• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.80-81
• /
• 2014

환경보호 정책에 대응하고 보건 및 안전의 수준 향상을 위한 수용성 도료의 적용 시, 일부 도장 공정에서 도막 건조의 지연으로 sagging 현상이 발생하였다. 이러한 sagging 현상이 일어난 원인을 실험을 통해 분석한 결과, 도료가 갖는 고유의 yield stress와 더불어 습도 및 통기 상태 등의 시공 환경이 지배적인 영향을 미친다고 파악되었다. Sagging 현상의 재발을 방지하기 위해서는 높은 sagging 저항성을 갖는 도료의 선정뿐만 아니라 도장 공장의 적절한 온/습도 및 환기 제어가 선행되어야 한다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.157-160
• /
• 1999

Aluminum 4343(filler thickness ; 10${\mu}{\textrm}{m}$/Al 3N03(core 80${\mu}{\textrm}{m}$)/Al 4343(filler 10${\mu}{\textrm}{m}$) clad sheet which is recently developed as brazing sheet materials for automotive condensers was fabricated by castinglongrightarrowhot rollinglongrightarrowcold rollinglongrightarrowintermediate annealing(IA)longrightarrowfinal cold rolling(CR). and the effect of IA/CR conditions on microstructure and sagging resistance were investigated the sheet which were fabricated by optimum conditions (IA'ed at 42$0^{\circ}C$ followed by CR'ed to 20~45%) showed good sagging resistance because the core obtained a coarsely recrystallized grain structure during brazing and consequently inhibited filled alloy penetration into the core.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.227-227
• /
• 1999

The effects of intermediate annealing (IA) and the final cold rolling (CR) condition on the microstructure and sagging resistance during brazing were investigated using three layer clad sheets composed of the Al-7.5 wt.%Si alloy (filler, thickness: 10 ㎛)/Al-1.3 wt.%Mn based alloy (core, 80㎛)/Al-7.5 wt.%Si alloy (filler, 10㎛). Also, the effect of 1.2∼2 wt.% Zn addition into the core on the sagging resistance of the clad sheets was determined. It was revealed that all the clad sheets fabricated by the optimum condition (IA at 690 K and CR to 20∼45%) show excellent sagging resistance with a limited erosion due to the formation of a coarsely recrystallized grain structure in the core during brazing. It was also revealed that the recrystallization behavior of the Al-1.3 wt.%Mn based alloy is hardly affected by the addition of 1.2-2 wt.%Zn during the brazing cycle. Therefore, the sagging resistance of the clad sheets is found to be governed not by the Zn content added in the A1-1.3wt.%Mn based core, but by the intermediate annealing and final cold rolling condition.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.1-5
• /
• 2018

The present study investigated the characteristics of vertical sagging down of high temperature in chamber and characteristics of vertical sagging down in the outdoor asphalt sheet and asphalt seal under korea ltimate condition using asphalt seal products of solvent based type, solventless type, water dispersion type, and heat melting type, which are currently applied in Korea. Prior to the investigation of outdoor vertical sagging down characteristics, the assessment of sagging down performance of single use of sealing products at $20^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$ was conducted and the result showed that sagging down did not occur at $20^{\circ}C$ but some solventless type, water dispersion type specimens at $40^{\circ}C$ had sagging down up to 10 mm. In addition, some solventless type, water dispersion type specimens had sagging down up to 55 mm at $60^{\circ}C$. For specimens to which asphalt seal and renovated asphalt sheet were layered over the outdoor concrete vertical surface, sheet sagging and sagging down occurred up to 50 mm in water dispersion specimens after three month later since the construction in summer.

• Journal of Korean Institute of Industrial Engineers
• /
• v.34 no.1
• /
• pp.57-65
• /
• 2008

In the vehicle design, the research on driving posture has stood out as one of the important issues. Recently, the research on 3D human modeling focused on more exact implementation of real driving posture. However, prediction of driving posture through the 3D human modeling fail to reflect on the model the phenomenon called sagging, which refers to the retraction or shrinking of the torso while driving. 30 male subjects participated in the experiment where total subjects were divided into four groups according to height percentile(under 50%ile, 51%ile to 75%ile, 76%ile to 95%ile, over 95%ile). The independent variables were seat back angle(4 levels) and seat pan angle(2 levels). The dependent variable was capacity or the degree of retraction of the torso. First this study measured the sagging capacity by using a paired T-test between erect and retracted posture. Secondly it was tried to find out significant anthropometric variables that were statistically correlated by the analysis of correlation. Finally, a prediction model was derived which explains the capacity of sagging.

• Journal of computational fluids engineering
• /
• v.17 no.4
• /
• pp.75-80
• /
• 2012

Due to the effect of surface tension, liquid film around a curved edge of solid surface moves from the corner to the flat surface. During this behavior of liquid film, film sagging phenomenon is easily occurred at the solid surface. Behavior of liquid film is determined with the effects of the properties of liquid film and the geometric factors of solid surface. In the present study, 2-D transient CFD simulations were conducted on the behavior of liquid film around a curved edge. The two-phase interfacial flow of liquid film was numerically investigated by using a VOF method in order to predict the film sagging around a curved edge. In the steady state of behavior of liquid film, the liquid film thickness of numerical result showed a good agreement with experimental data. After verifying the numerical results, the characteristics of behavior of liquid film were numerically analyzed with various properties of liquid film such as surface tension coefficient and viscosity. The effects of geometric factors on film sagging were also investigated to reduce the film sagging around a curved edge.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.48-55
• /
• 2010

The Door hinge is a very important part for door sagging performance of a vehicle. It is divided into two classes as a forge- and press-type according to a manufacturing technique. The press-type door hinge is cheap, but shows low strength. To apply the press-type door hinge to a fullsized car with satisfactory door sagging performance, we optimized the design parameters of the door hinge using the DFSS method. As a result, the effective design parameters of the press-type door hinge with good door sagging performance were obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.2
• /
• pp.145-151
• /
• 1997

In this paper, we discuss the cathode ray tube(CRT) glass bulb stress and sagging recovery by the contact band pressure using finite element method. We analyzed the band pressure and stress using contact element method between band and bulb before and after banding process which was conducted to decrease the stress concentration using finite element method, and calculated sagging recovery. The analysis results were confirmed by experiments using strain gauge and sagging recovery test apparatus.

• Steel and Composite Structures
• /
• v.15 no.4
• /
• pp.425-438
• /
• 2013

A new-styrofoam-concrete composite sandwich slab with function of heat insulation is designed. Four full-scale simply supported composite sandwich slabs with different shear connectors are tested. Parameters under study are the thickness of the concrete, the height of profiled steel sheeting, the influence of shear connectors including the steel bars and self-drilling screws. Experimental results showing that four specimens mainly failed in bending failure mode; the shear connectors can limit the longitudinal slippery between the steel profiled sheeting and the concrete effectively and thus guarantee the good composite action and cooperative behavior of two materials. The ultimate sagging bending resistance can be determined based on plastic theory. This new composite sandwich slab has high sagging bending resistance and good ductility. Additionally, these test results help the design and application of this new type of composite sandwich slab.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.1
• /
• pp.1-16
• /
• 2021

This study classified short adult male body types and identified characteristics by body type according to Size Korea's 7th human system measurement data for men in their 20s to 60s. There were four body types for short adult males. Type 1 was a 'short bird legs-normal body shape' with an average body size, low body height, short torso length, thin legs, and no sagging shoulders. Type 2 was a 'short torso thin body' with a small body size, a slim body, a high body height, a short torso length and no sagging shoulders. Type 3 was a 'thick leg-overweight body shape' with a large body size, thick legs, low body height, small shoulder length and obesity. Type 4 was a 'long bird legs-normal body' with a normal body size, high body height, thin legs, long torso and sagging shoulders. The development of clothing design and pattern reflecting the body shape characteristics of short adult males should be improved to fit clothing and suitability. It is necessary to increase the satisfaction of ready-to-wear for consumers with various body types by adding the size for shorter men through a subdivision of the ready-made size system.