• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.629-630
• /
• 2006

This paper describes a novel sensorless excitation position detecting method of Switched Reluctance Motor(SRM) drive. A suitable excitation pattern of each phases is determined by comparison of detecting current without an inductance estimation. The principle of the rotor position estimation is based on the detection of phase current according to rotor position. This sensorless method is very simple and gives efficient control of drive system. The suggested method is verified by experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.344-350
• /
• 2003

In this paper, an estimation technique of initial rotor position at standstill in Switched Reluctance Motor(SRM) is proposed. In case search coils are used as a position sensor, it has many advantages like low cost, decrease in the volume, high robust characteristics and wide applications. However, the initial rotor position detection is very difficult because the search coil's EMF is not exist at a standstill. In this paper, a near estimation method of initial rotor position is suggested using squared Euclidean distance. The simulation and experiment for the proposed method are achieved. The validity of the proposed method is verified by experimental results.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.352-361
• /
• 2018

This paper proposes a sensing system of the Halbach array permanent magnet spherical motor(PMSM). The rotor position can be obtained by solving three rotation angles, which revolves around 3 reference axes of the stator. With the development of 3-D hall sensor, the position identification problem of the Halbach array PMSM based on rotor magnetic field is studied in this paper. A nonlinear and serious coupling relationship between the rotation angles and the measured magnetic flux density is established on the basis of the rotation transformation theory and the magnetic field model. In order to get rid of the influence on position detection caused by the harmonics of rotor magnetic field and the stator coil magnetic field, a sensor location combination scheme is proposed. In order to solve the nonlinear equation fast and accurately, a new position solution algorithm which combines the merits of gradient projection and particle swarm optimization(PSO) is presented. Then the rotation angles are obtained and the rotor position is identified. The validity of the sensing system is verified through the simulation.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1004-1010
• /
• 2020

This paper proposes an initial rotor magnetic pole detection method for single-phase permanent magnet synchronous motors. The target motor cannot obtain position information based on the back emf in the low speed and stop state. Therefore, an open loop starting process is required, and in this process, initial rotor position information for low current and soft start is need. The proposed initial rotor magnetic pole detection algorithm considers the effect of asymmetric air- gap and magnetic flux. In addition, the high-frequency voltage signal injection and the offset voltage for accurate detection is used. As a result, the permanent magnet poles are is determined by acquiring the maximum value of the induced current using the virtual dq-axis.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.180-184
• /
• 2007

For driving a sinusoidal type permanent magnet synchronous motor with a maximum continuous torque, a $120^0$ delayed three phase sinusoidal current input which matched with the absolute rotor position is needed at a stator coil. So, the detection of absolute rotor position is required inevitably. Thus the right angle relationship between stator magnetic field and rotor magnetic field has to be preserved at a stator by this commutation action. The detection of a absolute position for the commutation can be made generally by the output signal analysis of the encoder attached at a motor shaft. This study purposes to design signal processing logic circuits which can detect the absolute position of motor with a modem encoder system and generate the three reference wave for making sinusoidal current input at a stator coil.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.65-69
• /
• 2011

This paper introduces the multi-coil eddy current sensor and its characteristic in magnetic material gas turbine rotor. In the past, magnetic particle inspection method was used for qualitative defect evaluation in magnetic material gas turbine rotor. And the ultrasonic inspection method was used for quantitative defect evaluation. Nowadays, eddy current method is used in magnetic gas turbine rotor inspection due to advanced sensor design technology. We developed multi-coil eddy current sensor for the rotor dovetail inspection. At first, rotor stress is analyzed for the determination of sensor position and number. The sensor coils are designed to cover the stress concentration area of rotor dovetail. We select optimum frequency according to material standard penetration data and experiment results. The rotor mock-up and artificial defects were made for the signal detection and resolution analysis of multi-coil eddy current sensor. The results show that signal detection and resolution capabilities are enhanced in comparison to the commercialized sensor enough for the gas turbine rotor inspection. So, this developed multi-coil eddy current sensor substituted for commercialized one and it applied in real gas turbine rotor inspection.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.709-712
• /
• 2000

In general three position sensors are needed to drive three phases SRM. Single position sensor driving method for three phases Switched Reluctance Motor(SRM) is proposed in this paper. By using single position sensor the cost of SRM is reduced. But position sensor the cost of SRM is reduced. But position detection at the staring is needed for single position sensor driving method. In this paper we propose the active align method to detect the relative position of rotor to three phases and align to the nearest phase. We proved the validity of the method by experiment and compare with other method.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.229-231
• /
• 2005

A sensorless control scheme for the switched reluctance motor (SRM) drive at speed control is presented in this paper. In this paper proposes a very simple method to estimate the rotor position of a switched reluctance motor. By on-line estimating the self-inductance of the motor, the rotor position of the SR motor is obtained, and a closed-loop drive system can be achieved. Proposed methods can easy implement to application with sensorless SR motor drive system. SR motor simulation executed with self inductance estimation and result represented.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.768-773
• /
• 1998

The speed control of SRM(Switched Reluctance Motor) needs the accurate position and speed data of rotor. This information is generally provided by a shaft encoder or resolver. In some cases, the environment is which the motor operates may cause difficulties in maintaining the satisfactory position detection performance. Therefore, the elimination of the position and speed sensor has gained wide attention. In this paper, a new algorithm for estimation of rotor position and speed is described for the SRM drives. This method uses is nonlinear adaptive observer using the MRAS(Model Reference Adaptive System). The observer is proved by Lyapunov Stability Theory. This algorithm was implemented with a TMS320C31 DSP. Experiment results prove that the observer is able to estimate the speed and position with a little errors.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.2
• /
• pp.135-140
• /
• 2010

This paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor. Depending on the terminal voltage sensing rotor position, active filter is used for position information. This leads to a significant reduction in the component device of the sensorless circuit. Therefore this is a advantage for the cost saving and size reduction. With indirect sensing methods based on detection of the terminal voltage that require active filtering, the position information needs the six divider section by PLL circuit, the binary counter and johnson counter by the EPLD. Finally, this algorithm can estimate the rotor position information similar to Hall-sensor sticked the three-phase BLDC motor. As a result, the method described that it is not sensitive to filtering delays, allowing the motor to achieve a good performance over a wide speed range. In addition, a simple starting method and a speed estimation approach are also proposed. Experimental and simulation results are included to verify the proposed scheme.