• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.241-247
• /
• 2003

The sealing performance of O-ring is effected in environments of the O-ring seal, like that applied pressure, working temperature, pre-compressed ratio and materials. In this paper, design of composite O-ring under pressurized, compressed was optimized based on Taguchi experimental design method. and it analysed numerically using non-linear finite element method. Ogden model in which is developed based on the experimental data is used for simulating the contact stress and strain in NBR and PTFE materials. Sensitivity analysis was performed with FEM results, which are contact stress, strain and temperature as variable.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.357-360
• /
• 2007

The profile ring rolling process of Ti-6Al-4V alloy was designed by finite element(FE) simulation and experimental analysis. The design includes geometry design and optimization of process variables. The geometry design such as initial billet and blank sizes, and final rolled ring shape was carried out with the calculation method based on the uniform deformation concept between the wall thickness and ring height. FEM simulation was used to calculate the state variables such as strain, strain rate and temperature and to predict the formation of forming defects during ring rolling process. Finally, the mechanical properties of profiled Ti-6Al-4V alloy ring product were analyzed with the evolution of microstructures during the ring rolling process.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.121-122
• /
• 2002

This paper presents contact behavior of an Polyperfluoroalkoxyethylene(PTFE) ring seals by a non-linear finite element method using the thermomechanical analysis. PTFE elastomer was assumed as odgen model for numerical analysis in FEM commercial code because elastomer has nonlinear behaviour character. The shape effects are investigated for sealing performance of ring seal in boundary conditions which as gas pressure, groove temperature and various O-ring seal models. Also contact stress and equivalent total strain are investicated. An O-ring seals was modeled four shape which are circle, two sunflower and X. The highest contact stress occurs at sunflower-ring seal with groove deapth of 0.35mm. the equivalent total strain of sunflower-ring seal is lower than that of the others under low gas pressure condition but under gas pressure condition over 4Mpa, that of sunflower-ring seal is higher. The calculated FEM results shows that the Sunflower-ring seal with groove depth of 0.35mm has excellent performance compared with other seal models.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.2
• /
• pp.49-55
• /
• 1999

This paper proposes an efficient 2D Finite Element Method(FEM) taking into account the end-ring of three phase squirrel-cage induction motors. The parameters of the squirrel-cage induction motor such as conductivity of secondary conductor have an effect on the characteristics of a motor. Especially, if the characteristic analysis is done without considering the end-ring, the good results can not be obtained. Therefore, we calculated a new resistivity of the secondary conductor including the end-ring's resistance to apply the 2D FEM. Then, the performances of the motors are analyzed by using the new resistivity of secondary conductor which contains the end-ring resistivity. The validity of the proposed method is verified by comparing the numerical results with experimental ones.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.5 s.54
• /
• pp.48-56
• /
• 2003

This paper has developed an efficient nonlinear finite element method that covers both initial deformations and initial stresses of general distribution in calculating the ultimate strength of ring-stiffened cylinders. The developed method and two widely-used commercial codes (NASTRAN and ABAQUS) were simultaneously applied to the same analysis model within the extent of those commercial codes' coverage to check the validity of the present method. After the validity check, it was used for parametric studies for more general cases of initial stress distribution, which produced some useful information about the imperfection sensitivity of the ultimate strength of ring-stiffened cylinders.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.51-59
• /
• 2003

This paper has developed an efficient nonlinear finite element method that covers both initial deformations and initial stresses of general distribution in calculating the ultimate strength of ring-stiffened cylinders. The developed method and two widely-used commercial codes (NASTRAN and ABAQUS) were simultaneously applied to the same analysis model within the extent of those commercial codes' coverage to check the validity of the present method. After the validity check, it was used for parametric studies for more general cases of initial stress distribution, which produced some useful information about the imperfection sensitivity of the ultimate strength of ring-stiffened cylinders.

• Tribology and Lubricants
• /
• v.19 no.1
• /
• pp.9-14
• /
• 2003

The sealing performance of an elastomeric O-ring using the double layered material has been analyzed fer the contact stress behaviors that develop between the O-ring seal and the surfaces with which it comes into contact. The leakage of an O-ring will occur when the pressure differential across the seal Just exceeds the initial (or static) peak contact stress. The contact stress behaviors that develop in compressed O-rings, in common case of dovetail grooved geometry, are investigated using the finite element method. The FE analysis includes material hyperelasticity and axisymmetry. The computed FEM results show that the contact stress behaviors are related to the ratio of diameter between the inner ring and the outer ring, and the temperature of vacuum chamber.

• Journal of the Korean Society of Safety
• /
• v.22 no.5
• /
• pp.13-20
• /
• 2007

Elastomeric O-ring seals are widely used in static and dynamic applications. A compressed and highly pressurized O-ring seal inserted under laterally one-sided constrained condition has been analyzed experimentally and numerically. The deformed shape and extrusion length of the O-ring under high pressure has been measured by the computed tomography. Through the comparison of experimental and FE results, the numerical analysis technique has been verified. Using verified FE method, the contact stress profiles at sealing surfaces have been investigated and their relevance to the 0-ring performance evaluated based on stress-related and displacement-related parameters. It has been found that the contact stress profiles and deformation behaviors of the seal are affected by friction coefficient, gap clearance, and pressure considerably.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.883-888
• /
• 2001

The theoretical method is developed to investigate the effects of ring stiffeners on free vibration characteristics and transient response for the ring stiffened composite cylindrical shells subjected to the impulse pressure loading. In the theoretical procedure, the Love's thin shell theory combined with the discrete stiffener theory to consider the ring stiffening effect is adopted to formulate the theoretical model. The concentric or eccentric ring stiffeners are laminated with composite and have the uniform rectangular cross section. The modal analysis technique is used to develop the analytical solutions of the transient problem. The analysis is based on an expansion of the loads, displacements in the double Fourier series that satisfy the boundary conditions. The effect of stiffener's eccentricity, number, size, and position on transient response of the shells is examined. The theoretical results are verified by comparison with FEM results.

• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.355-362
• /
• 2002

In this study, an axi-symmetric finite element program for elastic analysis of the die set shrink fitted in cold extrusion was developed. The geometrical constraint according to shrink fit was enforced by employing the Lagrange multiplier method. The numerical results for strain and stress distributions in the die set including single and multi stress rings assembled by shrink fit were compared well with the Lame's equation for thick-walled solution available in the literature. To extend the applicability of the analysis program developed, various cases without or with stress ring and with pre-stress applied on stress ring were numerically investigated as well. This numerical approach enables the optimization study to determine optimal dimensions of die set to improve tool life for practical use in industry.