• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.164-167
• /
• 2003

Profile ring rolling process is simulated by using the general purpose commercial finite element analysis software MSC.Superform Because the deforming region is restricted to the vicinity of the roll gap, only a ring segment spanning the roll gap is analysed in order to save computation time and cost. A profile ring with an external round groove is chosen as an example to be analysed. The rolls with and without groove were analysed to compare the amount of side spread. It is found that the grooves in the rolls reduce the amount of side spread.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.292-300
• /
• 1995

According to the number of cold-rolled coils, the amount of roll wear and thermal expansion, and roll gap profile were calculated, by using the actual data from the finishing mill. Also, based on those data, the calculations of the deflection, the flattening, and the contact pressure of vwork rolls and backup rolls were made respectively. Specially, in the calculation of contact pressure, the numerical results were obtained not only during the normal rolling, but also during the abnormal rolling, by modeling mathematically the dynamic impact force which occurs when the head section of the strip is threading through rolls. With those results the growth of the fatigue region and the fatigue damage of rolls were predicted. Also the optimum roll-grinding depth was determined to maximize the roll life.

• Transactions of Materials Processing
• /
• v.12 no.7
• /
• pp.631-639
• /
• 2003

Ring rolling process is simulated by using the general-purpose commercial finite element analysis software, MSC.Superform. Because the deforming region is restricted to the vicinity of the roll gap, only a ring segment spanning the roll gap is analyzed in order to save computation time and cost. First, a plain ring rolling of rectangular cross-section is simulated. Comparisons between computation and experiment show good agreement in the cross-sectional configuration of the deformed ring. Then, a profile ring with an external round groove is analyzed. The rolls with and without groove have been analyzed to compare the amount of side spread. It is found that the grooves in the rolls are effective in reducing the amount of side spread.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.499-504
• /
• 1993

To find a way for establishing work roll initial crown according to roll conditions, computer simulation for predicting plate crown in plate mill is done and effects of roll conditions on plate crown is analysed. Roll gap profile and plate crown are measured to be compared to the calculated values. As a result,a regression equation to establish work roll initial crown according to roll cooditions such as backup roll diameter, backup roll crown and work roll crown is obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.4
• /
• pp.723-730
• /
• 1998

With the introduction of edge drop control system in Tandem Cold Rolling Mill, it is necessary to develop te numerical expression for the set-up and edge drop automatic control of cold rolled sheet. As a first step we developed a simulation program which predicts profile and the amounts of edge drop at the delivery side of each stand by using roll deformation anlysis with the slit roll model. And by using the program the effect of various rolling conditions on edge drop was investigated. As a result the relations were obtained between the amounts of edge drop and rolling conditions. Based on above relations, the numerical expression was developed for the set-up and automatic control of edge drop by multi-regression of simulation results for the variation of edge drop amount with each rolling condition.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1296-1302
• /
• 2002

A mathematical model for cold rolling and temper rolling process of thin steel strip has been developed using the influence function method. By solving the equations describing roll gap phenomena in a unique procedure and considering more influence factors, the model offers significant improvements in accuracy, robustness and generality of the solution for the thin strip cold and temper rolling conditions. The relationship between the shape of the roll profile and the roll force is also discussed. Calculation results show that any change increasing the roll force may result in or enlarge the central flat region in the deformation zone. Applied to the temper rolling process, the model can well predict not only the rolling load but also the large forward slip. Therefore, the measured forward slip, together with the measured roll force, was used to calibrate the model. The model was installed in tile setup computer of a temper rolling mill to make parallel setup calculations. The calculation results show good agreement with the measured data and the validity and precision of the model are proven.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.286-287
• /
• 2008

The determination of roll speeds in continuous rolling system is an important factor along with the design of roll profile and roll gap. The tensile force on the workpiece induces reduced cross section area and the compressive force induces wrinkles. To determine the optimal roll speeds of current rough rolling system for wire rod, FE analysis was performed. We could predict the workpiece shape and the stress level more precisely by considering the elasto-plastic behavior of workpiece. Also the efficient analysis methodology is presented to reduce the calculation time by combining the ALE and lagrangian method.

• Journal of Mechanical Science and Technology
• /
• v.16 no.6
• /
• pp.785-798
• /
• 2002

A reliable analytic model that predicts the surface profile of the exit cross section of workpiece in round-oval (or oval-round) pass sequence is established. The presented model does not require any plasticity theory but needs the only geometric information on workpiece and roll groove. Formulation is based on the linear interpolation of the radius of curvature of an incoming workpiece and that of roll groove in the roll axis direction when the maximum spread of workpiece is known beforehand. The validity of the analytic model is examined by hot rod rolling experiment with the roll gap, specimen size, design parameter of oval groove and steel grade changed. Results revealed that the cross sectional shapes predicted by the model were in good agreement with those obtained experimentally. We found that the analytic model not only has simplicity and accuracy for practical usage but also saves a large amount of computational time in comparison with finite element method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1299-1304
• /
• 2010

We examined the working fracture behavior of a silicon-steel strip caused by deformation deviation by performing a pilot rolling test. The deformation deviation resulted in the edges (or center portion) of the strip being stretched and the other parts being compressed in the rolling direction; this was because of different degrees of deformation in these parts. We designed roll grooves shape to reflect the role of roll bending, which generates waviness in the strip in an actual cold rolling process, into the pilot rolling test. The material used in the rolling test was highsilicon steel (about 3%). The results of the test showed that the type of fracture in the strip specimen varied with the magnitude of the deformation deviation. The tensile stress produced at the strip edges because of the center waviness in the rolling direction was a crucial factor that resulted in edge cracking and a zigzag-shaped fracture at the center.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.1
• /
• pp.87-93
• /
• 2001

A reliable analytic model that determines the exit cross sectional shape a workpiece(material) in round-oval (oroval-round) pass sequence has been developed. The exit cross sectional shape of an outgoing workpiece is predicted by using the linear interpolation of the radius of curvature of an incoming workpiece and that of roll groovw to the roll axis direction. The requirements placed on the choice of the weighting function were to ensure boundary conditions specified. The validity of the analytic model has been examined by not rod rolling experiment with the roll gap and specimen size changed. The exit cross sectional shape and area of the workpiece predicted by the proposed analytic model were good agreement with those obtained experimentally. We found that the analytic model has not only simplicity and accuracy for practical usage but also save a large amount of computational time compared with finite element method.