• Journal of the KSME
• /
• v.16 no.2
• /
• pp.100-107
• /
• 1976

Stress analysis of tapered cylinder of reactor vessels is investigated by means of the intersection method. The tapered cylinder is approximated into three models-average cylinder, conical frustum, and ring. The results are compared with those of the finite element method program and an experiment. In this paper, the following results are obtained: (1) the best aproximation has been obtained by the ring model analysis: (2) the intersection analysis of the tapered cylinder by the ring model shows a sufficient accuracy for the stress analysis of reactor vessels.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.1
• /
• pp.55-77
• /
• 2012

A Modern Rock TBM is a tunnel excavation method combining the conventional tunnelling method with the mechanized tunnelling method. It is a hybrid system that excavates a tunnel with TBM and supports the ground by ring beam, wire mesh, rock bolt, shotcrete, i.e., conventional tunnelling method. In the Modern Rock TBM, a ring beam is similar to a steel rib in NATM in the way that uses H-beam. But using a ring beam is more effective than a steel rib because it is installed in a closed-circle. Therefore, improving the performance of the ring beam is a key factor for achieving tunnel stability. In this respect, this study introduces a pressurized ring beam that might be functioning more effectively by confining convergence during tunnel excavation. In order to verify the effect of the pressurized ring beam, a three-dimensional numerical analysis was conducted. The numerical analysis confirms an increase in the minimum principal stress and reduction in the plastic strain that triggers excessive displacement. The analysis result also indicates a decrease in the relative displacement occurring after installing the ring beam, and expansion in spacing between the ring beams.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.12
• /
• pp.2670-2677
• /
• 2002

The ring rolling process involves three-dimensional non-steady material flow and continuous change of radius and thickness of the ring workpiece. In this study, the deformation analysis and geometric updating algorithm of the ring rolling process were verified by using the three-dimensional rigid-plastic finite element method. Manufacturing processes for plain ring and T-shaped ring were investigated by comparing experiments with simulation results, especially in side spread, load-stroke and pressure distribution, showing a good agreement. It was concluded that the simulation method would be a useful tool for the design of a ring rolling process.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.1
• /
• pp.50-53
• /
• 1999

In this paper, the mechanical movement of lip seal-ring which plays the most important function in stern-tube sealing system and the possibility of leakage caused by pressure fluctuation are studied by theory and experiment. By the finite element method for axial symmetry object which receives the torsional bending load, the displacement and stress analysis of the seal-rings are executed for products of several representative manufacturers of seal-rings, and also the possibility of crack occurance are checked by theoretical analysis. A sample seal-ring id designed and manufactured using the program of displacement and stress analysis developed in this study and made an experimental apparatus to test the sampling seal-ring. The sampling seal-ring functioned excellently, but it had its durability and this problem may be solved by using the Viton instead of NBR.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.1038-1043
• /
• 2002

The floating ring journal bearing is attraction for high-speed turbo machinery applications, including turbochargers and aircraft accessory equipment, because it is not only simple and easy to make and to replace in the field but also it seems to have adequate high speed stability characteristics. Therefore, an analysis method of dynamic properties of floating ring journal bearing is presented. The static equilibrium locus of inner film and outer film are calculated by using the impedance description. The equivalent stiffness and damping coefficients of floating ring journal bearing are composed by using the equilibrium of torque between inner film and outer film. Then, a stability analysis of turbocharger shaft system supported with floating ring journal bearing has been performed.

• Journal of Mechanical Science and Technology
• /
• v.14 no.9
• /
• pp.928-934
• /
• 2000

This paper describes a method developed for the simulation of ring pack lubrication characteristic in an internal combustion engine. In general, the quantity of oil supply for piston ring lubrication may be insufficient in filling the entire volume formed at the interference between the piston ring and the cylinder liner. Thus the oil starvation condition should be considered in analyzing piston ring lubrication. In order to reasonably estimate the amount of oil left over on the cylinder liner, the flow rate at the posterior portion of the interface should be calculated with an adequate boundary condition that confirms flow continuity condition. In this analysis, oil starvation and open-end boundary conditions are considered at the inlet and outlet of the piston rings. The lubrication characteristic of each piston ring is obtained by an iterative method with sequential steps. It is revealed that piston rings are operated under oil starvation in most operating cycles and the result under these conditions are quite different from that with the fully-flooded assumption.

• Tribology and Lubricants
• /
• v.8 no.1
• /
• pp.38-43
• /
• 1992

In solving the Reynolds equation in dynamically loaded bearing problem, it is almost impossible to find the squeeze velocity and the cavitation region by analytical method. Finite Element Method was applied to the piston-ring lubrication analysis to solve the complementary problem. The method was very efficient and any convergence problem was not encountered.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.404-406
• /
• 2002

In this paper, the method of image feature extraction is proposed. This method employ the energy field analysis, outlier removal algorithm and ring projection. Using this algorithm, we achieve rotation-translation-scale invariant feature extraction. The force field are exploited to automatically locate the extrema of a small number of potential energy wells and associated potential channels. The image feature is acquired from relationship of local extrema using the ring projection method.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.7
• /
• pp.365-371
• /
• 2008

In this study, beat control method using an equivalent ring model is proposed to control beat period of a slightly asymmetric ring. Slight asymmetry in a ring generates mode pair and the interaction of the mode pair makes beat in vibration and sound. In a ring, as a simplified bell type structure, mode data are measured and an equivalent ring is determined so that the measured mode condition is satisfied. By the finite element analysis on the equivalent ring, changes of mode pair condition are predicted when local mass is attached or the local thickness is decreased. The predicted results are compared with the experimental result and the validity of the proposed method is verified.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.6
• /
• pp.114-122
• /
• 1999

By using the FEM, a method for the stress analysis of the presented dies has been proposed. In this method, FEM and Lame equation are used for the analysis of the die insert and the stress ring, respectively. The proposed method includes the calculation of the contact pressure between the die insert and the stress ring. To show the validity, the proposed method has been applied to the simple test problem. The results of the stress analysis have been compared with the results of ANSYS, a commercial FE-code. Cold extrusion has been simulated by using the rigid-plastic FEM and the results of the deformation analysis have been used as the input of the die structure analysis. The stress states of the prestressed extrusion die have been obtained. The stress analysis of the die insert with stress rings has also been performed during extrusion.