional restraint is permitted at the tension flange. Hitherto, a numerical method to analyse the elastic and inelastic lateral-distortional buckling of restrained or unrestrained beam-columns is unavailable. The prediction of the inelastic lateral-distortional buckling load obtained in this study is compared with the inelastic lateral-distortional buckling of restrained beams and the inelastic lateral-torsional buckling solution, by suppressing the out-of-plane web distortion, is published elsewhere and they agree reasonable well. The method is then extended to the lateral-distortional buckling of continuously restrained doubly symmetric I-sections to illustrate the effect of web distortion.

• Journal of Welding and Joining
• /
• v.30 no.5
• /
• pp.51-56
• /
• 2012

The purpose of this study is to evaluate the distortion and the residual stress of GTA tubular welds between tube and head. In order to do it, the heat input model for GTA welding process was first developed by experiment and FE analyses. The welding distortion and the residual stress distribution of the tubular welds according to welding pass and various restraint degrees were evaluated by using FEA with the heat input model. From FEA results, it was found that the residual stress and the radial distortion at the weld toe of tube part decrease with a decrease in the number of welding pass. However, the maximum residual stresses in each direction of tubular welds are almost constant regardless of the external restraint degree. It was mainly due to the high internal restraint of the welds.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.1
• /
• pp.94-100
• /
• 2001

Distortion is a potential problem with all welded fabrication and should be caused dimensional changes and mismatch of joints during welding fabrication. Correction unacceptable weld distortion is extremely costly and in some case impossible. The aim of the present work is to verify the variation of the compressive force, tensile force and distortion during plastic deformation under Tungsten-inert-gas(TIG) welding, on type 304 stainless steel. Experimental results show that possibili-ty if measuring deformation during welding and good correlation was found between analytical and experimental result ad finite element methods have been used to model temperature analysis.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.254-256
• /
• 2004

The purpose of this study is to establish the control method of angular distortion at the weldment of the pressure hull penetration. In order to do it, comprehensive experiment and FEA were performed to evaluate the distortion behavior for the weldment of HY-100. Based on the results, a proper deposit sequence for the both sides X groove penetration weldment was established. In addition, a proper welding sequence was proposed by evaluation of bending restraint intensity with size and position of pressure hull penetration.

• Steel and Composite Structures
• /
• v.5 no.4
• /
• pp.305-326
• /
• 2005

The inelastic buckling behaviour of continuously restrained two and three-span continuous beams subjected to concentrated loads and uniformly distributed loads are studied in this paper. The restraint type considered in this paper is fully restrained against translation and elastic twist applied at the top flange. These types of restraints are most likely experienced in industrial structures, for example steel-concrete composite beams and half through girders. The buckling analysis of continuous beam consists of two parts, firstly the moment and shear distribution along the member are determined by employing force method and the information is then used for an out-of-plane buckling analysis. The finite element method is incorporated with so-called simplified and the polynomial pattern of residual stress. Owing to the inelastic response of the steel, both the in-plane and out-of-plane analysis, which is treated as being uncoupled, extend into the nonlinear range. This paper presents the results of inelastic lateral-torsional and lateral-distortional buckling load and finally conclusions are drawn regarding the web distortion.

• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.165-167
• /
• 2001

• Steel and Composite Structures
• /
• v.2 no.4
• /
• pp.297-314
• /
• 2002

An energy method of analysis is presented which can be used to study the inelastic lateral-distortional buckling of hot-rolled I-sections continuously restrained at the level of the tension flange. The numerical modelling leads to the incremental and iterative solution of a fourth-order eigenproblem, with very rapid solutions being obtainable, so as to enable a study of the factors that influence the strength of continuously restained I-beams to be made. Although hot-rolled I-sections generally have stocky webs and are not susceptible to reductions in their overall buckling loads as a result of cross-sectional distortion, the effect of elastic restraints, particularly against twist rotation, can lead to buckling modes in which the effect of distortion is quite severe. While the phenomenon has been studied previously for elastic lateral-distortional buckling, it is extended in this paper to include the constitutive relationship characteristics of mild steel, and incorporates both the so-called 'polynomial' and 'simplified' models of residual stresses. The method is validated against inelastic lateral-torsional buckling solutions reported in previous studies, and is applied to illustrate some inelastic buckling problems. It is noted that over a certain range of member slenderness the provisions of the Australian AS4100 steel standard are unconservative.

• Structural Engineering and Mechanics
• /
• v.2 no.1
• /
• pp.113-123
• /
• 1994

A method for computing the elastic buckling prestressing force of a post-tensioned composite steel-concrete tee-beam is presented. The method is based on a virtual work formulation, and incorporates the restraint provided by the concrete slab to the buckling displacements of the steel beam. The distortional buckling solutions are shown to be given by a quadratic equation. The application of the analysis to calculation buckling strengths is given, based on codified rules for beam-columns. Conclusions are then drawn on the importance of distortional buckling when a post-tensioned composite beam is stressed during jacking.

• Journal of Oriental Neuropsychiatry
• /
• v.17 no.2
• /
• pp.1-13
• /
• 2006

Objective : This study examined whether Yangsung program (oriental psychological weight regulation model based on Confucian ideas) is effective on weight loss, self esteem, three factor on eating questionnaires(restraint eating, disinhibition and hunger), distortion of body-image and biochemistry of blood. Method : 23 women were assigned randomly into 2 groups; experimental group(n=10) and control group(n=13). Experimental group had 7 personal sessions consisting of personal Yangsung therapy, meditation, general diet and exercise education. Control group had personal sessions with general diet and exercise education once a week for 6 weeks. All subjects were weighed and evaluated with Rosenberg self esteem scale, distortion of body-image, biochemistry of blood and three factor eating questionnaires at the beginning and end of the program. Result : There is significant difference between two groups in changes of self esteem, disinhibition and hunger(p<0.05). There is no significant difference in weight reduction and BMI between two groups. Conclusion : This study showed a new possibility of unique psychological program for obesity characterized by its philosophical context.