• The Journal of the Acoustical Society of Korea
• /
• v.18 no.4
• /
• pp.53-59
• /
• 1999

Of various SPUDT SAW filter types, we select the two most common types, DART and EWC/SPUDT, and analyze their performance with the Smith equivalent circuit method. Based on the results for an exemplary case, a usual apodized SAW filter, we investigate the advantage of one type over the other, if any, in a quantitative manner. To compensate for the performance degradation that can happen in the process of the modification of the apodized filer to the SPUDT structure, we apply the triangular weighting technique to wide fingers of the IDT. Further, the variation in performance of the SPUDT structure is investigated in relation to its electrode thickness and the number of fingers. The results in this paper are expected to enable us to easily select an SPUDT type appropriate for each particular application field.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.359-362
• /
• 1999

본 연구에서는 작은 삽입손실을 구현하기 위해 적용되는 SPUDT 중에서 현재 가장 널리 사용되고 좋은 성능을 가지는 DART와 EWC/SPUDT형 SAW 필터에 대해서 그 효용성을 Smith 등가회로 해석법을 이용하여 분석하였다. 그리고 apodization weighting된 SAW 필터에 단순히 SPUOT를 적용하였을 때 발생하는 일부 특성열화를 보상하기 위한 방법으로, 이 두 종류 SPUDT의 폭이 넓은 전극에 대한 weighting을 독립적으로 행하였고 전극두께를 조절하여 성능변화를 보았다. 그 결과로 동일 전극길이를 갖는 경우에는 EWC/SPUDT형 SAW 필터가 DART형 SAW 필터보다 삽입손실이 더 작으나 리플이 크고, apodization weighting된 SAW필터에 SPUDT를 적용한 경우에는 전반적으로 DART형 SAW 필터가 EWC/SPUDT형 SAW 필터보다 우수한 성능을 가지는 것으로 나타났다. 본 연구의 결과는 특정 형태의 SAW 필터에 SPUDT를 적용하는 문제에 있어서 적절한 SPUDT의 타입을 결정하는데 도움을 주리라 기대된다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2374-2381
• /
• 2007

.We have studied to obtain the properly conditions about impedance matching of the SAW filter for the SPUDT type and the bidirectional transducer type later. And we have studied to obtain the SAW filter for the Slanted Finger Interdigital Transducer(SFIT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator In case the SPUDT, we have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000{\AA}$ and $3.6{\mu}m$, respectively. And the of the bidirectional transducer, the width of IDT' fingers and the space between IDT' finger and reflector is $1.8{\mu}m$, respectively. Also, we have performed to series connected the SPUDT type with the bidirectional transducer type filter. The frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bahdwidth at the 3dB is probably 5.3MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.3dB and insert loss is probably -20dB after when we have matched impedance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.602-608
• /
• 2005

We have studied to obtain the SAW filter for the Single Phase Unidirectional Transduce. (SPUDT), was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator. We can fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulations. Also, we have performed to obtain the properly conditions about impedance matching of the SAW filter for SPUDT. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are 5000A and $3.6{\mu}m$, respectively. And the width of IDT' fingers is $2.4{\mu}m$, and the space between IDT' finger and reflector is $2.0{\mu}m$. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 7.7MHz after when we have matched impedance. Also, we could obtain that ripple characteristics is less than 0.4dB and standing wave ratio is probably 1.5 after when we have matched impedance.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.33-40
• /
• 2006

This paper presents a novel surface acoustic wave (SAW)-based pressure sensor, which is composed of single phase unidirectional transducer (SPUDT), three reflectors, and a deep etched substrate for bonding underneath the diaphragm. Using the coupling of modes (COM) theory, the SAW device was simulated, and the optimized design parameters were extracted. Finite Element Methods (FEM) was utilized to calculate the bending and stress/strain distribution on the diaphragm under a given pressure. Using extracted optimal design parameters, a 440 MHz reflective delay line on 41o YX LiNbO3 was developed. High S/N ratio, shan reflection peaks, and small spurious peaks were observed. The measured S11 results showed a good agreement with simulated results obtained from coupling-of-modes (COM) modeling and Finite Element Method (FEM) analysis.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.10
• /
• pp.1916-1923
• /
• 2007

We have studied to obtain the SAW filter for the passband was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and thin we performed computer-simulated by simulator. We cm fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have performed to obtain the properly design conditions about phase shift of the SAW filter for WCDMA. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000\;{\AA}$ and $3.6{\mu}m$ respectively. And we have employed that the distances from the hot electrode to the reflector are $2.0{\mu}m$, $2.4{\mu}m$ and the distance from the hot electrode to the ground is $1.5{\mu}m$ respectively. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 7,8MHz. And we could obtain that return loss is less then -18dB, ripple characteristics is probably 3dB and triple transit echo is less then -25dB after when we have matched impedance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.2
• /
• pp.307-315
• /
• 2005

We have studied to obtain the SAW filter for the passband was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and then we performed computer-simulated by simulator. We can fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have performed to obtain the properly design conditions about phase shift of the SAW filter for WCDMA. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are 5000$\AA$ and 3.6$mu$m, respectively. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 8.2MHz. And we could obtain that return loss is less then 16dB, ripple characteristics is probably 4dB and triple transit echo is less then 18dB after when we have matched impedance.