• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.554-560
• /
• 2003

The transmission systems of high speed train serve in the severe condition compared with those of other trains, namely, they have to transmit high power to run with high speed and they have to make maximum use of the limited space. To clarify the capability of reduction gear unit for Korea High Speed Train, torque and temperature, vibration on the reduction gear unit were measured and test data were analyzed. This paper reports test methods and test results that performed to verify reliability of reduction gear unit during running test of Korea High Speed Train. It is confirmed from these results that the performance of reduction gear unit has not any problem.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.267-270
• /
• 2001

A lot of efforts have been made to analyze the performance of the vehicle equipped with automatic transmission through simulation. It might be necessary to understand the different types of transmissions, i.e., different power flows, for different models. If there is a module that can be applied to different types of automatic transmission, it could be helpful to transmission-related engineers. This study has started up from this idea. The common bond graph has been obtained from several types of the automatic transmission. The overall generalized equations and kinematic constraint equations have been derived using virtual power sources on common bond graph. They are used to derive state equations and constraints. These equations have been applied as an application to the vehicle equipped with two simple planetary gear set type of Ravigneaux gear type automatic transmission. The state equation, kinematic constraints, and dynamic constraints have been derived in every gear and shift operation using overall generalized equations and kinematic constraint equations. Simulations for constraint speed running, standing-start running, rolling-start running, and LA-4 mode have been conducted to analyze the performance of the vehicle powertrain using GVPS(Generalized Vehicle Powertrain Simulation) program wit pull down menus.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.965-966
• /
• 2012

• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.133-138
• /
• 2007

Surface pitting is a major failure mode for gears. The contact fatigue life analysis of transmission gear considering running-in process is presented in this paper. Surface roughness change of rolling test is used in a life analysis. Contact stresses are obtained by contact analysis of a semi-infinite solid based on the use of influence functions; the subsurface stress field is obtained using rectangular patch solutions. Mesoscopic multiaxial fatigue criterion which can yield satisfactory results for non-proportional loading is then applied to predict fatigue damage. Suitable counting method and damage rule were used to calculate the fatigue life of random loading caused by rough surface. The life analysis considering running-in is in good agreement with the experimental results.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1731-1739
• /
• 2000

The Vibration signals of a gear driving system is often associated with gear tooth faults. Many studies have been done on the detection of impulsive vibration signals, which characterize the breaka ge of a gear tooth. Also, most of the studies on gear fault diagnosis are only about the fault existence at one gear-pair. This study concerns on the several possible faults of a geared motor that has three gear pairs. The measurement and analysis on the vibration signals of a running geared motor shows the relationship between the gear faults and the vibration signals. This study also shows that adaptive interference canceling technique can be appropriately applicable to detect which gear-pair has the fault, and that wavelet is better than spectrogram to figure out the gear fault.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.323-326
• /
• 2004

In these days, gear whine noise of the axle and transmission is getting more important for reduction of vehicle noise, because major noise of vehicle was reduced. Therefore, in this paper, axle noise and vibration is measured, and then the modal analysis and running modal analysis is applied for reduction of axle gear whine noise.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.999-1000
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1591-1592
• /
• 2013

• 열처리공학회지
• /
• 제33권6호
• /
• pp.303-309
• /
• 2020

A vehicle's differential gear is a device designed to allow the vehicle's outer wheels to turn faster than the inner wheels when turning on a curve. The differential gear case is the main component of the differential gear system, which is composed of ring gear, pinion gear and side gear, and is fastened by pinion shaft pins. The differential gear case rotates when the vehicle is running, so balancing calibration is very important. In this study, a balancing machine that can diagnose and correct the differential gear case and mass imbalance of various rotating bodies was designed. The differential gear case was rotated at high speed to accurately diagnose the location and value of the unbalanced mass, and it was designed to be balanced and corrected by removing the unbalanced mass by drilling. After calibration, it was confirmed that the unbalanced value of all the measured samples was reduced to less than 180g.mm, and the unbalance reduction ratio was improved to 60~70%.

• International Journal of Railway
• /
• 제2권1호
• /
• pp.8-17
• /
• 2009

The wheelset, its functions and position under the train is the prime safety-critical component. Whether in design, qualification, manufacturing or maintenance, the wheels and axles have been the focus of special attention at SNCF for over 25 years and the French Railways are actively involved in various Research and Development work towards interoperability between the railways, railway reliability and running safety.