• Journal of Korea Water Resources Association
• /
• v.49 no.12
• /
• pp.981-993
• /
• 2016

This study explains the GIS database of flood inundation area developed for Samsung-1 Drainage Sector, Seoul, Korea. The XP-SWMM dual drainage model was developed for the study area, and the time series observed at the watershed outlet was used to obtain the watershed time of concentration and to calibrate the XP-SWMM model. The rainfall scenario was developed by dividing the 40 minute watershed time of concentration into two 20-minute time steps and then applying the gradually increasing 5 mm/hr interval rainfall intensity to each of the time step up to 200 mm/hr, which is the probable maximum precipitation of the study area. The developed rainfall scenarios was used as the input of the XP-SWMM model to obtain the database of the flood inundation area. The analysis on the developed GIS database revealed that: (1) For the same increment of the rainfall, the increase of the flooded area can be different, and this was caused by topographic characteristics and spatial formation of pipe network of the study area; (2) For the same flooded area, the spatial extent can be significantly different depending on the temporal distribution of rainfall; and (3) For the same amount of the design rainfall, the flood inundation area and the extent can be significantly different depending on the temporal distribution of rainfall.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.7 no.1
• /
• pp.28-38
• /
• 2004

The purpose of this study is to analyze the urban hydrologic state by the use of GIS, resolution and interpolation. The determination coefficient($R^2$) and Regression Formula were derived from the contour of digital map for the accuracy, and DEM data was made by using TIN interpolation by the size of the grid. By using the observed DEM data, topographical factors were extracted from the small basin, size, the width of a basin and the slope, and were applied in the urban runoff model. Through the model, we tried to find out the most suitable runoff model in a small basin of Yosu-Munsu area. As a result of applying models to the drainage considered, the runoff hydrograph estimated by SWMM model was closer to the observed one than that estimated by ILLUDAS model. The difference between the runoff hydrograph by SWMM and the observed one is maximum error of 19%, minimum error of 5% and average error of 13%. The influence of duration in contrast to pick time is insignificant in a urban small basin. As a conclusion of this study, SWMM model was more suitable and applicable for the urban runoff model than ILLUDAS model due to its accuracy and various abilities.

• Journal of Korea Water Resources Association
• /
• v.50 no.6
• /
• pp.397-405
• /
• 2017

In case of inundation in a city where populations and properties are highly concentrated, unlike rural areas it is necessary to apply the method of calculating the damage amount considering the sewage overflow and the corresponding building damage. In this study, Dorim 1 drainage sector has been analyzed with Multi-Dimensional Flood Damage Assessment (MD-FDA) for flood forecast. It is analyzed with past flood history through the SWMM model and calculated the amount of damage with district base data and the result of flow analysis. The result of the SWMM model to predict a range of flood, it was shown that the wide area after 4 hours (at 16:30) by sewer overflow. The building damage was estimated using MD-FDA. As a result, the maximum flood area has shown as $205,955m^2$ (0~0.5 m: $205,190m^2$, over 0.5 m: $865m^2$) and estimated building damage of Dorim 1 drainage sector is approximately 15.5 billion KRW (Korean won) and other contents is 7 billion KRW (Korean won). Also from 0 to 0.5 m depth estimated damage is approximately 22.4 billion KRW (Korean won) and over 0.5 m is 100 million KRW (Korean won). Based on the results of this study, it would be necessary to estimate the amount of sub-divided flood damage in urban areas according to various damage patterns such as flood depth and flood time.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.5
• /
• pp.565-572
• /
• 2009

Hydraulic modeling is widely used to simulate wastewater flow. The simulated models are used to prevent flood and many other problems associated with wastewater flow in planning or rehabilitating sewer systems. In this study, MAKESW (An engineer, South Korea), MOUSE (DHI, Denmark), and SWMM (XPSoftware, USA) are used to for hydraulic modeling of wastewater in C-city, South Korea and E-city, Iraq. These modeling tools produced different results. SWMM comparably overpredicted runoff and peak flow. In using SWMM, use of accurate data with a high confidential level, detail examination over the target basin surface, and the careful selection of a runoff model, which describes Korea's unique hydraulic characteristics are recommended. Modification of existing models through the optimization of variables cannot be achieved at this moment. Setting up an integrated modeling environment is considered to be essential to utilize modeling and further apply the results for various projects. Standardization of GIS database, the criteria for and the scope of model application, and database management systems need to be prepared to expand modeling application.

• Journal of Environmental Health Sciences
• /
• v.31 no.6
• /
• pp.467-474
• /
• 2005

The runoff characteristics of combined sewer overflow(CSO) in the urban area of Jeonju were investigated and analyzed by using the SWMM (Storm Water Management Model) and GIS. From August to November 2004, investigations on two rainfall events were performed and flowrate, pH, BOD, COD, SS, T-N and T-P were measured. these data were used for model calibration. Using GIS technique, watershed characteristics of study area were calculated. that is, divide into sub_basin, total width, slope, make soil map etc. On the basis of the measured data and the simulation results by SWMM, it could be known that the $80-90\%$ of pollution load are discharged in early-stage storm runoff. SMC(site mean Concentration) for combined sewer system area were BOD 28.1, COD 31.5, SS 186 ppm etc. this is shown that during the rain fall, high concentration of waste was loaded to receiving water. Unit loads of combined sewer system area were BOD 306, COD 410, SS 789, T-N 79, T-P 6.8 kg/ha/yr.

• Proceedings of the Korea Contents Association Conference
• /
• 2013.05a
• /
• pp.97-98
• /
• 2013

최근 빈번하게 발생하고 있는 국지성 집중호우로 인한 해안 도시지역의 내수침수 원인 및 면적을 XP-SWMM 모형을 이용하여 분석하였다. 이 연구의 대상은 해안과 인접한 지역이며, 유역의 면적은 $2.74km^2$이고 관로의 총연장은 11.20km이다. 대상지역을 32개의 소유역과 67개의 하수관로로 XP-SWMM 모형의 입력자료를 구축하였다. 대상유역에 대한 강우분석을 수행하여 2년, 5년, 10년, 20년, 30년, 50년 빈도의 강우량을 결정하였으며, 각 빈도의 강우사상에 대하여 조위조건을 반영한 침수해석을 수행하였다. 우수관거시스템과 연계된 TUFLOW 흐름모형을 이용하여 침수범람지역을 모의하였다. 모의 결과 모든 빈도에 대하여 내수침수 현상이 발생하는 것으로 나타났으며, 빈도별로 최대침수심은 0.485~0.673m, 침수면적은 $88,600{\sim}230,700m^2$로 예측되었다. 대상유역의 침수발생 양상은 하수관로의 유량이 맨홀을 통해 지표면으로 분출되는 현상이 발생하며, 이 지역의 하류로 침수범위가 확대되는 것으로 나타났다. 이런 현상은 상류에 위치한 소유역의 우수 유출량을 집수하는 집수정의 용량과 하류로 유하시키는 우수관로의 통수단면이 부족한 것을 주요 원인으로 생각할 수 있다.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.41 no.5
• /
• pp.68-77
• /
• 2013

Change in the Global Climate causes flood, drought, heavy snow, and rainfall patterns in the Korean Peninsula. A variety of alternatives related to climate change are considered. The foreign researchers are interested in Low Impact Development(LID); the utilization of water resources and eco friendly development, over 10 years ago. The research and development of related technology has been advanced to apply LID techniques in order to develop several projects in the country. However, sharing of technology or system that can be used easily in the private sector is insufficient. The performance of the elements of LID Technology has not been fully agreed. LID elements of this technology are easy to apply to Apartment complex. The elements are classified technology. The infiltration of elements performs the functions of apartment complex landscaping space technology applied to the target. The water cycle simulation(SWMM 5.0) and technology the implementation of the effectiveness is also verified. For this purpose, three different places in apartment complex to target by SWMM5.0 U.S. EPA conducted utilizing simulated rainfall and applying LID techniques before and after the simulated water cycle (infiltration, surface evaporation, and surface runoff) were conducted. The importance of green space in the LID techniques of quantitative and qualitative storm water control as well as the role of Apartment Housing is to promote Amenity. Remember that the physical limitations of apartment complex and smooth water circulation system for the application of LID integrated management techniques should be applied. To this end, landscapes, architecture, civil engineering, environmental experts for technical consilience between the Low Impact Development efforts are required.

• Journal of Korean Society on Water Environment
• /
• v.34 no.3
• /
• pp.308-315
• /
• 2018

SWMM-LID was calibrated with flow monitoring data in LHI to evaluate runoff after LID application. The flow rate in the B basin was estimated to be 0.94 and 6.15 for O/S and $D_v$, respectively. In the A and C basins, the difference between the observed and simulated data was greater than in the B basin. As a result of runoff reduction efficiency by the application of LID facilities, the change of infiltration increased from 34.6 % to 45.8 % in the entire watershed, and the runoff decreased from 58.8 % to 46.3 %. In the runoff reduction of each LID facility, rain garden E showed the highest effect with 99.9 % and bioretention B showed the lowest effect with 27.5 %. In order to evaluate the efficiency of each LID facility, a comparison is made between the pore volume (V) of the LID and the catchment area (A). The runoff showed a runoff reduction effect of about 70 % above the 0.1 volume/area (V/A) value. As a result of examining the runoff reduction with LID facilities by the LID module of SWMM, a reasonable design is possible by reflecting the appropriate LID volume to drainage area.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.31-31
• /
• 2018

본 연구는 내수침수에 의한 침수면적 예측을 위하여 1차원 유출모형의 유출특성을 이용하여 침수면적 예측방법의 최적화이다. 2017년 강우의 초기강우와 첨두강우 특성을 적용한 경우에 정확한 침수면적 추정이 가능한 것을 확인한 바가 있다. 이러한, 결과에 추가적으로 SWMM 모형의 유출결과 자료의 특성인자를 이용하여 침수DB를 선택한 경우에 침수면적 예측 정확도를 분석하였다. 강우지속시간 및 강우량의 변화에 따른 유출결과의 변화를 분석하여 강우특성에 따른 SWMM 모형의 노드별 유출결과의 특성인자 변화를 분석하여 침수DB에서 실제 침수면적 선정방법을 정리하였다. 정리된 방법을 이용하여 유출결과 자료 특성인자를 이용한 최적의 침수DB 선정방법을 돌출하였다. 강우 특성 인자에서 침수DB를 선정하는 방법과 비교하여 강우유출모형의 모의결과를 이용한 경우에 약 6,000여개 노드를 기준으로 5~10분의 모의시간이 추가적으로 소요되어 실시간 침수 DB 선정에는 어렵지만, 준실시간 실제 유출량을 고려한 침수DB 선정이 가능할 것이다. 따라서, 강우특성 도출에 따라 1차적으로 침수DB를 선정하고, 강우유출모형의 유출 특성에 따라서 2차적으로 침수DB를 선정한다면, 예경보 시스템에서 대응시간 확보와 예측 정확도 유지에 긍정적인 방안으로 도입될 수 있을 것이다. 침수DB 구축은 많은 침수면적 산정연구에 이용하였던 TUFLOW 모형을 이용하여 침수DB를 구축하였다. SWMM 모형을 이용하여 강우유출을 모의하고, 침수면적을 TUFLOW를 이용하여 구축한 다양한 호우사상에 대한 침수DB를 이용하여 준실시간 침수면적 예측하는 방법은 향후, 예경보 시스템 구축에 이바지 할 수 있을 것입니다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.195-195
• /
• 2022

도림천의 최상류인 관악산 유역에 서울대학교 관악캠퍼스가 건설되었다. 이로 인해 물순환은 기존의 자연 상태에서 점점 변해 왔는데, 이는 하류 도림천의 홍수 및 수질 오염의 피해를 증가시켰다. 도시화된 서울대학교 관악캠퍼스의 물순환 회복은 하류 홍수피해 방지와 지속 가능한 친환경 캠퍼스를 위해 중요하나, 이에 관한 연구는 미흡한 실정이다. 따라서 본 연구에서는 SWMM(Storm Wastewater Management Model)을 활용하여 캠퍼스 내 물순환 현황을 시간과 공간에 대해 정량적으로 파악하고, 물순환 회복을 위해 지속 가능한 효율적인 시스템을 구현하고자 한다. 먼저 유역 현황 조사와 함께 SWMM 구축에 필요한 수문·기상학적 변수와 물리적 매개변수를 확립하였다. 수문·기상학적 변수로는 기상관측장비 ATMOS-41의 설치와 기상청 자료로부터 수집하였으며, 물리적 매개변수는 환경부의 자료를 활용하였다. 그 후, 서울대-도림천 배수분구에 대해 SWMM을 적용하여 월별로 유출량, 침투량, 그리고 증발산량을 모의하였다. 시간에 따른 물순환 분석의 경우 강수량 자료와 불투수율의 변화 정도에 따라 월별 물수지 비율을 파악하고, 공간에 따른 물순환 분석의 경우 동일한 기간에 대해 분할한 16개의 소유역 별 유출량과 유역의 평균 유출량을 비교하여 분석하였다. 대상 유역의 월별 물수지 비율을 모의하는데 효율성을 높이고자 배수 구역 및 관망을 세밀하게 나눈 경우와 그렇지 않은 경우에 대해 분석하였다. 그 결과, 시간에 따른 연평균 물수지 비율의 차이는 2020년 모의 결과와 최근 5년 평균(2015~2019년) 모의 결과 비교 시 각 물수지 항목별로 0.47~2.34%의 차이를 보였다. 공간적으로는 16개 소유역 중 저류시설을 포함한 9개 소유역의 표면 유출량이 유역의 평균 유출량보다 많게 모의 되었다. 또한, 유역을 구성할 때보다 관망을 구성할 때 높은 정확성이 요구됨을 알 수 있었다. 본 연구는 ATMOS-41을 통한 지속적인 수문·기상학적 요소의 모니터링과 SWMM 모델 구축을 통해 앞으로도 변경사항을 추가함으로써 친환경 캠퍼스로의 전환에 이바지할 것으로 기대한다.