• The Journal of Korea Robotics Society
• /
• v.9 no.1
• /
• pp.20-27
• /
• 2014

In this paper, an exact reshaping method for the motor dynamics of a flexible-joint robot is proposed using an integral manifold approach. Obtaining the exact model for both motor-side and link-side dynamics of a flexible-joint robot is difficult due to its under-actuated nature and complex dynamics. Despite the simple structure of the motor-side dynamics, they are difficult to model accurately for a flexible-joint robot due to motor disturbances, especially when speed reducers such as harmonic drives are installed. An integral manifold feedback control (IMFC) is proposed to reshape the motor dynamics. Based on the integral manifold approach, it is theoretically proved that the IMFC reshapes motor dynamics exactly even with bounded disturbances such as motor friction. The performance of the proposed IMFC is verified experimentally using a single degree-of-freedom flexible-joint robot under gravity conditions.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.255-257
• /
• 2007

In this paper, we develop a single wheeled robot that has one wheel to move. The single wheel robot is similar to a rolling disk relying on gyroscopic motions to balance. The Gyrobo consists of three actuators: a spin motor, a tilt motor and a drive motor. The spin motor spins a flywheel at high rate so that it provides the balancing stability to upright the robot. The tilt motor controls steering of the robot by gyroscopic effect. The drive motor make forward accelerated motion to the robot. We have built and tested the Gyrobo to turn and move forward.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.235-243
• /
• 2012

In this study, we developed two legged multi-joint robot by using wireless servo motor that was applied by wireless sensor network technology, which is widely used recently, and performed an experiment of walking method of two legged multi-joint robot. We constructed the star network with servo motors which were used at each joint of two-legged robot. And we designed the robot for operation by transmission of joint control signal from main control system or by transmission of the status of each joint to the main control system, so it operates with continuously checking the status of joints at same time. We developed the humanoid robot by using wireless digital servo motor which is different from existing servo motor control system, and controlled it by transmitting the information of angles and speeds of robot joints to the motor(node) as a feedback through main control system after connecting power and setting up the IDs to each joint. We solved noisy problem generated from wire and wire length to connection point of the control device by construction of the wireless network instead of using existing control method of wiring, and also solved problem of poor real time response to gait motion by controlling the position with continuous transmission of control signals to each joint. And we found that the effective control of robot is able by performing the simulation on walking motion in advance with the developed control algorithm which was downloaded into installed memory. Also we performed the stable walking with two-legged robot by attaching pressure sensor to robot sole. And we examined the robot gait operated by application of calculated algorithm on robot movement to each joint. In this study, we studied the method of controlling robot gait motion by using wireless servo motors and measured the torque applied to each joint, and found that the developed wireless servo motor by ZigBee sensor network offers easier control of two legged robot gait and better circuit configuration of it than the existing wired control system could do.

• Proceedings of the IEEK Conference
• /
• 2009.05a
• /
• pp.375-377
• /
• 2009

This paper researched the algorithm of robot's walking and action on the basis of robot studied and made at our laboratory and studied how to efficiently control the robot joints by developing wireless Digital Servo Motor using Zigbee Sensor Network Module which is using at wide part recently. I realized the stable walking by adopt Press Sensor at the bottom of robot foot to get stability of walking. Also I let the algorithm calculate the robot movement to make the joint motion and monitored the robot walk to its motion. At this Paper, I studied the method organizing the motion by the each robot walking and measuring the torque applying to the joint. And I also knew that it is possible to make its control and construct hardware more conveniently than them of the existing studied and controling 2Legs Walking Robot by applying it at walking robot and developing wireless servo motor by Zirbee Sensor Network.

• The Journal of Korea Robotics Society
• /
• v.8 no.4
• /
• pp.273-282
• /
• 2013

The purpose of this study was to investigate effect of robot-assisted hand rehabilitation(Amadeo(R)) on hand motor function in chronic stroke patients. This study used a single-subject experimental design with multiple baselines across individuals. Three chronic stroke survivors with mild to sever motor impairment took part in study. Each participants had 2 weeks interval of starting intervention. Participants received robot-assisted therapy(45min/session. 3session/wk for 6wks). Finger active range of motion(AROM) was assessed by Range of Assessment program in Amadeo(R), and test-retest reliability was verified using Pearson correlation analysis. To investigate effect of Amadeo(R), finger AROM was measured immediately after each sessions and Fugl-Meyer Assessment of Upper extremity, Motor Activity Log, Nine hole peg board test and Jebsen-Taylor hand motor function test were assessed at pre-post intervention. Results were analyzed by visual analysis and comparison of pre-post tests. The test-retest reliability of Range of Assessment was good(r=.99). After robot-assisted therapy, finger AROM of participant 1, 2, and 3 was respectively improved by 18%, 3.6%, and 6% each. Hand motor function of participant 1, 3 was improved on all four tests, but not effect in participant 2. Robot-assisted hand rehabilitation could improve finger AROM and effect on hand motor function in chronic stroke patients.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.4 s.316
• /
• pp.35-41
• /
• 2007

In this paper a single-wheeled robot called GYROBO is built and its hardware is implemented. The single-wheeled robot is similar to a rolling disk relying on gyroscopic motions to maintain its balance. The GYROBO consists of three actuators: a spin motor a tilt motor, and a drive motor. The spin motor spins a flywheel at a high rate so that it provides the balancing stability to upright the robot. The tilt motor controls steering of the robot by gyroscopic effect. The drive motor makes forward accelerated motion to the robot. Several models are designed. Experimental works of the GYROBO to turn and move forward have been presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.111.3-111
• /
• 2001

Automative system and robot are operated by motor. Recently, automative system and robot need correct operation and control for precise task. Therefore they need precise motor control technology. In present, controller needs precise motor control technology in automative system and robot. Usual step motor driver that has 200 steps per revolution is not proper. So we need micro step motor driver that is more precise then usual step motor driver. In this paper, micro step motor driver is used for precise control of step motor. The goal is precise operation and location control. This micro step motor driver is A3972SB that is made in Alloegro Company. It has serial port that receives two 6-bits linear DAC value. Almost all systems generate DAC value with micro processer and ...

• International Journal of Control, Automation, and Systems
• /
• v.5 no.3
• /
• pp.343-348
• /
• 2007

This paper presents an adaptive controller for the compensation of state-dependent disturbance with unknown amplitude in a digital servo motor system. The state-dependent disturbance is caused by friction and eccentricity between the wheel axis and the motor driver of a mobile robot servo system. The proposed control scheme guarantees an asymptotical stability for both the velocity and position regulation. An experimental result shows the effectiveness of the adaptive disturbance compensator for wheeled-mobile robot in a low velocity diffusion tracking. A comparative experimental study with a simple PI controller is presented.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.137-141
• /
• 2011

Driving mechanism, the central part of a robot, was designed in this study. Power for the motive drive was acquired by directly connecting the motor shaft in worm shape of the low-end DC motor, car window motor, to a decelerator. The decelerator consists of a worm gear to receive power from the motor shaft, a pinion gear to be connected in line with the worm gear, and an output shaft to be engaged to the pinion gear. Motion driving is achieved by the power from the motor shaft with the designed gears, transferred to the deceleration mechanism and to the output gear.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.3
• /
• pp.60-69
• /
• 1993

The speed control associated with dc servo motors for direct-drive applications of mobile robot is considered in this study. Robot is moved by power wheeled steering of two dc servo motors mounted to it. In order to cooperate with micro-computer and to achieve the high-performance operation of dc servo motor, speed control system is composed of a digital Phase Locked Loop and H-type drive circuit. And the motor is driven by Pulse Width Modulations. In controlling PWM, it is modified to compose of H-type drive circuit with feedback diodes and switching transistor and design of control sequence so that it may show linear characteristics. As a result, speed characteristics of motor showed linear features. In order to get data on design of PLL control system, the parameters of 80[W[ motor & robot device is measured by simple software control. The PLL speed control system is schemed and designed by leaner drive circuit and measured parameters. A complete speed control system applied to 80[W] dc servo motor showed good linearity, stability and high response. Also, it is verified that the PLL speed control system has good compatibility as a mobile robot driver.